⚡ DC-DC SEPIC Converter Design | Power Electronics - Calculations & MATLAB/Simulink Simulations

In this video, we will discuss a design of a DC-DC Single-Ended Primary-Inductor Converter (SEPIC). The operation of the SEPIC converter is similar to the Ćuk converter. The SEPIC converter can produce an output voltage that is either greater or less than the input voltage but with no polarity reversal.
Emphasizing an open-loop configuration, the converter will function in the continuous conduction mode (CCM). Using the specifications for the output voltage, output current, and output ripple voltage, we shall undertake the calculation of necessary component values. We follow a methodical step-by-step calculation process, followed by validation of our calculations through simulations in MATLAB/Simulink. #MATLAB #Simulink
🎯 Outline:
⏩ 00:00:00 Introduction
⏩ 00:00:28 Design Assignment
⏩ 00:01:13 Calculations
⏩ 00:09:45 Simulations in MATLAB/Simulink
👉 More Power Electronics: • Power Electronics
📚 Resources 👇
Power Electronics, Daniel W. Hart, ISBN: 9780073380674
🔗 Designing DC/DC converters based on SEPIC topology: www.ti.com/lit/an/slyt309/sly...
🔗 Designing A SEPIC Converter: www.ti.com/lit/an/snva168e/sn...
🔗 Benefits of a Coupled-Inductor SEPIC Converter: www.ti.com/lit/an/slyt411/sly...
🔗 High Frequency Power Converters: www.mouser.com/pdfDocs/inters...
🔗 High Frequency Resonant SEPIC Converter with Wide Input and Output Voltage Ranges: per.mit.edu/wp-content/upload...
🔗 TM SEPIC Converter in PFC Pre-Regulator: www.st.com/resource/en/applic...
⭐ If you have questions or comments, please let me know. Help us to reach more people. Like and share this video. Subscribe to our channel: kzbin.info?su...
⚡ CAN Education - Tutoring in Electrical Engineering, Analog Electronics, Power Electronics, Electric Circuits, Control Systems, and Math Courses
⭐ For questions, collaboration or consulting 👇
📧 [e-mail]
☎️ [phone]
🌐 www.canbijles.nl
Copyright © ir. Mehmet Can
No part of this video and text may be reprinted, reproduced, transmitted, or utilized in any form by any electronic, mechanical, or other means, now known or hereafter invented, including photocopying, microfilming, and recording, or in any information storage or retrieval system, without written permission from the owner.
#SEPIC #converter #design #powerelectronics #squarewave #power #electronics #analog #electriccircuits #rms #average #current #voltage #resistor #inductor #impedance #load #source #battery #analog #powerelectronics #electriccircuits #circuits #THD #totalharmonicdestortion #powermosfet #RLC #impedance

[@yosefpatinio3669]

Good videos! How do you make your circuit diagrams in the thumbnails? Do you have a video about that? Thanks.

[@CanBijles]

Thanks for your comments. Great to know that you liked the video. I use PowerPoint to make the presentations.

[@yosefpatinio3669]

Thanks for the answer, I ask about the circuit diagram itself, the icons for resistors , inductors,etc. Thanks ​@@CanBijles

[@CanBijles]

@@yosefpatinio3669 I also use Paint and make the drawings in PowerPoint.

[@biswajit681]

Could you please make same video on Cuk converter and its average model....if it great if you show current mode control with coupled inductor and uncoupled inductor

[@CanBijles]

Video about Ćuk converter is here: kzbin.info/www/bejne/anjNaISJnpyjbZI

[@biswajit681]

@@CanBijles Thanks for the response...do you have any plan to make cuk converter with closed loop control and could you please make a video on its working principle

[@CanBijles]

@@biswajit681 I plan to make the closed-loop control of a boost converter. Then, I will work on the control of other converter types if the time permits.

[@biswajit681]

@@CanBijles Many Thanks 🙏

[@CanBijles]

@@biswajit681 You are welcome 👍