John Deere 1020

Kyle McElfresh wanted a review! Thanks Kyle !

[@geraldosteen2357]

Thanks for sharing Scott. I appreciate your vids. You guys are awesome.

[@gleanerk]

Thanks man👍🏻

[@rustyoldjunk]

Nice little tractor. I helped with tobacco one summer when I was young. The guy had about 10 acres of it. Mostly all hand work with that stuff.

[@gleanerk]

Yes it was some hard hot work ! Thanks for watching and commenting my friend Mike !

[@jankotze1959]

Great review , we had some of these many years ago. 1020's, 2020, 3010's

[@gleanerk]

Jan Kotze Thanks for commenting,and sorry for the delay.

[@outcastprojects6733]

Nice old tractor, I am always amazed at how similar the old jhon Deere tractors are to my rough terrain 480b jhon Deere forklift. I think they even run the same transmission.

[@gleanerk]

chris richards Thanks man for dropping by and commenting. Yes they are very similar.

[@Masseydriver]

Nice job on the overview Scotty. That's a mighty little tractor you have there.

[@gleanerk]

Massey1105driver Thanks massey

[@PeterbiltBoy359-Kyle]

thanks Scotty man I enjoyed it man appreciate it catch you later man loved knowing the history of the little 1020 can't wait till you do more work with her 😀 Thanks again

[@gleanerk]

I'm glad you enjoyed it !!!!! Have a great day my friend!

[@PeterbiltBoy359-Kyle]

ScottyRockTrains. you to take care

[@jameslcoble248]

Thought I'd look back at this video. Go my eyes on a John Deere 1020 and John Deere 830 i think. May look at them this weekend. One has a loader. Any known issues or things to look for?

[@gleanerk]

Check the oils , look it over, give it a drive around and make your decision. They are very well made tractors .

[@lynnhavenfarm8514]

Nice little tractor only john deere I've put time on was a 4430 but wouldn't mind trying a 3020

[@gleanerk]

lynnhaven farm kzbin.info/www/bejne/Z5iVpoyfjLV1m7M has a 3020 if you’re interested. Right now that’s the only tractor. Thanks for dropping by watching and commenting friend! I appreciate it !

[@carrollmccoun110]

Good tractor. They are high dollar down in Mississippi.

[@gleanerk]

Sorry for the delay in responding but thank you friend. They not cheap here either!

[@banditfarmer1900]

I didn't realize the 1020 was so close to the horse power of a 2010 , But the 2010 had its problems so I guess it replaced it. I would like to someday have one myself but for now I'll use what I got. Thanks for posting this one cousin Scotty ! Cousin Bandit

[@gleanerk]

Bandit farmer Thanks cousin Bandit! They are really handy tractors as you have seen in past videos! This one has a tad more power but not so to hurt it ! As always I enjoyed talking with you!

[@chuckstevenson2929]

Thanks for the walk-around Scotty. Do ya'll an all keep a fire extinguisher on your machines?

[@gleanerk]

Chuck Stevenson No on tractor but have n combine. Something to consider though!

[@jankotze1959]

That's a nice tractor Scotty, we had one many many years ago, nice video

[@macfarms]

Love the older gear. Thanks for the vid.

[@gleanerk]

Mac102004 Farms Thanks Mac for dropping by and commenting friend!

[@nickmurphy3935]

Any chance you have a parts book? Trying to find a part number for a 3” round flywheel inspection cover , throwing Hail Marys out here 😂

[@gleanerk]

I don’t have a book but will look behind and see if there b a number tomorrow. Between job and getting together my old irrigation system up and running I totally forgot you asked me this . I’m so sorry for my tardiness friend .

[@nickmurphy3935]

@@gleanerk no prob thanks so much !

[@aaronforestier7260]

I recently acquired a John Deere 1020 ,do you have a video on how to change a fuel filter?

[@gleanerk]

kzbin.info/www/bejne/lXalaGWim82sh9k My cousin Soybean Farmer has one

[@gleanerk]

He take his off of engine due to location, but on a 1020 you don’t have to. Hope that helps

[@duncang01]

I have a 69 1020. I love the old tractor

[@gleanerk]

duncang01 You’ll have to show us your 1020 one day, thanks for watching and commenting friend !

[@ethanschroeder9531]

Can you show how to change the hydraulic fluid and filter on this 1020?

[@gleanerk]

I’m not able to do at this time but if you’ll put a 5 gallon bucket under the filter ,take a wrench and loosen the filter housing let oil drain ,finish unscrewing the filter off ,take old filter out replace with new filter , replace large o ring ( observe how the old one is on ) , I always put oil on o ring . The tricky part is getting it back all together with o ring not pinching, I usually push up on filter housing while turning to secure o ring tight against tractor.tighten it up, crank up tractor and see if it’s leaking anywhere around filter. If so you’ll need to take off and do the same procedure again. No leaks you are successful replace oil . I hope you’re ok with explaining it to you. It’s really not that hard if you’ll follow what I said . Hey I’ve screwed up in the past and had a leak ,redid it and it preformed well . Thanks and Merry Christmas Ethan. I wish I was there to help you.

[@WilloughbyDroneTracking]

Question. When hooking up the draw bar what pin is needed to secure the front part to the housing? So it can’t slide out.

[@gleanerk]

WilloBeastin Hey, tractor in the shop getting a head gasket repair or I’d show you. Will look in my shop this afternoon after work for my back up pin I have and will try to video it for you . The pin is about 3 inches long by 1 inch thick and uses a pin to hold in .

[@gleanerk]

Sorry, but I don’t know where I put the extra pin to show you what it looks like.

[@michaelc9128]

Sorry to post on an old thread,do you still have this tractor

[@gleanerk]

Yes , family heir loom

[@jakeziegler599]

Good info scotty! Have u had a chance to try ur drill out yet

[@gleanerk]

Jake Ziegler No not yet !

[@SoybeanFarmer3300]

cousin, excellent work collecting the data and presenting it. nice camera work..... :)

[@gleanerk]

Soybean Farmer Thanks SF

[@JacksonJohnson-jv7rn]

Nice tractor

[@michiganfarming1955]

nice little tractor, im still sticking with my ihs lol

[@gleanerk]

Michigan Farming I like them too!

[@amathonn]

Is that the hydraulic fill port on back by rockshaft?

[@gleanerk]

Andrew D Behind the seat on the rock shaft . Just above where top link connects

[@WilloughbyDroneTracking]

Do you have 2 batteries in the tractor? Mine does and wondering why

[@gleanerk]

WilloBeastin Just one 12 volt. They came with two though . If you live northern area you might want two . They kinda cold nature

[@NorthEastOhio]

that's a beautiful tractor

[@gleanerk]

North east Ohio farmer Why thank you fellow!

[@ethanslife4206]

Hello, like the vid it is very nice keep em up!

[@gleanerk]

Life out here in the country Ok , thanks for commenting!

[@ethanslife4206]

Hey no problem it is what I can do for a subscriber go share the word about my channel

[@kibetbernard4984]

Nice machine

[@gleanerk]

Thanks Kibet

[@WhoDat-cc8zo]

Love the 1020

[@gleanerk]

Who Dat3020 She in the shop right now getting a head gasket repair. Like you said in your video , the 20 series were good tractors ! Hey thanks for dropping by watching and commenting.

[@PeterbiltBoy359-Kyle]

my neighbor has one to I will try to get some videos of his sometime looks identical to yours his is a 66 two cuz Scotty he will love to know the information he has had his since he was 13 like I said I will try to get a video of it and tell him to tell the story of his

[@gleanerk]

Kyle McElfresh Ok , sounds good Kyle .

[@PeterbiltBoy359-Kyle]

his story is pretty cool too my buddy's name is Pat his has the gas motor

[@gleanerk]

Kyle McElfresh Ok Kyle , look forward to hearing about it !

[@kibetbernard4984]

I Need one please

[@gleanerk]

What a 1020 ? They’re around.

[@farmingforfunandprofit940]

Wouldn't know anything about flue cured tobacco..........or sleds or stringing or shooting it up in the barn...or lets not forget...."crapping".....Sand lugs

[@gleanerk]

David Goethe xxx From 4 years old till the year 2000 . Spring summer n fall of my life! How about you ?