Crosman 2260 strip down by Peas Productions

[@UnholyEJ]

Thanks to you I can resurrect my ole 2260 from 2011

[@BKPmax]

Thank you from Milwaukee. With your help, I added fresh seals to my old 2260

[@peasngravyproductions3728]

Fantastic if I can help one person I've done my job 🙂

[@heydoyourhomework]

Thank you for these delightful and informative videos on the 2260. They gave me the confidence to tear down my new airgun and fix the stupid valve face seal. Even the little detail about the breech screw upgrade to stainless steel saved me a big headache and I had one in hand to replace the braindead OEM Crosman .050 SAE Hex Key screw.

[@thisajim]

Can you make a video showing how to remove the stock/safety?

[@peasngravyproductions3728]

Will do next time one is in. No problem

[@raystone8113]

Hi do you service a 2260 Ratcatcher, and how much including repairs, upgrades and tuning please. Many Thanks. Ray

[@peasngravyproductions3728]

Yeh Ray, I can service and repair also tune, what's wrong with it ?

[@raystone8113]

@@peasngravyproductions3728 the CO2 cylinder was stuck inside the gun so my grandson decided to hit the cylinder in the base with a sharp screwdriver and pushed it further inside the gun!!! So I’m not sure of the damage . Many thanks. Ray

[@peasngravyproductions3728]

Ouch... until I get the patient on the bench I won't know what's damaged and what's replaceable

[@raystone8113]

@@peasngravyproductions3728 ok I’ll send it to you and you can decide what it needs, can you send me address please. Thanks. Ray

[@peasngravyproductions3728]

Hi Ray I can't post address or phone numbers it gets removed for some strange reason are you on Facebook or mewe?

[@peasngravyproductions3728]

You rotate the safety half way and use a punch and just tap it through. The safety should pop out the other side. I will make a new video just too show this. Hope you can understand my description

[@peasngravyproductions3728]

Please to have been helpful. If i can help one person ive done my job. Thanks

[@markrobinson2533]

Can I contact you in regards to converting a crossman 2250xl onto hpa please Thanks Mark.

[@peasngravyproductions3728]

@@markrobinson2533 yes no problem post your email address once I've seen it I'll delete it

[@00kingi]

How much do you charge for a tune/ repair?

[@peasngravyproductions3728]

Depends on level of tune whether you just send the valve or you want your barrel and tp modded at the same time. A valve tune on its own is 15 including return postage if you send your tube with the valve I'll pin it for an extra 5ver as its only a 2min job. And as for repairs yes I under take repairs but I can't price unless I know what the repair is.

[@00kingi]

@@peasngravyproductions3728 I think mine is missing a part or 2. It was given to me a trade. I’ve given it a once over but I think it would benefit your going over. Do you have an email address?

[@peasngravyproductions3728]

[e-mail]

[@andrewarmstrong8651]

How do you remove the safety catch

[@peasngravyproductions3728]

There's a slot behind the trigger blade, inside is a small wire/spring, use a pick to pull the wire toward the trigger blade, the safety button will then push out and the trigger will pass through the stock.

[@andrewarmstrong8651]

Peasngravy Productions thankyou for your quick response sorted cheers

[@peasngravyproductions3728]

No problem glad to help

[@lukewhite9750]

How can I remove the stock please

[@peasngravyproductions3728]

On which rifle Luke?

[@AlexSmith-bx3lt]

Well, I went to go disassemble, but when I got to the chamber, I didn't have a Allen wrench small enough🤣 I'm trying to fix a part in my friend's gun

[@peasngravyproductions3728]

It's imperial 50thou is what you want. Here is a link to the ones I use www.ebay.co.uk/itm/161596334329

[@G_Wood-23]

@@peasngravyproductions3728do you have a link for the replacement screw? Ideally flat head like mentioned in the video. Can’t find one in stock anywhere. Thanks for the useful video 👍🏼

[@peasngravyproductions3728]

@@G_Wood-23 search for "crosman screw" on that well know auction site

[@peasngravyproductions3728]

www.ebay.co.uk/itm/154129317502

[@Randolino]

too bad you don't show how to remove the safety, thus I cannot remove the stock. Oh well.

[@Randolino]

I got it finally