🐝 Cricut Craze: 6 MUST-TRY crafts | Beginner Friendly

#cricut #cricutcrafts #beginnerfriendly
Hello everyone! A warm welcome to my channel! I'm absolutely thrilled that you have taken the time to tune in and watch this craft with me video I've prepared just for you. Get ready, get comfortable and indulge in some classic Cricut vinyl crafting! Don't forget to connect with me on Instagram for even more creative inspiration.
Sign
Bee Image - Canva
Font - Cherry Blossom
Sign
Sign - Hobby Lobby
Font - Malira
Sign
Sign - Michaels
Font - Cheesecake Sans
Tumbler
Tumbler - Hobby Lobby
Design - #M40F3D5FA
Tote
Tote - Hobby Lobby
All monograms were done using the monogram maker in design space
#cricut #cricutcrafts #beginnerfriendly

[@tamiegan6365]

The bee is cute and add a flower on the side.

[@DalyCreations]

Awe thank you!

[@dawnkukura3406]

… the bee kind is cute! if it bothers you (I honestly don’t think its bad!) … instead of doing all over, maybe take out that piece of cardstock, cut it down a tad, and put a piece of yellow (or any color) cardstock behind it - like a mat. 😊

[@DalyCreations]

Cute idea! Thank you

[@mlistander]

Brilliant idea using the pen for the dots!

[@DalyCreations]

Thank you! 😊

[@mlistander]

@@DalyCreations also I have been removing the dots before weeding and sticking them back one.

[@DalyCreations]

Oh okay! That's a good idea!!

[@maryweimer8207]

The bee doesn't look off at all. You are the only one who will see it. There is a way to put down transfer tape by folding back one edge to expose a sticky edge and place the exposed edge piece just outside of where you want the design. Then carefully pull the carrier sheet off from underneath as you gradually lay down the design. It works much better than exposing the entire back of the design

[@DalyCreations]

Thank you so much! I think I've seen that done before! I believe I tried it and I had hard time aligning it. Normally I do parchment paper and it usually works. Oh well, real life crafting... hahah gotta love it!

[@CassieslilCraftCorner]

You need a black light! It activates the glow in the dark. I have glow in the dark vinyl myself and my boyfriend, thank god for his 3D printing lol - used glow in the dark filament at one point and used the black light. Which I had to use it to find my glow in the dark iron on 😂😅 lol.

[@DalyCreations]

Hahaha 🤣 my husband has like 3 3D printers!!!

[@CassieslilCraftCorner]

@@DalyCreations oh wow! He should try glow in dark filament it’s awesome and it gives a good excuse to get a black light especially if the glow in the dark vinyl is white first 😅 i forgot your hubby has 3D printers lol

[@DalyCreations]

@@CassieslilCraftCorner actually I think he does have some! Not sure what he would make with it but I'm sure he can find something lol

[@CassieslilCraftCorner]

@@DalyCreations glow in the dark flowers for you and your daughter 😍🌼 I personally didn’t know black lights existed until he got glow in the dark filament 🤪

[@DalyCreations]

@@CassieslilCraftCorner oh cute idea! Thank you! I'll have to have him do some

[@sac4939]

All cute, love the floral iron on. TFS😊💕

[@DalyCreations]

Thank you! 😊

[@daisypage4551]

When you say print then cut are you meaning sticker vinyl or??? I just started using printable htv so maybe is skipped a step 🤷🏽‍♀️

[@DalyCreations]

The feature on Design Space is called Print then cut. The material I use is printable vinyl from Cricut

[@daisypage4551]

@@DalyCreations so I can just search printable vinyl and go from there?

[@DalyCreations]

www.amazon.com/dp/B0B25LS4X5?ref_=cm_sw_r_apann_dp_D0HR71JCDD1KYZK6YBVJ&starsLeft=1&skipTwisterOG=1 Here's an Amazon link. This is what I use. I hope it helps