How To Replace a Citroen C1 Exhaust System & Peugeot 107 & Toyota Aygo

[@CycloneCyd]

📌 LED conversions for Citroen C1 lights: kzbin.info/aero/PLOaePmzqZNJ2hcW4Lx0vSrRM2HCHcUmUW

[@volt8684]

You are very soothing to watch. I get proper anxiety as an amateur but have used your vlogs on my daughters 1.0 yaris. I did the pcv, throttle body and map at the weekend. The throttle body was water cooled electronic one, not cable. Was a swine to get cooling pipes off but with your vlog I had confidence to clean all the parts and reassemble. Hopefully the oil consumption will drop. Thanks for your kindness in producing this material

[@CycloneCyd]

AWESOME. Thank you for sharing your struggle. Completing these jobs will boost your confidence and the next job, whatever that might be, won't feel so daunting. Keep up the good work

[@levelhead7857]

Thanks for this. My son has just been quoted £500 to do exactly what you’ve just shown. I’ll be able to do it myself with this tutorial.

[@johnnorris3442]

Great tutorial as I've just done my girlfriend's car. Though one thing guys, if you do go for the two new bolts at the catalyst end *GET THE SPRINGS AS WELL*, as the new bolts are 10mm shorter and will be a pigs arse to fit with the original springs.

[@MrWindermere123]

Excellent video of a job I need to do after a replacement back box lasted only 3 years before splitting at the bracket weld just before that rear box. The original lasted 12 years - some replacement parts are much lower in quality than the factory originals, I think.

[@liambaker7489]

I’ve got to do this on an aygo soon. Good video that gave me a heads up what I’m up against

[@ThorGunnarIversen]

You’re much cooler than Scotty Kilmer! 😎👌

[@CycloneCyd]

Thanks, Gunnar

[@franciscobloom4826]

Thanks a lot. The exhaust clamp idea worked great!

[@mikepedersen3626]

Just wanted to say, super video, just what I was looking for, thanks !

[@jimbo9310]

Nice one cyd , I got mine to change soon and this video is invaluable many thanks 👍👍👍👍👍👍😊

[@CycloneCyd]

This is the system I got. Good quality with Klarius fittings (get an M8x40 screw though) www.ebay.co.uk/itm/294918332616

[@underdogunchained]

Thanks for this Cyd. I would like to attempt this, but not confident where to place the axle stands to support my C1. I can't tell exactly where you've placed them. Could you consider making a video to show where to place them?

[@CycloneCyd]

You can do it! Lift the car using the front subframe and place the stands under the square section of chassis just inboard and behind the front wheels

[@Shaz-ho6bc]

Can i get ur advise what is the exhaust 02 senor called for bottom or theu both look the same from cat converter pegeout 107

[@joanjoandres705]

Nice video and nice Deep Purple s T shirt 👍

[@CycloneCyd]

It's the tour tee from their 2011 tour with a 30 piece orchestra (flippin' awesome gig. Thank you

[@SM-ot6up]

Do the spring bolts on the cat flange have nuts also that need removing or are they welded on. I cant seem to find any nuts on mine

[@andym6197]

I can’t get the joint on the cat to middle pipe to seal air tight it’s driving me mad, I’ve tried a new wire doughnut which was very loose onto the cat section but I’ve glued it on with exhaust paste, it seems to be were it sits in the cup ?

[@lpo718]

Very helpful video 👏

[@olitonottero7620]

super helpful thank you

[@Marktb363]

Very good video, thanks

[@dc1564]

Anyone know the name of the bolts that hold the exsausht to the cat? The one with springs, I'm tying to find them on ebay but can't find them

[@jcreswick]

Hi do you have a link for the full kit thanks great video

[@CycloneCyd]

This is the one I bought: www.ebay.co.uk/itm/294918332616

[@jazzyman99]

Wouldn't be easier to remove the O2 sensor when the exhaust is off the car?

[@overspeed3042]

Yep I reckon ur right, I shall be doing this on my little c1 tomorrow. Good tip sir thank you 👌🏻

[@jameswhitbread7173]

Use an O2 socket and breaker bar with an extension if needed

[@johnnyboyle4811]

Where would be a good site to order a new exhaust cheap.

[@CycloneCyd]

I got mine from an eBay seller - about 95 quid for the full kit delivered

[@johnnyboyle4811]

@@CycloneCyd nice

[@claudiopersico9570]

grazie

[@martinneumann7783]

I do have a brand new exhaust now but the next time I'm going to do this job by myself. Did you say 16,- or 60,- £ for the oxygen sensor? My mechanic told me a story of 200,- Euro if this device gets broken! In this video I learned a lot e.g. the word «chamfer». Wonderful. Thanks Cyd! 👍😀👍

[@CycloneCyd]

£16 - sixteen. thats for a universal 4 wire sensor which has no connector. For an OE sensor (complete with connector) I'd expect to pay £60-70.

[@martinneumann7783]

@@CycloneCyd Thanks for your quick response!

[@onlyme972]

Ebay plug and play £25 ish