Since Cleetus and James have the MTN DEW & BUSCH wraps, respectively. You guys def have to do a TWISTED TEA wrap. 100%
@Toxic880882 жыл бұрын
It would be monster - VTEC wrap cuz Kyle.
@seankelly82252 жыл бұрын
Coca-Cola pfi wrap
@noneyabusiness13592 жыл бұрын
Baja Blast
@bangthemgears99992 жыл бұрын
They ain’t getting paid for the promo, not sure why they even did it to begin with. I would do boostedboiz wrap all over it. F the free sponsorship
@brandonbritt992 жыл бұрын
twisted tea wrap 1,000 %
@Danger-Dave2 жыл бұрын
I'd cut out the thin top and sides of those floor frame channels an inch or 2 longer than the mounts, then drop in some solid billet rectangles the thickness/size of the OG brace. Weld em in place then tap into the thick stuff like you had mentioned... Easy Peasy and much more solid transfer of energy to the bottom and less chance of vibration issues / weld fractures.
@ericmichels88432 жыл бұрын
Kyle, you can always install nutzerts into boat frame. Just use plated ones not stainless because stainless will make aluminum oxidize way faster than just regular steel.
@Skwisgar23222 жыл бұрын
Good old galvanic series.
@joshua_J2 жыл бұрын
Please more people like this so Kyle sees it
@mikeyalwayslikesit2 жыл бұрын
#facts
@leadfoot85932 жыл бұрын
Is cutting mounts out of al and welding them in a bad thing?
@scotttod69542 жыл бұрын
He could just fish the bolts in and face them up. They make wires that are wound the same thread pitch for bolts then you just pull the wire though and pull the bolt in. I have installed a bunch of 5th wheel hitches and the kits come with the wires to fish bolts into frame members.
@dragonflyjoyride2 жыл бұрын
Nice little update! Hope the jet boat get a good wrap put on her like the Cleetus boys. I think you should keep the same theme and do a Twisted Monster. Keep on build and turning wrenches. ✌🏼
@3SM20Pilot2 жыл бұрын
You can still put in the aluminum blocks. Just cut holes and recess them. Then use a sacrificial anode as others suggested along with a lot of anti-sneeze on the bolts. Making sure the block is thick enough so the bolts don't have a hole at the bottom would help too.
@04ninjazx10rr2 жыл бұрын
Dyslexia 4:17. Cainted the page. Love it. I have the same affliction.
@Eschelonistic2 жыл бұрын
Hyumdai excel pump is the most used for LS setups, you need to just strap or weld on some hold points for the driveshaft on the van, you're fighting the torque so hold is back.
@FastLaneLyfe2 жыл бұрын
Congratulations on the baby Wyatt! I hear you having a son too. Dang you and Kyle must have found twins.
@RubbishFPS2 жыл бұрын
They adopted a child of their own...
@andwooo94602 жыл бұрын
Ha 😂
@ahfreebird2 жыл бұрын
@@RubbishFPS Get ready for the diesel Hondas in about 15 years!
@i-_-am-_-g14672 жыл бұрын
@@ahfreebirdnah its gonna be the future remember... tesla swaps inbound
@dj_ps_gamer13242 жыл бұрын
😂😂😂😂😂
@anthonyestevez1182 жыл бұрын
Great stuff BOIZ! Can't wait to see the Rowdyssey trolling the streets! Wyatt's truck is looking sweet! The boat is coming together nicely! Thanks for sharing BOIZ!
@garrettbinley73492 жыл бұрын
Hoping you read this..,Scatter-shield !!! For the jetboat! That exposed flywheel/driveshaft is a little sketch. I’d also put a carbon steel plate beneath that rotating assembly to keep it from punching a hole in the hull if it comes apart.
@rbyikes2 жыл бұрын
McMaster Carr has rivnuts that you can put in the aluminum, to have some legit threads in that aluminum. Give you something really substantial to mount that engine to. Boat looks SIC though!!
@gerrymilidantri64572 жыл бұрын
You guys really engineer your projects well. !
@Scottyschannelmtb2 жыл бұрын
Don’t mess about just whack a spooley boy on there for the maiden voyage love it dudes 👊🏻🤘🏻👌🏻❤️🇬🇧
@DaftFader2 жыл бұрын
"I'm gonna put this e85 on the passenger seat" precedes to litterally poor e85 onto the seat. 🤣
@Koop2k2 жыл бұрын
Kyle, please put some stock flywheel bolts in those other holes.
@00xYamahaRacer2 жыл бұрын
Universal driveshaft is awesome, last year a company driver needed a driveshaft done like asap and they got it done.
@soarinsoarer12 жыл бұрын
Kyle you were talking about the mounts .. even if you put a 1/8 " thick alloy plate under the steel it will help ... just like your roll cage mount plates .. and it can be a sacrificial plate so you dont damage the boat rails .. this boatis goi t to be mental ...
@djrisberg2 жыл бұрын
Put a hydraulic fluid accumulator in the truck power steering high pressure side...when the electric pump can’t keep up, the spring in the accumulator will compensate...adds safety too as backup pressure for hydroboost brakes.
@THCv32 жыл бұрын
Kyle is getting married, bet.
@kylebrace99492 жыл бұрын
Can’t wait to see the truck all done
@yankey42 жыл бұрын
Love it! Thanks for sharing. No clue if this would work or not to hold that K in place. There is a thing called a rivnut. Maybe that would work. Thanks for the videos man. It's nice to see some coom stuff and just take a brake for a hard few weeks. Much love. God Bless.
@fncrazy1012 жыл бұрын
Absolutely love how you have a Porsche daily! You have talked about having a Porsche years ago, and now you have your baby! So happy for your success 👊🏼
@liaml71992 жыл бұрын
What baby are you talking about? 🧐
@sprindustrieztz10152 жыл бұрын
You could weld some blocks either side of the mount then fabricate a cradle that goes over the mounts
@brandonbritt992 жыл бұрын
wyatts the real mvp cant wait for the truck to come to life
@dandel3512 жыл бұрын
My question about the K swap in the jet boat is , How do you do an oil change on it ? Is the sump plug pointing at the hull ? If the drain plug is on the side how would catch the oil ? Hope it all works out great that boat is going to be a fun little ripper once it's done can't wait to see it in the water.🚤😄👌
@eldonerc25242 жыл бұрын
Hell probably use a suction pump an just pull it out. Never be able to get a catch pan under it anyway.
@stevereinhart40672 жыл бұрын
Could put thread certs in the aluminum to hold down the mounts.
@bobbymiller29552 жыл бұрын
Use a Chrysler style piñon snubber.. keep diff from turning up.. 60s tech can help
@banditgrizzy19552 жыл бұрын
🤔 since the dif force is up... put a brace or bracket with a bumperstop on top side of the dif 😉👍
@wobblysauce2 жыл бұрын
With the engine mounts on the jet boat, you can still do a sandwich plate.
@ericcerra32682 жыл бұрын
hell yes i can’t wait to see it rip on the water
@mikellewis23462 жыл бұрын
Dont mader how you build your jet boat, long as your building it it's right for your boat. Keep up the great work 💪
@MrSupermugen2 жыл бұрын
If your tapping where your mounting the Engine mounts, either use 4 massive bolts to increase thread interface or run 5 smaller bolts, two on the inside and 3 on the outside.
@eldonerc25242 жыл бұрын
An use a fine thread bolt to get more thread engagement.
@Pinky.15232 жыл бұрын
That thing has to make some sweet turbo noises!!!
@Smokey720132 жыл бұрын
I think you will be putting a softer bushing in your mounts on 1 side at least.
@Fackler912 жыл бұрын
Are you going to set the oil pan of the jet boat up so you can use a vacuum pump to change the oil. Like weld a bung on the front with a valve/nipple. Then just connect a tube to it and vacuum it out. Just a thought
@Endlessfirerain2 жыл бұрын
I'm betting there's a new lady in your life
@fallenhobbit65542 жыл бұрын
has been for awhile. I saw her in the background at a few events
@alfredlownii80112 жыл бұрын
With your mounting you should fish in nut plates. And not worry about pulling threads out.
@andrewmantonya8502 жыл бұрын
Awesome job guys.
@ianellertson49632 жыл бұрын
Glad to see you Two wearing seat belts! We kinda wanna see you around for a while!
@BandWidthExpired2 жыл бұрын
Why not make the BOAT SIDE OF THE MOTOR MOUNTS out of Aluminum then weld them to the boat???? This thing will be INSANE! cant wait to see it on the river!
@jdshanahan42152 жыл бұрын
Would be cool to see the porsche wrapped.
@theenglishgentleman37162 жыл бұрын
Just fed a nut plate up the rail towards to engine mount, bolt up then rivet in position to hold the plate while removing the bolts.
@jayrodz31222 жыл бұрын
Can't wait till Wyatt's truck is done and the J 🚣 boat the van sounds amazing 👍
@tannerhoffart98212 жыл бұрын
Could even take a piece of thicker al. And tap it then fish it in from the cut out and pinch the rail
@davidfortner60992 жыл бұрын
I love the Corvette guy can’t wait to see what y’all do with it
@TorchFpv2 жыл бұрын
Put riv nuts in to the hull to bolt the motor in or the aluminum threads will just pull out for sure..
@pharris492 жыл бұрын
Kyle and Wyatt look at a rack from a 2020 f150 it's all electronic. It will also cut down some weight. Keep it up y'all are awesome.
@koburz2 жыл бұрын
We need a " cainting the page" shirt!
@whiterhino79192 жыл бұрын
You should run the alternator off the drive shaft flange. Right diameter pulley machined to sandwich would make it easy to tuck the alternator over the jet drive and you'd only loose maybe an 1/8 of slip in the shaft
@Madams952 жыл бұрын
you should get some zinc for the boat. you should protect it from electrolysis. expensive electronics to let it get destroyed from pesky water electricity! also, whats the plan for cooling???
@swealer2 жыл бұрын
Wyatt, the Ackermann Winkel (Ackermann Angle) from the steering looks off. I know the truck isn't aligned but it shouldn't look this off. Hit me up if you need some tips. Greets from 🇩🇪
@ScrimpyZex2 жыл бұрын
“Since i cainted the page” 🤣🤣🤣 @4:16
@Taco-Mike2 жыл бұрын
Hopefully you guys put alot of heat wrap and lining on those backseats lol
@xnorcal831x2 жыл бұрын
Just watch soon you will be posting a video with the title. "Jet boat with 2 step." Would love to see it set up like Mike Finnegan. You need him to help you.
@anythingandeverything77332 жыл бұрын
I think my favorite part about seeing any roundcy videos is watching the dust fly around every video🤣
@Taintlessdisc2 жыл бұрын
Gonna have to get the jet boat painted to match the rowdessy lol
@pgmurray762 жыл бұрын
6:34 That up boost sequence made me laugh too. THAT was rowdy.
@BenjySparky2 жыл бұрын
Kyle and Wyatt y'all rock! Love the channel and content! I'm here for the algorithm! Peace
@jasonhuber32362 жыл бұрын
I am very very curious how you plan on draining the oil out. There's like no room. You can either A- cut an access door from underneath and make it waterproof. B- dry sump system. C- just suck it out through the dipstick tube like how Audi dealers do it.
@stunessa12 жыл бұрын
c, as done with most boats
@BassManBobBassCovers2 жыл бұрын
So many things to be stoked about holy shit!!! 😍😍😍😍😍😍😍😍😍😍
@MrMadkaw4002 жыл бұрын
Little red corvette
@CodeBuildsCars2 жыл бұрын
The boat is gonna be sick
@MrMarkb682 жыл бұрын
It's not too late to add more material to attach the engine mounts to. Better safe than sorry.
@texasworton99552 жыл бұрын
Would be so cool if they put a boostedboiz rap over the whole minivan that would be awesome
@miguelplaza6582 жыл бұрын
VTEC in the water 👍💪👌👌
@nonamemcgee12952 жыл бұрын
tavarish building a hellcat minivan, better get that record quick so chumps know who's first to the soccer game 👑
@landis1812 жыл бұрын
Just an idea but cheap silcone sheets cut to shape of the mounts would help with noise as well :)
@capnslufox2 жыл бұрын
Yes, I got to start with a Honda commercial!
@aroncharlwood17772 жыл бұрын
Just use some welded in round threaded inserts to beef up where the engine mounts bolt in problem solved.or cut out the plate under the mount and weld in some 3/4 plate flush in that spot
@mehmetonat86852 жыл бұрын
Caited the page!!!she must be flying🤣🤣🤣🤣🤣🤣🤣🤣
@atowns33642 жыл бұрын
Going to be a monster! Rip Hull structure🤣
@shawnjacks20722 жыл бұрын
00:10 what a teaser
@chadbanks76112 жыл бұрын
I think you guys should just shorten that seat on the left chop it and then to reweld it shorter and instead of modifying that header but you guys know best love the video keep them coming can't wait to see the Duramax going down the strip
@jonmmarquis7772 жыл бұрын
I can see a future video... "K swap boat anchor" when the engine let's loose** 😆 Just a fun way of saying... if you have to question it. build it stronger. Nice work man can't hate. Just want y'all to be successful and see some k swap river jumps!!
@minilurk112 жыл бұрын
Please start a series of racing random people in the van lol
@bartman36082 жыл бұрын
Kyle "cainted the page" LOL. 4:17
@RetirementFund7502 жыл бұрын
Why don’t you run nutserts? They would hold way better than just tapping the aluminum and you could just run a thin strip of rubber in between the mount and the body and that would make it not be metal on aluminum and would help with dampening.
@wizord74602 жыл бұрын
you know what Boat stands for... Bust Out Another Thousand
@matt3x372 жыл бұрын
You could just put a manual steering box on it Wyatt they work great we just put one on my 78 omega and what a difference it made
@eldonerc25242 жыл бұрын
Still be tough with those big ass meats. An he probably doesn't want to turn it a million times to go lock to lock. 😂 Wonder how well an electric setup would do then use the pump to run his hydroboost on the breaks.
@jonathanstaley95222 жыл бұрын
You'll need a pretty big fuel tank which will add even more weight. Hopefully it'll work out fine :-)
@theshed11682 жыл бұрын
Get some stainless steel rivnuts to bolt your engine mounts down with
@kensmart54002 жыл бұрын
So awesome!
@The50Baker2 жыл бұрын
That jetboat is gonna be the best one out of all your buddies! You putting a turbo on it?
@MellowYe77ow2 жыл бұрын
It'll be N/A for now. Turbo is planned later.
@ClaytonF102 жыл бұрын
Use nut zerts to mount the engine instead of tapping
@wickedeagans2 жыл бұрын
Klye ur killing me bro. Gotta stop shitting the door by the glass. On cars without door window frame will start to leak and window will wobble if keep shutting doors pushing on window. Especially pushing on the corner where has the less amount of support. Sick to see the old soccer mobile out🤘🏻
@DeeIsland2 жыл бұрын
VTEC on? Because, correct me if I'm wrong, but I think the MR2 tune probably doesn't have it since it's locked into VTEC.
@reneescouch90352 жыл бұрын
Whose corvette is that???? Are we finally getting some LS action?
@ptorlina2 жыл бұрын
You said don't worry but I am. If you can put a non metal gasket between 2 dissimilar metals I would, I live and work on boats in Salt water.
@williamhodge71932 жыл бұрын
Cant wait for more of the duramax and jet boat build
@kadeno842 жыл бұрын
4:17 cainted the page 😂
@TacBFU2 жыл бұрын
He can do a series on how to install a baby seat kirkey. He can rename the van the rowdy mommy van. Boosted daddy..... boosted baby.....
@fixitwithfire64302 жыл бұрын
Oof. Galvanic corrosion is real Kyle. Might wanna do some research.
@pgmurray762 жыл бұрын
4:09 Open the doors. Leaf blower.
@meshlol2 жыл бұрын
punch out those motor mounts in cad and find someone with a 3 axis to punch them out of a block of billet and weld them to the hull.
@brettfriesen89732 жыл бұрын
Pretty sure the u joints on that drive shaft aren't clocked correctly. They need to be opposite of each other
@kudapadi692 жыл бұрын
just casually said "cainted the page" lol 🤣
@Unlaced_kickz2 жыл бұрын
Unlike 3rd Kyle finally found the hole 🕳
@TheBCninja2 жыл бұрын
Oh man please make a whole video of the van hurting feelings in "mexico"
@RayTrent012 жыл бұрын
Lol Kyle said since I cainted the page lol instead of painted the cage 😂😂😂
@paulezay35992 жыл бұрын
Is that a Corvette in the background I think I see a ls power plant coming to the boostedboiz channel