Delta Auto Calibration using LCD controller(without gcode)

[@macsogandares8383]

Thank you, I've tried everything (including firmware) and this was the last step to getting everything to work.

[@RussTaylor83]

Thank you very much for the video and the firmware, both are fantastic and have made my Linear Plus much much better :)

[@milesmoody56]

This is an excellent video. Thank you for making it and thank you for the firmware you uploaded

[@spamy6661]

You and your video is amazing. Thank you so much!!!

[@lukasschworer840]

Great Work youve done there thumbs up and Thank you

[@curtisbarclay2292]

Does Google have a voice translator? Thank you all the time you have spend on this project and to share this with everyone else. That's cool!

[@gridarmorfix]

Curtis Barclay use captions.

[@GruneGames]

Nice pimped out machine. Could you show what you did about the endstops ? My Kossel worries me, ramming hard into the tower endstop with each time auto home.

[@jpauto-hanhat399]

please help me ! when I check axis. the center is always perfect. then it acts like a rainbow from side to side of x and y. Autotune fails. Manual tune fails. Never saves the settings! I always hit store and they show but it's like it ignores them.

[@phuongphanminh72]

THANK YOU

[@TheMrCaveman]

Thanks for this explanation!!! What is the module you have between the bed level sensor?

[@michaelvogt2555]

hi there. I sadly fail on Z offset calibration. Using Kossel Linear Plus with your firmware. Using V2 sensor for probing. Inverted in firmware to fit hardware the z-probe as mentioned. I am using the standard heatbed with standard cover so far. When I try to do #6 z offset calibration ... I move Z down to a value=-008.0 or -008.1 till paper slide n scratch. when I want to do next step and set the z-offset I can not go that far for values. as -14.9 given + (-8) will be about 22.9 or 23 I can not get the value that big, Turning the wheelknob maximum value is -20.00 So I can not enter -22 as a value to fit the calibration :( HELP .. what to do, where do I modify it?

[@OlehPiranit]

hi bro, same issue, did you find solution?

[@OlehPiranit]

I found a solution in Configuration.h if you use v2 sensor Z_PROBE_OFFSET_FROM_EXTRUDER must be -14.9 #define Z_PROBE_OFFSET_FROM_EXTRUDER -14.90// for v2 sensor = -14.90 for presure sensor = -0.07 // Z offset: -below +above [the nozzle]

[@comkver]

Could you please show how to upload the firmware?

[@andreyal]

hi! Thank you so much for firmware! Question...After calibrating delta, i checked Z offset with paper, and it shows 0.000 (i use v2 sensor). But there is two 0.000 points (i heard a sound of step motor)...upper and lower. And it seems that saves an upper value, the hotend a little bit higher. So how to save a lower 0.000 ?Thank you

[@billleonard2015]

How did you make the printer so quiet? I can hear the controller dial click, I can hear paper rustling during calibration. I can even hear the endstop switches clicking but I can't hear the motors. Well done. What's the secret?

[@reinholdu9909]

Stepper driver TMC 2130 (or TMC 2100) ...look at his blog.naver.com/godnanai/221264208839

[@vulcorgrou7437]

Thank you very much!

[@cnc1]

안녕하세요. 좋은정보 감사합니다. 그런데 7:36초에 311.43- (-1.65) 라고 하셨는데 플러스 아닌가요? 헷갈려서요

[@namsugak8690]

영상을 다 보셨는지요? 마이너스 해서 정상인데, 플러스 해준다면 옵셋이 플러스이냐 마이너스이냐에 따라서 노즐이 베드에서 떨어진채로 움직이거나 반대로 더 깊이 들어가려 하거나 둘중 하나의 상황이 발생하겠죠. 직접 실행해서 확인해보시기 바랍니다.

[@ВладиславЖелезкин-п6к]

what do you think about tmc2208? Can they be used? One hundred change in firmware? what is better to buy? 2100 or 2130? omissions printing is?

[@OlehPiranit]

better 2130 v1.3 with spi

[@NMHC1978]

how many itterations does the auto delta calibration do ?

[@michaelvogt2555]

me it was 5-9 depending on firmware. IMHO its ok as each iteration probes other areas.

[@alexpegrande]

10

[@lichbilly]

펌웨어가 동일한 flsun delta 에서도 동일한 과정으로 진행하면 되나요?

[@namsugak8690]

flsun delta는 펌웨어가 동일하지 않으며, 사용하는 센서도 다릅니다. 과정은 유사하게 진행하면 되겠지만, 원활히 진행된다는 보장을 드릴수는 없습니다.

[@YaqoubM]

can i get firmware link pls ?

[@namsugak8690]

I already included the firmware link in the description