Whoever giving info is well experienced and covered all aspects
@gauravchaturvedi60803 жыл бұрын
1. Air compressor is used to remive dust and small interfering particles 2. Firstly, Prime coat is applied over its previous GSB layer (Granular Sub Base) to make good bonding among Aggregates used in GSB layer and so that they don't move when Base Layer is poured over them. 3. Then Tack Coat is used to make base layer ready for better adhesion with upcoming bitumen Surface layer (wearing surface), if needed, micro surface sheeting can also be used in areas of high annual Rainfall to prevent water going inside 🤗👌
@MS-qm2hj2 жыл бұрын
I think prime coat is applied over WBM or WMM layer not on GSB layer
@gauravchaturvedi60802 жыл бұрын
@@MS-qm2hj na bhai, prime Field pr GSB k upar hi apply krte h and existing surface par Tack coating for upcoming Overlay
@SanjayGupta-yw2jf6 ай бұрын
Prime coat is applied over WMM to stop the moisture of WMM into BM or DBM. And the Tack coat is used as a binder between BM/DBM and SDBC/Surface . And finally seal coat is sprayed over SDBC/ final surface as waterproofing
@SurendraKumar-ke9iu5 жыл бұрын
सर आप बहुत ही अच्छी तरह से समझते है आप अधिक से अधिक वीडिया बनाया करे । धन्यवाद सुरेन्द कासगंज
@tauseefrazakhan87623 жыл бұрын
Kasganj me kis jagah se hai.mai b kasganj se hu
@shalugautam91304 жыл бұрын
Good very nice video
@mebinglapung34054 жыл бұрын
Your explanation is crystal clear...very well explained...
@Agriculturebooksreview5 жыл бұрын
बहुत ही खूबसूरत से आप ने बताया सर् बहुत बहुत धन्यवाद आप से निवेदन है जो सरचना आप दिखाते हो उसे बिल्कुल नेदिक से दिखये ओर सभी टेक्निकल पॉइंट पर विशेष फोकस देते हुवे बताये धन्यवाद
@DEofficial885 жыл бұрын
Thanks
@hardikpatel84745 жыл бұрын
Sir basic ek theretical video banao Jo highway ki DPR se lekar final public ke lie open ho tab Tak ki processor...it will be help in any highway interview a lot
@vikrantsingh22044 жыл бұрын
Sir mujhe bahut achha lga aapka video dekh ke Sir mai btech kia hu Mujhe puri knowledge chahiye road ki starting se end tk ka Plz help me sir Aapki bht kripa hogi sir plz Meri vinti hai aapse
@Krsachinlearningpoint5 жыл бұрын
Bahut acchi jankari mili
@PhysicWorld98474 жыл бұрын
HELLO SIR , PLEASE MAKE A VIDEO ON THE TOPIC ARE :- (1) HOW TO SHIFT TBM . (2) HOW TO SHIFT FLY TBM . (3) HOW CHECK THE REQUIRED EXCAVATION LEVEL BY MAIN TBM OR ALSO ANY ONE FLY TBM VALUE . (4) HOW TO CHECK THE TOP AND BOTTOM LEVEL OF ANY EARTHCRUST LAYER BY MAIN TBM OR ALSO BY ANY ONE FLY TBM . (5) HOW TO CALCULATE THE QUANTITY OF EACH AND EVERY EARTHCRUST LAYER BY USING THE OGL DATA WE ARE TAKING FROM INITIAL STAGE OR BEFORE EXCAVATION STARTS. (6) HOW TO MAKE EXCEL SHEET FOR THESE ALL WORKS AND CALCULATE .
@rgrajesh81535 жыл бұрын
Bhayya I have a doubt 1) there is no safety for laying traffic vehicles are coming on laying surface 2) before laying it should be complete shoulders there is no shoulders preparation 3)in my observation there is no edge cutting happen in center 4) vehicles are not covered with tarpaulin so that temperature will reduce Awaiting for your reply Thank you
@K.Surendra-CE3 жыл бұрын
This video is very useful to all of us
@Rahulsahu-di6ye4 жыл бұрын
Sir pls aap road construction mai kite test hote hai iska detail video bana dijiye
@anindyapurohit19914 жыл бұрын
verry good road way industry work big network of india nice 😍😍
@thondupandrugtsang5 жыл бұрын
Excellent explanation. Really enjoyed the video. Jai Hind.
@DEofficial885 жыл бұрын
Thanks
@acecivil4 жыл бұрын
Very nice video.. Greetings from other Civil Engineering KZbin Channel..
@arunbhuyan78435 жыл бұрын
Sir ji thank you. Sir kitna square meter me kitna tone ya brass DBM lagega please explain kijiye sir please
@natvarsinhzala31223 жыл бұрын
Plz sir aese or knowledgable video banao plz🥰🥰👌👌👏👏👏
@sunilnegi59664 жыл бұрын
Very good bhai ji
@kianleena3 жыл бұрын
Keep up the best work👍👍
@mjsg84764 жыл бұрын
Trucks are doing their work fully.
@anilkumarvishwakarma5145 Жыл бұрын
Prime cot tack cote ka temperature laying time kitna hota hai
@sanjeevpandey43745 жыл бұрын
Good job Bhai video banae raho
@ranajitprasad20923 жыл бұрын
पहले लेयर के साथ जो vertical joints हो रहा है उसका edge कटिंग करना चाइए ya नही? यह फिर edge को blue lamp se गरम करना चाइए?
@gauranggshah71353 жыл бұрын
Good initiative
@souviksaha64085 жыл бұрын
Make construction video on super elevation. How to main gradient on super elevation portion
@harshrathod35804 жыл бұрын
Traverse jont aur longitudinal joint kese karte hai... samjavo
@shubhamshrivas88135 жыл бұрын
Sir paxe pe leval dena or check krne Ka video upload kre starting se TBS se Back side lete se or leval dete tak or chack krne tak
@ranjansharma27545 жыл бұрын
Marvellous video sir Sir ye kon se company ka work h or kaha ka work h jagah kon si h
@parveenjoshi61745 жыл бұрын
Very nice video
@mahajan..52995 жыл бұрын
Good video
@HarshitKS16185 жыл бұрын
Sir, is project ka Equipment schedule share kar sakte hain kya? Road construction main use hone wale equipments ka time cycle and resource allocation kaise karte hain.
@shubhamshukla15484 жыл бұрын
Thank you so much for this video..... Very knowledgeable
@MithleshKumar-xg3tx4 жыл бұрын
Thank u so much sir for such informative video ,pls aise video bare rahiye
@MithleshKumar-xg3tx4 жыл бұрын
Please aise videos banate rahiye sir. Aur road Ka technical term v bata dijiye
@altafpinjari83265 жыл бұрын
Dear sir, Sir GSB,WMM, DBM iski width kayse nikalate PL explain..
@e..41564 жыл бұрын
Sir road Geometrics and Highway alignment ke bare me bataye sir...........
@aspirantcivilengineers3 жыл бұрын
Road Geometry following terms are obtained. 1) Super elevation 2) Camber 3) Slope/ Gradient 4) width of carriageway 5) formation width 6) Sight Distance 7) Curve Radius
@mehmasingh88745 жыл бұрын
Thanks sir and please upload more videos like this
@rizwanmughal19124 жыл бұрын
Good information
@er.thakurmanohar25915 жыл бұрын
Bohot bohot badiya
@shubhamdahiphale5555 жыл бұрын
sir jo joint rahta h voh kaise karte h aur ek baat bituminous road ki aur detail mein vido kab banane wale ho
@ashishkatkade77824 жыл бұрын
1)What is exact difference between primer prime coat and tack coat ...?? 2) if Temperature is less then is possible that finishing may not achieved
@1414gp4 жыл бұрын
primer is a less viscous than tack coat. Primer fills the pores of granular surface whereas tackcoat is layed over prime coat or old bituminous surface to give bond between old bituminous/granular and new construction
@آرشآریا-ب3ت4 жыл бұрын
Primecoat is the first layer after basecourse which joint basecourse to firstlayer of asphalt and takcoat is joints to layer of asphalt.primecoat is low temprature than takcoat.and the perecentage of oil is less in takcoat
@devidasgaonkar25533 жыл бұрын
Road tayyar hone ke bad kitane din ke ander pani gire to Road kharab hota hai..?
@limayaden29955 жыл бұрын
Good simple commentary. Thanks.
@bilalz40913 жыл бұрын
DBm may kounsi metal use kartye hai sir plz bolo
@mr.perfectpraveen62434 жыл бұрын
Very knowlageble video sir , Thank you so much
@RakeshKumar-ss9qm2 жыл бұрын
Road work is quite difficult, compare to the building work.
Very good. But sir when mention different types of material also mention the related IS CODE. And also make a video on how to maintain slope in various layer.
@DEofficial885 жыл бұрын
Ok dear
@appasahebshelake56164 жыл бұрын
Very good vedio for knowlde. 1 How many ROLLING pass for BC and DBM.how calculate. 2.when become segregation how remove it..
@manohardhotre7184 Жыл бұрын
Sir, DBM matereal How mach one cub. M. How mach tone
@subratabrahmachari71405 жыл бұрын
Very good
@nareshchouhan65794 жыл бұрын
Dipp chek kese karte hai Sir Please btana
@ndtech81703 жыл бұрын
Thank you.. Informative video
@Abhinavkmr4 жыл бұрын
nice
@aurosrinivas Жыл бұрын
Good job
@DEofficial88 Жыл бұрын
Thanks
@civilengineeringexpert27915 жыл бұрын
Sir please upload a video for flexible pavement layers and how to level on that..
@Aurora_infra3 жыл бұрын
Road Marking Service
@eng.aminul392211 ай бұрын
Is it necessary to more thickness asphalt laying pavement? Like if our requirement 50 mm thickness asphalt after Compaction how much we have to put when we are laying pavement.
@DEofficial8811 ай бұрын
Good question 15-20% of thickness In trial streach we decide.
@amitbarisal73374 жыл бұрын
Bhai ak batch mix plant appol ANP 1500 ke bare mein Puri details ....ak video
@bmspahroo97393 жыл бұрын
U r awesome ...
@VijayKumar-mb5ik2 жыл бұрын
Praemcot ke upar taigcot spending ak sath y leayr by leayr hota hai
@AshishKumar-sj8mt5 жыл бұрын
Rod survey bataye kaise kare.
@shrikantchaudhari71344 жыл бұрын
Good evening sir survey ke bare me bataye ke wire par lavel kaise dete hai
@R.V.Singh112 жыл бұрын
Good 👍🏻
@MaheshYadav-qq7ln4 жыл бұрын
plz add a video on Construction of plain cement concrete pavement and RCC pavement with joints construction details
@yameensaifi9421 Жыл бұрын
Sir eta kese Hota hai
@kiranpandey76945 жыл бұрын
Asphalt mix Kaa ratio kya hota haii.. Bitumin dust sand and aggregate chips Kaa??
@manishcivil89795 жыл бұрын
Nyc Bhai
@er.thakurmanohar25915 жыл бұрын
Ble ble
@madangupta76112 жыл бұрын
DBM or BC karne se pahle machine me senser kaise set karenge sir
@noone-vn9kv5 жыл бұрын
Bhai vo DAS hai kya paver me jo baitha rahta hai paver technician
@ysh035 жыл бұрын
You are very helpful for us. Thank you sir
@ankitsingh-px6lt3 жыл бұрын
Sir 1 din mein kitna bm bicha sakte hain?
@vinayjhinkwan42334 жыл бұрын
TOO GOOD A VIDEO
@004hiren3 жыл бұрын
Sir I have a project where v have excavated 2 ft of black cotton soil and filled it with murrum then road rolled and compacted on that wbm 100 mm layer on that again wbm 75 mm layer now for the final wat you suggest shall I clean it perfectly apply tack coat lay 1 no mettle layer and then apply tackcoat and lay grit bituminous carpet on that
@tariqueequbal38114 жыл бұрын
Tack coat ke liye jo technical calculation ka details me btaye?
@user-zs7ym7ev6l Жыл бұрын
Sir Please give details of Rolling pattern & Joints
@DEofficial88 Жыл бұрын
Noted
@pankajrathore-zh5xe5 жыл бұрын
sir pag par level kese check karte h ki level ka yhi point dekhna h
@anirudhrana46655 жыл бұрын
Ek video sensor paver k baare mai bi bnao
@garvitdixit28795 жыл бұрын
Road ki density kistni hoti h. App is Road pr kistna load de rahe h
@civildna13734 жыл бұрын
Sir yh payg kyse dete hai , please sir mujhe janna bhut argent hai
@bikashgurung16654 жыл бұрын
Sir i need defenation to prime coat n tack coat
@joshibhuwan294 жыл бұрын
Is tack coat required between bituminous macadam and bituminous concrete or semi dense bituminous concrete
@DEofficial884 жыл бұрын
Yes ...if older than 1day If freshly laid within some hours then not required...
@joshibhuwan294 жыл бұрын
@@DEofficial88 is it written anywhere in irc or any other cide
@ShriSneh24124 жыл бұрын
White powder used after dbm work is what.. is it white cement of lime
@DEofficial884 жыл бұрын
No need of such lime
@rajeevkumarsam54995 жыл бұрын
Asphalt ka different test explain kijiye plz.
@erdheerajjadhav68954 жыл бұрын
Sir sensor paver me sensor ki arrangements detail me bata sakte hai ka i mean camaber and all arrangements plzzz...
@akhandpratapsingh56413 жыл бұрын
Sir aap se request h ki kisi bhi 4line ki vidio 1st level se lekar last level tak ka kyo ki es line me kam karna h plz help me sir
@maheshvasave27414 жыл бұрын
Road keyse bonate he aur road ke process ky he
@utpalbiswas62922 жыл бұрын
Nice...
@hiteshkapruwan96165 жыл бұрын
Sir as a fresher building construction m jyada scope h ya highway construction m ..plz reply ..boht confuse hun🙏
@DEofficial885 жыл бұрын
Definitely infrastructure
@hiteshkapruwan96165 жыл бұрын
Building construction?
@anirudhrana46655 жыл бұрын
Prime coat or tack coat ka kya difference hai
@kiranpadiyara3 жыл бұрын
Super
@welcomefarmer7625 жыл бұрын
Sir please ek video level ke upar bnayenge Kya level kyese krte hii
@rpsingh-ne7cf6 жыл бұрын
Sir please make one video on sensor , multiplex sensor and normal sensor..
@Aurora_infra3 жыл бұрын
Road Marking Service
@Rahulsahu-di6ye5 жыл бұрын
Sir pls rolling paas kitne dena chahiye ptr or tendam roller se
@shindesuraj50173 жыл бұрын
If one layer is layed at one side , then another side can be layed by using bed sensor , then why to use the string rods ( peg), at another side. Plz reply.
@pjvarasada3 жыл бұрын
Sar, please tel,how to fix design level of w.m.m. for sensor paver? String to be provided,on both sides?