CZDANG 933S SMART FLIP TYPE MULTIMETER.

czdang 933S
AC/DC 6-600V
FLIPCOVER*SMART MULTIMETER
TEST PEN BUILD IN TYPE
42CM PVC CABLE
SIZE 118X80X28MM
BATTERY AAAX1.5VX2PCS
DCV/ACB 6-600V
±0.5%+3
resistor 0.1 to 60M ohm
±0.8%+3/±1 .2%+3/±2.5%+3
capacitor 10nf to 60mF
±3.5%+20/±5%+3
diodeoutput 3V 1mA
continuity lessthan 50 ohm±20
maybe beep sound on.
frequency 10-10Mhz
±2%+3
eyesight record
it maybe have error
it any wrong
pls tell me for correct it.
BOARD 2023-08-15
CY-886 V1.0.1
R9 YEL,PUR,BLK,ORG,BRN
0.466M OHM
R6 GRN,BRN,BLK,YEL,BLU
R6A GRN,BRN,BLK,YEL,BLU
5 M OHMES
R9C 304
R9B 304
R9A 2612
U4 12X4 PIN
NO NAME
R13 R005
R18 000
R25 01D
R24 01D
Q4 Y1
R20 01C
R23 01D
R22 105
Y1 CRYSTAL 4.000
R21 01C
Q3 Y1
R10 01A
U7 8PIN
HE24C02
2228AB
R14 01C
U3 8PIN
FCX060
R12 01F
R11 01C
R10 01C
R7 01A
R5 35D
R4 01F
R3 01D
R2 01C
R1 01B
BZ1
MAIN IC
NO name
16x4 pin
Q2 Y1
Q2 Y1
SPEAKER
8 OHMES 2W
32mm
made in china.
1.fail in low resistor test
error 0.5 display 8
2. continuity low response
3.diode mode low voltage
and not to lit led
4.frequency max only 44khz
not 10mhz.
5.capacitor above 40mf
not 60mf.

[@bridges5659]

Lovely meter. It talks. ❤

[@wilsonluilui]

@@bridges5659 thx for watching.

[@bridges5659]

@@wilsonluilui Great. I was joking about Kung-fu. 😁

[@wilsonluilui]

@@bridges5659 thx for watching

[@wilsonluilui]

@@bridges5659 thx for watching

[@Gamersfanko]

I had a multimeter with a similar arrangement of probes (accta at-110); unfortunately, I had to repair the probes after 2 years of not very frequent use, since one probe broke at the junction of the wire due to constant bending when taken out.

[@wilsonluilui]

it may be buying a new testing probe change it,it may use again.

[@bridges5659]

@@Gamersfanko You should be able to purchase those leads easily. Most electronic shops keep them. It's not expensive , however you have different qualities of the leads. You can purchase online.

[@Gamersfanko]

@@bridges5659 They are attached to the board at this multimeter, so you need to soldering them.

[@bridges5659]

@@Gamersfanko Can you Solder them? Or maybe get someone else to Solder for you, a buddy who knows the electronics. Sorry, I'm from South Africa. Too far away or I would have done it in an instant for you.

[@bridges5659]

Uncle , teach me kung Fu.

[@wilsonluilui]

@@bridges5659 sorry we no any kung fu.

[@bridges5659]

@@wilsonluilui 😂🤣😂🤣