I just followed your instructions exactly and it came out perfect. I'm relieved I haven't ruined £180 worth of worktop - thank you!
@MikeKeel Жыл бұрын
A good idea is to paint the inside of the cut worktop with an acrylic or oil based paint. If there is an ingress of water and the exposed inner worktop is not sealed, it could start to expand.
@capeofstormz5974 Жыл бұрын
It will definitely expand over time.
@sadikmeah40578 жыл бұрын
Great upload. I'm fitting my own kitchen today and this has really given me the confidence to have a go at putting the sink in. Thanks.
@shabanazehrakhan71164 жыл бұрын
Opopp
@chantelmorset717610 жыл бұрын
Great tip with the spade bit!
@fardellp6 жыл бұрын
It isn't done and dusted until you fix the clips in place - especially fun where you cut the base unit to fit the bowl. I have found that the clips supplied will need their own cut-out in the worktop (usuall 2-3mm) to enable the thickness of the clip to be accomodated. also on the thicker worktops longer screws may be needed for the clips. Its important to use EVERY clip position on the sink flange to ensure no leaks - I find that "pros" often leave out several clips if they are difficult to get at.
@99hank972 жыл бұрын
Ahah this is what I was looking for! I can’t figure these clips out 😂
@vrglcom Жыл бұрын
@@99hank97just silicone the sink fk the clips
@capeofstormz5974 Жыл бұрын
Exactly 💯
@chelseafeth3 жыл бұрын
Thanks for the upload and great tip on the spade bit 👍
@derekpartington21762 жыл бұрын
that's the most informative video I've seen on this subject
@johnmcdonald99779 ай бұрын
The best instruction video I have seen.
@MTAHMED442 жыл бұрын
Very good information Very easy to understand 👍
@rebeccarobertson18832 жыл бұрын
Watching videos on how to cut the hole out for my sink.. Great video thank you 😊
@Adrian-qr9mu19 күн бұрын
Another step would have been useful. Securing the sink to the worktop using clips and silicone sealant. Great no nonsense tutorial. Thanks
@KevinBower-gy5be4 жыл бұрын
A few more tips to add to an already comprehensive video - 1 Once the cutout's been done, fit the sink into the worktop via its clamping clips before you fix the worktops down, it's much easier than trying to do it lying on your back inside a cabinet. 2 - Same goes for the tap, overflow and waste plug/strainer - fit them in advance. Make sure your tap is nice and tight via the fixing nuts which are supplied, as these are often difficult to access for tightening if they become loose at some point in the future. Same goes for the flexi hoses for your hot and cold water. 3 - You'll sometimes find that when you've done the above and you put the sink back in its cutout, the sink clips catch on top of the cabinet, lifting the worktop slightly. If this happens, use a chisel just to take shallow notches out of the cabinet top until the worktop sits totally flat on the cabinet.
@petemc50704 ай бұрын
Very useful tips - thanks.
@desmondjrjohnston63154 жыл бұрын
easier-said-than-done love it
@harpandking2765 Жыл бұрын
Great job, well done!
@mtyrer64326 жыл бұрын
This is a very useful video. Step by step demo for my second kitchen but first re-using the sink which has no template available. Thank you Yves.
@scottnever87322 жыл бұрын
no mention that half the time the clips to tighten the sink down do not fall within the easy access area and extra routing is needed
@adamtierney4599 Жыл бұрын
Really helpful this mate thank you
@patrickjay64342 жыл бұрын
Lovely job, thanks for sharing 👍🏿
@vbroder158 ай бұрын
The best video@! Thank you.
@engineerau492 жыл бұрын
Very detail instructions
@ambroseharper83163 жыл бұрын
Great video, thanks
@DavidJohnson-dc8lu5 жыл бұрын
Sink manufacturers should just add the exact template one needs to cut out, all one should have to do is position template accurately and cut out around it!
@Chiefmucka3 жыл бұрын
Most sinks include them now
@jensschroder82145 ай бұрын
Usual dimensions are 50 to 60 millimeters (5-6 cm) from the front edge. Cut the hole 10 mm (1 cm) smaller all around.
@jonathanbriggs95037 жыл бұрын
sink clips lift the worktop off the unit? do i have to notch out for them as well so it sits flat again? and if so whats the best way to do this? thanks really good video
@user-jy2rs3nc6j Жыл бұрын
mulțumesc pentru videoclipul util
@darrenjowett80328 жыл бұрын
Nice job. Try drill the holes from the top and then as the point comes through the work top remove and gently drill upwards to prevent break out.
@tanvirislam247310 жыл бұрын
very complete video,thanks
@richardbullough72693 жыл бұрын
Got the basic stuff right , but forgot sealing the cut edges of the worktop cut out !!
@fardellp11 жыл бұрын
Well the problem with most "do it this way" videos is they show an ideal case and the "easy" bits! In the real world the sink has to be fitted when the worktops have been mitred and fixed in position- you can't do this after fitting your sink - and the sink seal and fixing clips aren't mentioned. The drill was on hammer action to drill the starting holes for the jigsaw - and you only need holes in two corners - think about it! Otherwise a good clear presentation - better than most!
@albertocowles7 жыл бұрын
why dint he make the sink cupboard 50mm so that he wouldnt need to cut it with a jig saw after cutting the worktop? Its time consuming
@paul-ne1bh6 жыл бұрын
can i just use my old worktop as a temlate
@DavidJohnson-dc8lu5 жыл бұрын
@@paul-ne1bh As long as your your new sink is the same size as the old one, SMART!
@internetpolification7 ай бұрын
How does the jigsaw blade avoid bashing into the wood frame underneath?
@brent070810 жыл бұрын
Great video. Well done.
@Brummiebutler4 жыл бұрын
Great vid... thanks💪
@1billwill7 жыл бұрын
THANK'S GREAT VIDEO.
@HARPzC4 жыл бұрын
Hi. Ready to cut out my new sink tomorrow? Would you recommend the standard sink clamps to fasten this to the work top or use silicone?
@DrNickBailey3 жыл бұрын
This is what I want to know - and also how to level it so that the water drains off the draining board and into the sink.
@vrglcom Жыл бұрын
Did you end up just using silicone instead and not bothering with clips? I used clips last time I fitted a sink and it was very awkward to do. I’m hoping to get away from using the clips next time.
@m.a.94715 жыл бұрын
Thanks
@sherwali58765 жыл бұрын
Nice very good
@merrynabird73205 жыл бұрын
Great video..
@liqing50462 жыл бұрын
Cute and accurate
@fana5927 жыл бұрын
very good, thank you
@ayazmahmood89707 жыл бұрын
very good job I like it
@DecoBlissTV7 жыл бұрын
Great, glad you found it useful : )
@dvdsmlprstylrАй бұрын
What about the lack of support at the front of the sink? Is that not a weak spot now youve cut into the support bar?
@thehudlessfarmer6 жыл бұрын
Thank you.
@T-P82 жыл бұрын
You don’t show how clips are going in. Especially onto that section where the cut out is basically flush with the unit’s back wall. I’d love to see how you do that
@ryanmaharaj43654 жыл бұрын
Do one with granite counter top
@marksmeaton1564 Жыл бұрын
A simple job, thts gonna take 4 hours. By the time youve sealed the worktop fastened down the sink, fitted taps and waste, and then plumb into existing hot/cold and waste pipes.
@SunnyHeirReborn311 жыл бұрын
nice one
@fardellp6 жыл бұрын
Why not lay out masking tape first slightly bigger than the sink outline, then mark everything (sink profile and cutting profile) on it?
@5610winston8 жыл бұрын
No fair! I never saw a reptile! When somebody promises a "skink" they should deliver! Seriously, I'm getting ready to make upgrades in my kitchen but I'm doing granite countertops.
@sultankhankhan31275 жыл бұрын
Good
@mensamoo3 жыл бұрын
Does anybody have problems with jigsaw blades wearing down when a worktop is cut from the underneath?
@mensamoo3 жыл бұрын
Carrying a worktop with a large hole in it could be problematic. Fitting and fixing the sink would make it stronger. Most cabinets for sinks do not have a top in them. Nice video.
@hallecamilleri97138 жыл бұрын
good job
@lazlokovacs54335 жыл бұрын
Back in my days we didn't have the luxuries of internet or KZbin, we had to use our brains, we had to have a high level of understanding by sight and the common sense to know what problems and dangers would be expected if the job wasn't carried out correctly unlike today 2019. 2012 is when you uploaded your video but you also gave advice on how to fuck-up on a inset sink fitting which explains why through the years so many second rate jobs and DIY jobs have caused so many problems and second rate workers. Your video is not how to fit a sink but how to do the cut out for the sink, the cut out and fitting a sink are 2 different facts also, your explanation and demonstration lacks details as to fitting a sink the most basic part of the job. My advice to people like you is understand details before giving advice to the people that don't know how to do these jobs, that fact alone is in the ending of your video when you set the sink into the cut out saying done and dusted, far from was it done and dusted, maybe in future you'll mention the sink seal and the clamping of the sink.
@wordimobi57654 жыл бұрын
Great so where's your video buddy? Oh your didn't make one, just came here to bitch about a guy that took time out to help others. Suggest put your energy into something positive.
@Easonwu3794 жыл бұрын
your the best, xd xd
@glockks563 жыл бұрын
Can I use a regular 4 inch grinder to make the cut?
@astrogerard20223 жыл бұрын
You dropped the sink in but what about the caulking and clips?
@rossbulawan45506 жыл бұрын
its not done yet caulk or silicon sealant should be used or water will get inside the cabinet
@olvsec Жыл бұрын
Maar waarom zaag jij die volledige spoelbak uit je kan gewoon een gat maken voor je bak en je zaagt te veel uit
@ottofumbler7267 Жыл бұрын
Well, you say that, but you've not actually installed it, as per the video title would suggest. What about undercounter seal and clips? Protection for the cut edges in the worktop and base unit? Preparation for taps and waste trap? Taps and waste fitting? You say it's easy, but that's probably because you've forgotten about all the additional work required to do a good job. Anything is "easy" if you ignore half the details. You could solve this very easily. Change the video title to "How to cut worktop for sinks and appliances".
@nthlevel8 жыл бұрын
Is that a festool i see
@anthonyfurtado96913 ай бұрын
👏👏👏👍
@michaelkennedy81353 жыл бұрын
Don’t move sink wile pencilling round it.
@Chariots848 жыл бұрын
He's obviously got a plunge saw yet still wants to cut the sink top out using a jigsaw 😁
@boc83858 жыл бұрын
lol exacly what i thought, lets just show everyone the old school way of bending there jig blade to over or undercut the top.
@TheGreg27104 жыл бұрын
Probably because most people use a jigsaw ya dick head
@Chariots844 жыл бұрын
@@TheGreg2710 😂😂😂 someones been triggered! 😂😂😂😂
@TheGreg27104 жыл бұрын
1984simongraham no, just most people do not have a plunge saw and the old scool way is fine. Plunge all you like pal. 💁🏼♂️
@placesweborn6463 жыл бұрын
@@TheGreg2710 serious question: what is a plunge saw? I'm used to the jigsaw as you mentioned it's old school and good for you 😁👍🏾
@catherinejackson65712 жыл бұрын
Sebastian ward how to work an insinkerator you tube
@hallusin7 жыл бұрын
but a kitchen sink to you is not a kitchen sink to me, ok friend
@oscarquispe224 жыл бұрын
15 mm of diference. genial.
@robmcghie52482 жыл бұрын
Those lines not them lines
@MountainRemodel7 жыл бұрын
Take a look at this kid who installs a counter top in a house - kzbin.info/www/bejne/kHmZpmeLZa2seZI
@peternolan56322 жыл бұрын
4 cm out
@wambamshookeran9759 Жыл бұрын
That's half done...
@MrDzserdzsely9 жыл бұрын
unnecessery work phases. just use a light color marker - so no masking taping only mark the cutting line - no duble marking
@colinmarmion10808 жыл бұрын
Greg
@missgreenieweenies12 жыл бұрын
Spelling errors make me giggle. Thank you
@mburns91969 жыл бұрын
he has used the masking tape to stop the jigsaw marking the worktop....imo
@philipbrown1383 Жыл бұрын
Should of named this junk....how to measure and cut a worktop.
@1989johno10 жыл бұрын
haha skink....
@laaazyk4 жыл бұрын
wait this aint twenty one pilots
@michaelgrant69205 жыл бұрын
WRONG!
@3333tas8 жыл бұрын
Handy tips for DIY, can do the same job in under 5min without all that jazz.
@arlingtonworksurfaces17407 жыл бұрын
Under 5 Mins, really?
@Louisjp18757 жыл бұрын
3333tas bullshit
@Phen0mable10 жыл бұрын
so he's doing this for ears with cheapest tools you can possibly get ?? Cheapest work top you can get and cheapest one bawl sink... Fuck me !!!
@foppo1009 жыл бұрын
Phen0mable Can't see your point does it matter what the cost is?
@Phen0mable9 жыл бұрын
foppo leeuwerke in this job is very important to have a GOOD quality tools. He claims to do it for long time but still have SHIT tools. It means that he lies or he's shit
@joshy36027 жыл бұрын
Phen0mable how are festool and bosch cheap?! Dont think you have a clue mate!!