Delonghi ECAM 22.110 / ECAM 21.117 Test Mode

Delonghi ECAM22.110 / ECAM21.117 Test Mode
For more information visit www.housenkitch...

[@ЮрийЖданов-о8н]

Excellent! После прогонки теста нашел способ устранения неисправности кофемолки (не запускался двигатель, загорались 2 значка переполнение и авария). В нормальном режиме сделал прогон-подогрев нажатием красной кнопки - неисправность устранилась.

[@23mmi]

can anyone tell me how can i reset if the infuser is locked on top position? I followed the steps explained for the realignment of the infuser but it seems that it does not work if it is blocked at the top position

[@johnnybb9866]

Thanks for the video. On the statistics mode-- counting the number of coffees. Is this number for single espressos? And assuming it is, when I make a coffee and press the 2 espresso button, does that count as 2 units in the statistics? My 10 year old machine has a huge number and there's not way it's correct unless it's counting a 2 espresso button (bottom left on the machine) as 2 units.

[@Nich_R81]

Hi! May I ask you something ? How can I adjust the grinding time? The dial front button is set on maximum but my coffe machine is grinding for 5 seconds. I have at work the same model and time is 7 seconds of grinding. Because of this, the quality of my coffe is inferior than other one. Thank you in advance.

[@colomboipl]

Do you have any news about the solution of this problem?

[@Nich_R81]

@@colomboipl No. I didn't find the solution. Maybe is a software issue.

[@xhobv02]

The grinding time depends on the size of the coffe. Is you manually set bigger size of the coffe (long press espresso button - start, after the amount is reached press again-stop). The bigger coffee for maximum volume grinds for almost 10s.

[@kittysitter2023]

Thank you! This was very helpful. There is NOTHING like this in the manual. Very strange...

[@wojciechspurek9764]

I have a question is it possible to reset the settings to factory defaults?

[@davidt.1433]

Same question for me.

[@Nich_R81]

same for me

[@nicevideos9828]

Same

[@vicer84]

Hello, may you help me? I have a delonghi super automatic 22.110. In the manual it's not clear what level of hard water should I program the machine. If the water I use for the machine is not hard. I mean is really good and pure water should I program the the coffe machine in level 1 or 4? It's not clear if the soft water is level 1 or 4 And the hard water is level 1 or 4. Tanks a lot

[@texplorer1]

When attempting to remove the infuser is stuck in an incorrect position 1. Close the service door and replace the water tank 2. UnPlug the appliance at the mains and switch off at the back switch 3. Switch the appliance on 4. Switch off, and wait for this process to complete as indicated by the lights going off The appliance on and allow the infuser to automatically realign correctly. The infuser is now in its correct position and can now be removed.

[@yavkatakamenov]

I have a problem, sometimes when I start my machine it crashes. I have ECO and exclamation mark triangle ? When i restart from back button it's same ?? After a long period of time with the machine turned off, does it work everywhere?

[@rejuvarhuddlan4171]

I did this and now I can’t get the machine to switch back on again 😬

[@ricolimorico3386]

Hi, Thanks a lot for all your vid I bought my DeLonghi Magnifica XS from Costco MN 120 v - 60 HZ 1250 W Type ECAM 22110 B P= 1.5 MPa (15 bar) When I took it to North Africa and by mistake I plugged it in 220 V I smelled little burning. I still can turn it on I can hear the coffee grinding all screen look good with green and yellow light but it doesn't dispense water nor a coffee. Please help.

[@alipasa9631]

Bizdede ayni makina var önceden pres olarak çopu veriyordu birtane yayi dustu simdi pres yapmiyo ve servisi yok Yalovada tavsiye edermisiniz serviz

[@brianstockford]

I need some help and hope you can point me in the right direction. As soon as the machine goes to put power to the pump it comes with the three error lights. The two on the outside our blinking and the one in the middle is solid. Thoughts.

[@floydfenger6677]

I have the same problem it won’t even do 1 function

[@mortiblue]

@@floydfenger6677 did You fix it?

[@mortiblue]

Did You fix it?

[@GabrielaVielman-o9s]

What can I do if the warning light turns on, but the light is never off, can you help me, please?

[@abcdefg8241]

Hi, can you add a video on how to open the back cover of this machine?

[@stevenchin985]

Hey, do you know how to set the ml. Don't know what happened but I now get 2 shot of espresso for single short function so coffee is watery. Thanks.

[@Naughtystimpy]

Is there a way to reset the stats counter on delonghi coffee machines?

[@DjTronk]

How can i exit this mode?

[@technomad900]

This is really helpful , is this available in written form ?

[@technomad900]

Its ok , I found translate.google.com/translate?depth=1&hl=en&prev=search&rurl=translate.google.co.uk&sl=de&u=www.kaffee-welt.net/index.php/Thread/1087-DeLonghi-Reparatur-und-Wartung-Sammelthread-zur-ersten-Hilfe/%3Fs%3Df2e07e7fb1488382bea0fb66d6538b502ce00a2f

[@bradward3012]

Helllpp! My wires seen to be loose and I cannot turn on my coffee machine as the on /off button isn't responding

[@GoldwingriderDCT]

I have the same problem, do you have a solution allready?

[@victorbotezatu729]

cum se reglează cantitatea de cafea???

[@sazsazsaz2012]

What is the purpose of this testing mode? Thanks.

[@ihenrynl]

to test the grinder and pumps and to repair the infuser when it is stuck in an incorrect position.

[@uldericodelgiudice7532]

Fatto la decalcificazione alla macchina caffe de longhi ma non si spegne più la Lucina rossa decalcificazione o rispettato la normale procedure a fine ciclo mi lampeggia che significa devo aspettare che si riscalda

[@casabryan_5]

after doing the test I am left with only the flashing orange steam led without being able to do anything, I turn off the machine and turn it back on with the same problem

[@brmba]

Hi, did you found the solution? I have the same issue

[@simoncdm4448]

Hello do you find a solution?

[@miy7232]

Had same issue , after trying to reset to the factory settings . Can’t remember exact order of pressing but I briefly put steamer to I position , returned it back to 0. Then pressed top left corner switch off button . Then switched off in the back . I didn’t unplug it from the mains . It worked

[@marcd710]

Your machine is in initial delivery mode after exiting the test mode. Fill the water tank, put a cup under the hot water tap and turn the hot water knob to the left. Machine should start pumping water and end after a short while, then it should return to normal operation.

[@miy7232]

Actually , I kept holding steamer button while turning off n on I/O hit water wand lever briefly. Then switch off thermometer butin n released the steam button

[@garyaussie3778]

Hi, anyone know how to factory reset this model? Is it possible?

[@truthisinthebible]

Hi Gary, did you ever found this out? We're also looking to reset the machine...... :-)

[@desmeis4282]

help please, after tests, the Delonghi stay in test mode even if I turned off and when I turn on the machine not start (all lights off)

[@HKDIY]

Hi, did you unplugged it from electricity? Usually you need to unplug it and it helps.

[@desmeis4282]

@@HKDIY Hi, Tanks for your Answer. It's done with no effect Regard

[@بشرىعبدالله-ه4ف]

How can I warm up the device?

[@Star4live]

just got one, turned it on and right at the start the outside buttons are ligting up. you have any idea what i should do next?

[@HKDIY]

Hi. Have you made "using the appliance for the first time" procedure? English manual page 10. First time is a little different because water have to fill system & etc...

[@Star4live]

+House&Kitchen when I get home from work I'll try it again and let you know what happens, the so far :)

[@antigonezeqiraj1522]

Helen Winters

[@whoneedsroads]

And the remaining question is: how to EXIT the test mode?

[@HKDIY]

Just turn off main switch on the back panel or unplug the machine

[@whoneedsroads]

House&Kitchen nope... tried that and it didn't work for me. Tried different keys and switching on in the end. Somehow it finally exited. No clue what key combination did it though.

[@dodomat]

May I know how to exit the test mode? Thanks!

[@dodomat]

House&Kitchen this does not work. Help!!

[@trendmend]

Did you ever find a solution?

[@bobanvuksanovic5466]

This literally f**ed my machine.Won’t event start up after this

[@trendmend]

Hey, did you find a solution?

[@Mohammed-ry9nq]

same here, any suggestions ?

[@brmba]

Did you manage to fix an issue?

[@brave1671]

Thanks a lot!

[@judgexxl]

Tranks, very helpful

[@kucukevaletleriatolyem7641]

Selam dostum mükemmel anlatıyorsun

[@lolirot]

hellow, how you make an a factory reset on this machine?

[@HKDIY]

Hi. Machine plugged in but OFF (main switch on 0), press and hold the buttons "ON" & "Short coffee" (left side upper and middle). Release the buttons after the LEDs Coffee are blinking. To complete the procedure, switch the machine ON and then perform a "washing/warming" cycle, then switch it OFF with the main switch.

[@lolirot]

thanks alot also my machine dosnt want to "turn on" i mean doesnt heat the water what kind of problem is, if i let it along time "ON" just appear a little triangle red and doesnt do anything more else @@HKDIY

[@martvandenthillart9140]

A hint for the reset: it misses one key step, as described it does not work. Correct steps for the reset are: Machine plugged in but OFF (main switch on 0), press and hold the buttons "ON" & "Short coffee" (left side upper and middle) and flip the mains switch (on the back) to 1 (ON). Release the 2 (front) buttons after the 2 LEDs for Coffee are blinking. To complete the procedure, switch the machine ON (with the front switch) and then wait for it to perform the normal "washing/warming" cycle, then switch it OFF with the main switch (on the back). Wait 10 seconds and switch the mains switch on the back to 1 (ON). All LED's light up short. Switch the machine back on with the front button. Now it is factory reset. This solved my problem of a very short grinding time. This short grinding time had occurred suddenly, after ca 3 years of use. No matter in what position I put the dial for amount of coffee on the front, it was always ca 2 seconds grinding. Resulted in very weak coffee. Normally between 8-12 seconds, (depending on how much coffee you want for the brew). The short grinding time only occurred with the small espresso button. The double espresso still had the correct grinding time. This inconsistency lead me to believe it was a software or settings problem, not a hardware/board problem. And proven correct. Thanks for the poster above, the described reset did its job. (PS I tried other reset, cleaning, powercycle or unplug but they had no result) @@HKDIY

[@coreelec3953]

@@martvandenthillart9140 delongi can resset only in test mode

[@miciz]

@@martvandenthillart9140 Hello, I have an ECAM 22.320 and I can't reset the PCB machine. I perform the following steps: - With the machine connected but turned off (rear switch on 0), I press and hold the "ON" and "Short coffee" buttons and turn on the rear switch. - The words "QUOTA RESET" appears on the display At this point I can not do anything, if I press any button nothing happens. I can't press the power button to complete the procedure, nor any other keys. Please, can you help me?

[@chiwandos9938]

Ничего не понимаю

[@kostyanika2007]

Вот полностью согласен. Мне бы про последний тест хотелось бы узнать

[@Visage3]

How to exit this test mode

[@trendmend]

Did you find a solution?

[@Visage3]

@@trendmend Yes i've found it. Simply turn the steam lever to its initial position and its ready to go.

[@uldericodelgiudice7532]

Sarà che nella prima decalcificazione o messo 50ml e la macchina non a fatto bene la decalcificazione

[@alaciobanu9048]

Mă ajutați vă rog și pe mine?

[@alaciobanu9048]

Sunt aprinse toate butoanele și nu găsesc motivul

[@1974christo]

this is not a movie for idiots or for fun XD

[@DjTronk]

How can i exit this mode?

[@sabirzahrani6387]

What is the purpose of this testing mode? Thanks.

[@ihenrynl]

to test the grinder and pumps and to repair the infuser when it is stuck in an incorrect position.

[@DjTronk]

How can i exit this mode?

[@DjTronk]

How can i exit this mode?

[@DjTronk]

How can i exit this mode?

[@DjTronk]

How can i exit this mode?

[@DjTronk]

How can i exit this mode?

[@DjTronk]

How can i exit this mode?

[@DjTronk]

How can i exit this mode?

[@trendmend]

Did you find a solution?