How To Repair Power Problem Of Bajaj Induction Cooker (Step By Step) - English Tutorial

[@HEMRAJ-eu4lg]

Good presentation. Deserve merit.😀

[@joserodriguez2632]

Very well explained thanks and keep those videos in English,please.

[@CreativeWorldPro]

sure

[@dammikadammika3828]

Good video sir, congratulations 🍾 🎉 to you.🇱🇰🙏

[@hosraiyan]

If you continue english tutorial i will subscribe. I appreciate youre work sir thanks.

[@CreativeWorldPro]

i might try my best

[@jayamelectricalspares6358]

yes. sir . i am also knowing in english only

[@mani6678]

Thanks brother for your information. I will try it.

[@JakirHusain-cl4gm]

Varry good information sir. Sir Bajaj icx4 model me 4 pin ic ka nambar kya h. Please reply. Argent

[@rishielectronet]

Sir, what is the value of the diodes you replaced? And what alternative diodes can be used instead?

[@rishielectronet]

Sir, what volt is the zener diode value near the IGBT?

[@AchuchettanKLEsports]

Thank you bro. It's very useful for me.

[@vamsivamsi853]

hi very informative and practical video brother, i appreciate u. my philips 4909 induction cooker not switching on, checked bridge rectifier igbt are ok. 18v 5v not coming, observed 230 dc voltage coming upto r33 low resistance protection resistor but output not coming, r33 resistor showing open-- i think this resistor connects to 450 v capacitor-- may i know the value of this resistor? --one more observation is diode before 50 v capacitor showing short(50 ohms) , in diode mode voltage showing zero-- may i know the model no. of this diode?

[@CreativeWorldPro]

resistor value 0.33 ohm

[@vamsivamsi853]

@@CreativeWorldPro tq bro, I'll try to resolve it, but one more observation is 50v capacitor in smps circuit showing short, shall I replace this capacitor also?

[@sanjibmandal8891]

Sir l have Bajaj majesty induction today start the oven but panel bord show 88:88 no hiting no fan move no on/off switch work pls solv the problem sir

[@rajakumarsingh3145]

Bhai new induction me ceramic vs glass kon better hoga Prestige ka ceramic atlus 3.0 1200watt. Vs pigeon crystal glass favorite ic 1800watt. Kon accha hoga? ?

[@CreativeWorldPro]

Pigeon crystal glass 1800 watt will produce, high temperature

[@rajakumarsingh3145]

Kon sa lu

[@sandipchatterjee2392]

Induction me coil sensor kaha pe hota hai... Please rply

[@johnmoisessantos6390]

Thank you sir for the informative video

[@CreativeWorldPro]

Always welcome

[@lalkahandawa8923]

Last two diodes why did you fix revers. White line has to be on the arrow point side is it?

[@bachichunduryify]

Hi we can test many items without Removing components

[@kajiasadurrahaman8329]

I have problem in pulse module section.. And that have smd components what i can repair it..i have already changed igbt.. So please help me sir

[@CreativeWorldPro]

now, what't happening ?

[@kamal54382]

if voltage above 250 -300 then induction work krega?

[@CreativeWorldPro]

what is value of filter capacitor ?

[@abdulakhan3561]

Please help me 7073563753

[@nitinbhengra38]

Sir in this smps C102 is of what value n is it a smd resistor???

[@CreativeWorldPro]

C 102 capacitor value = 0.001 uf

[@nitinbhengra38]

Thank you

[@rajamramjee1705]

Dear Sir, I have a Citron make induction stove. display changes ok. but not heating shall I procee d as in your video ??

[@CreativeWorldPro]

sure, you can try..

[@olusanyaabisoye3138]

In my induction cooker I saw that two diodes burnt at point of the last two diodes you replace. What can made it to blown?

[@CreativeWorldPro]

short circuit or high voltage

[@olusanyaabisoye3138]

@@CreativeWorldPro thanks for time sir, Have replace the two burnt diodes still yet my induction cooker didn't come up. Have checked the igbt, bridge rectifier, the 22 ohms resistor, 4.7uf capacitor all these are in good condition. But I discovered that the voltage at voltage regulator IC 78L05 is 0.02v , am expecting more than that. Please help me on this. The induction cooker is Preethi, the board is like the one you are working on, it has same components arrangement

[@pandiarajan6973]

Hi Bro.... what is the value of R30 For me it's blown...

[@AkhilSingh]

i have a bajaj majesty icx neo it has a capacitor in round shape dark yellow can you name it please

[@kuldeeptiwari9384]

What is the role of preset its value and how to adjust the preset. Preset gives the value 5.39 k . Problem with the set is slow heating .

[@hmmm328]

i have same induction cooker getting err 9 but only in 1 induction kadhai but other cookware works fine? how to find problem

[@siddharthasahoo508]

Induction igbt collector section main 640 volt aa raha hai toh iska solution kya hai plz comment

[@28-arjunmp37]

Can we replace uf 4007 with 1n 4007. is there any problem while changing it

[@CreativeWorldPro]

i think there will be no problem,, you can use it easily

[@28-arjunmp37]

@@CreativeWorldPro thank uuu

[@manojmahatara7960]

Sir bajaj ki induction me IGBT H15R1203 short huwa he lekin uskee badle me 25N120/03 IGBT dal sakte hain help me plz sir bata dijiye na

[@CreativeWorldPro]

yes, you can use

[@msstipsentertainment6711]

Aap Jo hit sing me se khol rahe ho usko kya bolts hai kya iska number bhi hota hai please batae

[@CreativeWorldPro]

1 of them is Bridge Rectifier and 2nd of them is Mosfet, It's value is H20R1203

[@WStarTM]

Bro iska agar spare part lena ho to iska keypad not work i want change keypad Bajaj induction cooker Majesty Icx 7

[@manotoshdasdas1666]

Dada R30 koto ohms resistor janale khub upokar hoy

[@CreativeWorldPro]

0.3 ohm

[@standard.brahma]

what is that small coil. What does it do?

[@sumankumar1523]

Hi. I have a phillips induction cooktop 2100W HD4928/01. The SMPS circuit IC & big resistor are blown. I bought new Viper 12a IC but couldn't get the bid resistor as the colors are not visible. Can u help me?

[@CreativeWorldPro]

you can check the circuit board again,,there may be write down the value of the resistor

[@veluvelu654]

Suman Kumar

[@harvinderhs1644]

Sir same model hai hamara problem hai power plug lagane par buzzer bajta hai panel me ek baar light bhi aata hai or baad me light band ho jata hai on switch pres karne par on nahi hota panel par 5volt supply bhi aa rahi hai switch nikal kar check kar liye hai sabhi problem same hai kya check kar please suggest

[@FuckYouGOD-tp8iu]

I follow your instruction it's good for us...but i am facing a problem here,the induction run like in half cycle(run for 3/4 sec then off* continuesly

[@CreativeWorldPro]

which company induction you use ?

[@FuckYouGOD-tp8iu]

Thanks for your precious time...well i did replace the variable resistor and a feeback resistor if i am not mistaken and it worked well...thanks alot

[@FuckYouGOD-tp8iu]

@@CreativeWorldPro Bajaj majesty ICX7 i find C2 short is it normal? And i think the induction is running full speed and fast? It runs for a couple of hours and blows the MOSFET

[@varun07ch67]

my bajaj icx7 induction heater's smd capacitor(numbering on pcb is C-102) has burnt so what is its value or what is its optional value.

[@CreativeWorldPro]

C-102 value = .001 uf/ 1kv

[@palaniaravind8663]

How many voltages for IGBT,tr8550,8050,and programme lc

[@Jerry-nd5vk]

Hanbao power HB 19A model induction stove. When turned on, power auto cut off in few seconds n panel power LED starts blinking. Tested IGBT, Rectifier fine. Replaced top sensor, high voltage capacitor 5 MFD 400V - No use. Pls advise...

[@CreativeWorldPro]

check the push button switch of induction cooker and 7805 voltage regulating IC

[@Beautyofsimplething]

What is the number of this microcontroller ic in this induction cooker

[@janvifikhrawat2501]

Mosfet replaced but no hesting and after some teime showing E9 error please suggest me i bajaj majesty induction cooker

[@sheshukumar8066]

Sir which type of courses to learn this repairing help me plz sir

[@CreativeWorldPro]

currently i don't know,,

[@gamesingh]

Iti electronics or diploma

[@AbinJames0]

hi, i have a prestige induction cooker. once it's fuse blown. I checked and replaced the damaged igbt and fuse. For two days it worked well, then same thing happened again, fuse blown!. This thing is happening over and over again. I'm almost gaveup changing IGBT. What to do? Please help

[@CreativeWorldPro]

you should check high voltage capacitor,,

[@vijaypatel1987]

Sir induction ko galti se 2 phase de diya hoo our induction chalu nahi ho raha hai usme kiya problam aa sakta hai,,

[@CreativeWorldPro]

2 phase matlab kya hai ?

[@dilipjain636]

440volt

[@varun07ch67]

plz tell the value of smd type capacitor(C 102) because it has totally damaged

[@CreativeWorldPro]

.001uf 1 KV

[@gomathinayagamsriram642]

What is the meaning of ic×7 in this electrical stove.

[@ilangovanNTK]

Hi brother I'm tamilnadu ... same model board only beep sounds not heating how to slow error e5 but preethy company

[@CreativeWorldPro]

you can check heating sensor

[@ilangovanNTK]

@@CreativeWorldPro heating Sensor change program ic change but not working

[@suraj9686]

Sir bajaj icx7 me supply ok karane ke baat heat play push ho Raha hai please suggest me

[@janardansingh8165]

गुड आइडिया टू रिपेयर इंडक्शन

[@c-maxkltec.supportchanaka1585]

Thank you very much i get some Idea

[@CreativeWorldPro]

Most welcome, thanks for watching

[@udayaswal]

Your Temperature Adjustment Button is not WORKING 😅 AFTER YOU FINISHED THE REPAIR JOB

[@palaniaravind8663]

What is reasons mostly IGBT short?

[@CreativeWorldPro]

any other parts damages may be the reason

[@AwaniG]

Sir my induction is taking long time to cook or boil anything. What is the problem?

[@CreativeWorldPro]

heating issue

[@rajkumarjangid4247]

SIR PRESTIGE PIC 20 YA PIGEON INDUCTION KAUN SA SAHI HE

[@SanjeevKumar-ce9wh]

Sir humare paas bajaj popular ace usme falt ye hain ki E0 lekh ke aa raha hain usme kya falt hoga Sir help

[@yaranagusrinivas7752]

Dear sir, induction stove wen give the supply less blow and off. What is the problem

[@yaranagusrinivas7752]

less wrong type

[@CreativeWorldPro]

you should change Induction Push Switch

[@CreativeWorldPro]

you should change Induction Push Switch

[@Khalid-ty8gf]

Can you plz tell me where I get indection parts ??

[@CreativeWorldPro]

Induction cooker repair shop or electronics component sells shop

[@Khalid-ty8gf]

@@CreativeWorldPro can u recommend me which place in dehli I should go

[@lionbiswas4510]

brother i want to contact with you????

[@dolanroy1997]

Sir Bajaj company ka induction ha mosfet change Kiya or sat 5uf capacitor change Kiya 2-5 minutes chalna ka bad mosfet kharap ho jata ha q? Pls help

[@CreativeWorldPro]

check the voltage on input leg of mosfet

[@dolanroy1997]

@@CreativeWorldPro 335vDc

[@CreativeWorldPro]

Bridge Rectifier check korasen ?

[@dolanroy1997]

@@CreativeWorldPro series Maha drim light jolraha ha pls

[@FuckYouGOD-tp8iu]

Same problem...did you solve it?

[@jino1403]

i have an induction cooker ......replaced faulty igbt...then the board is ok...but while connecting the coil ,the borad is short..i replaced with another coil...but it shows short again...what will i do?????

[@banwarilalyadav4717]

soldering हटाने के लिय सबसे आच्छा तरीका है फाईबर तुली(फाईबर राॅड़)की ब्रश बना कर ।यह इस प्रक्रिया मे जलता भी नही,परन्तु याद रखे फाईबर राॅड़ को हाथ या त्वचा पर घष॔ण ना करेे , क्यो की फाईबर की बारीक कण काटे की तरह चुभते व खुजली करते है।इस का soldering हटाने का कार्य अन्य soldering removing उपकरणों से सस्ता व आच्छा है।

[@dipeshmali1052]

Sir mera bhi bajaj ka induction hai jab me on karta to uska watts direct 2000 jata hai but fir kam nhi hota kya problem hoga plzz batao...

[@CreativeWorldPro]

konsa section per kam , nahi korta ?

[@dipeshmali1052]

Only 2000 par hi kam karta hai baki konsa bhi nahi kam hota hi nahi direct 2000

[@dipeshmali1052]

And sir kam bole to minus nhi hota

[@CreativeWorldPro]

mujha samajh aya,,upko induction cooker per push switch change karna parega

[@CreativeWorldPro]

mujha samajh aya,,upko induction cooker per push switch change karna parega

[@ashishtomar4635]

ICX3 ka circuit board kahan milega

[@ashishtomar4635]

Reply kare sir..🙏🙏

[@CreativeWorldPro]

please say in details

[@virendra2648]

The same kit sir , problem is IGBT &18V Zinear sorted Repeatedly please solve the problems sir

[@CreativeWorldPro]

check voltage

[@akshaybarge7175]

Hello sir, induction ke sub buttons continuesly blink ho rahe hai our beep-beep avaj aa rahi hai. Aur temperature bhi 140-160 change ho raha hai? In short buttons not working properly. Please give me solution on this. And please make video on this if possible.

[@CreativeWorldPro]

button problem, change button

[@er.saurabhkumar5374]

Mere induction jab on karte h touch krne pr current Marta h kya problem ho Sakta j

[@CreativeWorldPro]

kaha per current marta hain ?

[@mathewvarghese6180]

If we start some times it is getting on but some time not getting on .we doesn't found any loose connection.then what is the problem may timer get disturbed .it is Bajaj Majesty ICX PEARL

[@jackberi9584]

VERY GOOD VIDEO, THANX

[@CreativeWorldPro]

most welcome

[@tusharsunani4620]

mera....es mdl ka endctn...garam hotahe ..phir band hotahe fir chalu hota he..kya prbl he batana to..plz sir

[@topverma4522]

Good working sir

[@CreativeWorldPro]

So nice of you

[@sonuchaursiya4678]

Sir mera bajaj ka indetion icx neo h isme pwer aa raha h but heat nhi kr rha h

[@CreativeWorldPro]

change heatiing sensor

[@mohdriyazuddinnadwi9023]

I have bajaj induction. For some days after working some time when I reduce its temperature to no 3 it Stucks there and starting beaps. After that no button works. Please solve

[@devendrasingh8276]

I also have same problem, please make a video on this.

[@electronicss.rbangla7909]

Great sir

[@CreativeWorldPro]

thanks

[@adnansobh964]

ليزرية نوع البو بتعطي e2 شو العطل شكرا

[@eswaraneswaran7410]

சூப்பர் 👌 👌 👌 👌 👌

[@CreativeWorldPro]

thanks

[@dr.rahulpatidar937]

Induction par bartan rakhna par current aaraha hai..... Pls help me give suggestion

[@abhichauhan7422]

Sir is induction ka fault btaiye induction ruk ruk ke chal raha hai 2000 watt par bhi jese 300 watt par chalta hai

[@CreativeWorldPro]

what do you,,mean by ruk ruk ?

[@SAGGUSUMAN]

the same problem in my usha cookjoy please give any suggestion

[@ashishpanddyashish6207]

ViggcAbhi Chauhan

[@ranakumar8860]

Preset check Kare.

[@ranakumar8860]

Agar preset tik ho to 5 uf and. 3 uf condenser change Kare aur heat sensor check kare

[@RanjanKumar-ok3ox]

Sir mera Bajaj ka induction hai. Kabhi Kabhi E 1 problem batata hai.

[@CreativeWorldPro]

1st you should resolder

[@noorullau7434]

Sir, original IGBT kaha milega sir

[@CreativeWorldPro]

it is very rare to get original IGBT at the moment... you should collect it from Damaged PCB board of any Induction cooker

[@noorullau7434]

Ok sir , but now im do this way. But monthly near 100 pcs wanted for my service center.

[@CreativeWorldPro]

then you can supply this buying from local market

[@noorullau7434]

Creative World, all IGBT are duplicate, buy a local market new one and fix a pcb, it work 2second and it short. What to do

[@mobilizermahesh]

induction cooker igbt number h15r120... this place. can i use this igbt h25r120.. any problem?

[@CreativeWorldPro]

sure you can,,, you just check Emitter, Collector and Base

[@abdulakhan3561]

Please help me 7073563753

[@sweetsonsairem]

I found c3 short..is it ok?

[@CreativeWorldPro]

yes

[@sweetsonsairem]

I did replace the variable resistor with 1K it ok right? But after running for 1/2min the induction mosfet blows off what could be the problem? Thanking you in advance

[@CreativeWorldPro]

c3 was a zener diode... you should replace that

[@sweetsonsairem]

Can you tell me the value of that pls...

[@CreativeWorldPro]

Case - SOD 123 Short Description - (2.57-2.84) volt, 30 ohm, 20 mA, 350 mW

[@بچپن]

Maray pass same cooker hey koi err b nahi a raha only beep ki sound evry secount please wo kaysay thik ho ga

[@CreativeWorldPro]

which company is this ?

[@buddhadevdey5637]

Sir, I have bajaj mejesty induction but it is completely dead. But it's smps supply ok, 18v, 5v, DC output 324v, give suggestions. Thank you

[@sharatkhundrakpam959]

Sir.mera.pasbi.eisa.same.wala.induction.cokker.hai..power.input.samay.cable.fan.hi.chalta.hai.dusara.koinahin.kam.karte.kya.kharabi.hai.bataye.please

[@CreativeWorldPro]

you should check the Power Switch

[@rajeevta]

bajaj i c x 6 wov not power off after automatically set temparature. What may be the problef?

[@gurkiratvlogs3847]

Sir mere induction cooker me light nahi aa rahi he fuse igbt aur rectifier BHI Sahi he pls help me On nahi ho Raha he

[@CreativeWorldPro]

you should check the 5 volt of Panel Board...

[@dipankarbhattacharjee8024]

Sir mera Flipkart Billion ka touch induction hai. Woh achanak kam nehi kar raha hai. On karne se beep deke light blink kar raha hai lekin on nehi ho raha hai. Usko open karne ke baad hum test kiye the. Dekha ki sab me Tester phase dikha raha hai. Bridge rectifier ke +ve or -ve dono mein tester glow kar raha hai. Touch ka spring, fan ka do point sab mein phase hai. Kyase thik kare usko?

[@asifinamdar3786]

Sar ji mera yahi Bajaj Campania aur yahi modal ka induction hai display me koi error nahi aaraha hai sirf beef ki awaz aarahi hai induction heat nahi horaha hai please kya kare bataye aap

[@asifinamdar3786]

Display par 2.00 aaraha hai

[@antoniosidneyelias]

Ola como é feito a fonte deste fogão esta fonte é de quantos volt ??

[@rajeshkumarr.k822]

Kay bajaj ka upar ka bord nahi mil raha h sar Kay market se koi dusra bord lagaya ja sakta h

[@CreativeWorldPro]

upko market se dusra bord mil jaya ga,,,aap is board ka upayog kar sakate hain,,, thans,,a lot

[@vikashravi7865]

Are yr 5uf ka capistor change kro thik ho jyega

[@purvishaw2014]

My bajaj icx 8 plus is showing e3 error. How do i rectify it

[@CreativeWorldPro]

you should try changing heating sensor

[@purvishaw2014]

Creative World sir the error is abnormal voltage supply. Sensor changed no effect.

[@olusanyaabisoye3138]

My bajaj induction stove is displaying E7, what can be the problem?

[@AnilMaurya-cb8bx]

Sir Please. Make a vedio to replace the sencer diode .... Mean how to repair senser of a induction cooker

[@CreativeWorldPro]

okay

[@p10musicfactory28]

Creative World mera Induction ka on, off button kam kar raha hai par up down kam nahi karta aur 1500w me rahata aur bartan ko garam nahi karta aur awaj karta hai

[@CreativeWorldPro]

change the up down button,,of panel board

[@indiancitizen3408]

White line means negative not positive in a diode 13:00

[@javednahvi7637]

Dear Sir , my Bajaj induction IXC7 takes more time to heat things. rest it is fully operational.

[@CreativeWorldPro]

you should try changing high voltage capacitor,,,

[@SunilPatil-vr6yh]

Check 500 ohm priset

[@abhichauhan7422]

Sir jab hum induction ko 300 watt par chalate hai to wo kese chalta hai.

[@CreativeWorldPro]

it will supply very low heat,,,

[@vishnukumawat2056]

अगर हिंदी बोलना सीखोगे तो ज्यादा लाइक और ज्यादा सदस्य बनेंगे और इंग्लिश बोलोगे तो सदस्यों की संख्या कम होती जाएगी क्योंकि हिंदुस्तान हैं

[@vipindevraj]

Sir mere induction ka temperature control ka batan up and down kam nai kar raha hai..mai ne batan check kara sab thik hai....fir v kaam nai kar raha hai...sir kya problem ho sakta hai.....

[@tuduelectronicknd5786]

Problem-2ufAc-275v-40/105/21-pfisvastthenIthis-pf-re-place-ofterInductionishotvery-veryslow--somthingInductionhot--pleSethisfoulthow-Isolve -guidemeplease'-thankyou

[@rameshmeghta8770]

Sir r30 resistor value

[@CreativeWorldPro]

0.3 ohm

[@abidansari8874]

sir mera induction Barton rakhte his fuse uda details he sir help

[@CreativeWorldPro]

Check Rectifier Diode Or mosfet