Step by Step, Construction of Efficient Current Balun 1:1 Toroid FT-240-43, AWG18 Stranded Wire.
Пікірлер: 47
@ea3fa2 жыл бұрын
Felicidades por un vídeo sencillo y clarificador.
@TEGEscalator3 жыл бұрын
Great vidéo , greetings from Belgium 73 👍
@EugenioGuarente3 жыл бұрын
TNX, 73..
@322doug Жыл бұрын
EXCELLENT DEMO , THANKS NS9T.
@beltranhernandez19534 жыл бұрын
Excelente video, gracias por compartirlo, con los amigos radioaficinado
@yv5emghamradio2494 жыл бұрын
Gracias Beltrán. 73.
@pleasetryme Жыл бұрын
if i study this correctly count the red wires has 11 turns and the other has 10
@dannystephenson49572 жыл бұрын
Could I use 1.5mm copper enameled wire?
@juliocesarpereira43253 жыл бұрын
Thanks a lot. 73!
@yv5emghamradio2493 жыл бұрын
TNX, 73
@imken23923 жыл бұрын
Is this Balun used only for dipoles? Is one needed for a beam antenna say something like a single band 3 element yagi with a gamma match, matched to the center freq of the band (10 Meters)? The yagi's driven element is basically a rotatable dipole.
@yv5emghamradio2493 жыл бұрын
Yes!.. it works with any Antenna, remember, you need for a perfect match, 2 elements that connects your antenna with your radio.. a Impedance coupler.. and a Common Mode Current supressor.. in case, your antenna it's a symmetrical antenna , like a Dipole, you need only one 1:1 Balun like this, .. but if the antenna , needs, another impedance relation, like 4:1, 9:1, etc... , You need 2 Baluns.. The Impedance Match, and the Common mode Current noise supressor..
@LBJ-bj2 жыл бұрын
hi is all 1:1 Current balun 12turns each side? or it depend on the toroid size ,Thanks 73
@ernestotekhaus38184 жыл бұрын
Excelente amigo. Saludos al Gato :)
@yv5emghamradio2494 жыл бұрын
Retornados y Gracias!.
@imken23923 жыл бұрын
Is the 32" wire length important other than having enough to finish the wraps? Also is the length of the wires at each finished end important. I made 2 after I watched this. They both give different readings on the10 meter dipole. I used the same torroid and the same wires as in the video. Tested with my RigExpert AA-600 and the Icom 756 pro III.
@yv5emghamradio2493 жыл бұрын
I Ken, ..the initial length of the wires for making the Balun, are not important, only for avoid the mess with long wires... But., try to keep the finished ends, wrapped and no longer of 2 inches.. Try to keep the wire, equally spaced on each turn and very tight to the Core.. It's almost impossible to make, to Baluns exactly equal., 73
@brandonlaragirl Жыл бұрын
What do you think about that analyzer you mentioned. I'm looking into getting one. Has it turned out to be what you expected? Thanks in advance, 73s
@HughJarse1968 Жыл бұрын
Does it have to be exactly 12 turns? My wire must be a bit too thick, I can only get 10 turns on the ferrite core - is this enough? Many thanks for any comments & help :)
@theroguetomato53628 ай бұрын
Same here. I wish someone with know-how would answer this. In the meantime, I'm going to try different wire to get 12 full turns.
@arconeagain2 жыл бұрын
I take it 16AWG is okay?
@balasubramanyancp8822 жыл бұрын
What type of torroid used? Type #?
@imken23922 жыл бұрын
By stacking cores to increase the power handling capability, Say 2 cores for 500 watts or more, would the wire size need to be increased as well?
@N1SEP- Жыл бұрын
no, stay with 18AWG, but maybe use PTFE wire, much better heat rated
@luisradaelli56914 жыл бұрын
muy bueno colega, se puede hacer uno con núcleo al aire y tubo pvc?
@yv5emghamradio2494 жыл бұрын
No de este tipo o configuración, los Choke Balun de "Aire" con tubos PVC, son totalmente diferentes, poseen un rango de atenuación de la Corriente de modo común, mucho más "leve". y no son tan eficientes, como uno con núcleo de Ferrita.
@kanaiyalalkotak26382 жыл бұрын
After completion of wire wrapped what Next ???
@user-iu7eu3vr1o2 жыл бұрын
Power?
@pa9x3 жыл бұрын
Nice demonstration! For what maximum power do you rate this balun?
@yv5emghamradio2493 жыл бұрын
With this Toroid, easy 300 Watts nominal, and 500w peak, (only few seconds).
@pa9x3 жыл бұрын
@@yv5emghamradio249 ok, tnx!
@PY4SR3 жыл бұрын
I believe the designer of this balun, Wolfgang Wippermann DG0SA, rated it to 800w. FT240-43 as core. The isolation must be PTFE and the wire 18AWG, silver plated. 73
@michaeldavidson99397 ай бұрын
Couldn't get through the video because of the obnoxious background noise (soundtrack).
@matthewlee26867 ай бұрын
@@michaeldavidson9939stop bitchin they make a volume and mute button for a reason.
@kissingbanditt4 жыл бұрын
Which side goes to coax? Or it doesnt matter?
@yv5emghamradio2494 жыл бұрын
Each side works the same In or Out, and you can put the centre of Coaxial cable in the whatever color you want, and the shield on the other. In the same side off course. 73.
@user-uw7os9zr5b Жыл бұрын
THAT'S FOR SURE 1:1?
@EA3FNI3 жыл бұрын
¿QUE RANGO DE FRECUENCIAS CUBRE? DE 1.3 A 10 MHZ
@EugenioGuarente3 жыл бұрын
Si.. de 160 a 10 mts.. , 300 watt continuos.. con ese Toroide
@ea3fa2 жыл бұрын
@@EugenioGuarente Se podría cubrir de 1,8 a 50Mhz con la misma configuración?? En caso que NO, qué cambios serían necesarios?? Gracias !!
@hermantowers3 жыл бұрын
73
@TheAdrenaline852 жыл бұрын
The videos I’ve been seeing on YT don’t help a novice beginner. I’d hoped they would.
@alexalonso20934 жыл бұрын
ty for showing us how to step by step too many hams go to fast .and we need step by step ty plz show us more how to connect to anntennas 7 3
@yv5emghamradio2494 жыл бұрын
Sure, In the next video, I will show how to put on a plastic case, with the female so239 connector, and the two antenna terminals, and on a 3rd video, the implementation on the complete Dipole. 73..
@Joe_KS1I3 жыл бұрын
I'm curious, why FT240-43 and not -31?
@gravestonemyth2 жыл бұрын
Same here. I know the 31 mix is preferred for coax-type current baluns.
@W-733_KWX Жыл бұрын
Same on my side, 31 mix is better for 1:1 to remove RFI (common mode). For efhw mix 43 is prefered.