Derbi MHR Team 80cc Project [#1]

Trailer SRT : • Trailer | SRT
Malossi MHR Team 80cc Project [#2] : • Derbi MHR Team 80cc Pr...
Facebook : / savageracingteam
↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓
Set up :
Cylinder: 80cc Malossi MHR TEAM
Cranckshaft: Malossi RHQ
Exhaust: MK PRO RACE 3 Limited Edition
Reedvalve: Malossi VL6
Clutch: MOST Racing
Ignition: -----------
Carburetor: YSN 30mm PWK
2x Radiator
Engine blocks: Derbi €3
Sparkplug: NGK B10ES + NGK B-E105
------------------------------------------------------------------------------------------
Music : Klaas - Night To Remember
• Klaas - Night To Remem...

[@SandelsG]

Very good video!

[@davyd7991]

Hey man what did you adjust at 4:11 when it started to rev being on the stand tilted? I have the same problem. When it's tilted on the stand the revs go up and when I standit up straight it returns to normal reving. Any ideas?

[@xx_g3t_rekt__xx603]

Doviduolis he adjusted the idle screw but in your case you probably have a to short throttle cable

[@davyd7991]

@@xx_g3t_rekt__xx603 ur probobly right but when it's tilted at first it lowers the revs looks like it's about to turn the egine off but then the revs start to increase and keep increasing until I manualy shut the egine down or stand it up straight

[@garethoflaherty941]

hi dju know the vid of the 125 cc go kart were did u get the rear tyres n how much

[@srt8830]

Hey! The wheels was already mounted when we buy the go-kart. I do not know how much they cost but the tyres brand is ELIMINATOR (Slick). The model of the go-kart is of the year ~1970 (Old Go-Kart of the French Championship), so it's still going to be hard to find tires of this brand..

[@rosh3918]

same setup i only have 21 mm carb should i upgrade ?

[@nikopalomaa9889]

Yes you will get much more torque i have stage6 77cc and enox so its a piece of shit exhaust but when i upgraded from 21 to 28mm carb it was night and day difference

[@jasoncoste6660]

allumage d'origine a quoi sa sert ?

[@Benis333]

Hi guys! idk what's wrong with my bike... (derbi) I have stage6 80cc, 28mm dellorto, mvt ignition and yasuni R3. The engine doesn't start without choke and when you put it of it doesn't iddle and shoots flames from the exhaust. i have tried 120-140 jets and checked for airflow but intakemanifold is not broken and cylinder top doesn't leak air. I tried also to change ignition timing but it didn't help at all. Engine works very similar with 120jet as 140jet so i don't know is there anything to do anymore. I would be really happy if you could help me out in this one!

[@srt8830]

Hey, can you send me a video (gives gas in the video). If you can ride with it can you describe the reaction of the engine (tr/min, etc...)

[@Benis333]

i can send you a video but i try to explain it first.:D So i start the engine (with choke because it doesn't start up without it) it works fine in idle and when i gas it might boooo if i turn the gas too fast and with full gas it shoots flames from the exhaust. Then i put the choke of and it doesn't run anymore without gas and still shoots flames and does boo with too quick gas. I can't ride it atm because there is snow and i have only smotos :D. hope you understand what's happening because i don't

[@ejtisevn]

Badly settled ignition!

[@marjamix]

Benis :-D reippaasti isompaa suutinta tai sitte se vuottanee ilimaa jostai

[@marjamix]

@What the Shrek ei ryypyn pitäs vaikuttaa jos pelkkä ajotus pielessä

[@Fiat_176]

Why not 94cc?

[@madmarkkis]

mhr for life (iha paska)

[@joonatuominen8273]

Juurikin näin vittu

[@vkxz666]

Janne Nurmi stage 6 tai italkit

[@vkxz666]

terpi mopoo yök

[@desyncgang5184]

@@teho-ostatso228 mxs tehokkain;)

[@rapaperse9148]

Desync Gang 2fast :)

[@annastodberg640]

Does Malossi mhr 80 fot tight on the original motorblock(?) of does it need bygger space to make it fit?

[@srt8830]

Yes. You are not forced but it would be better.

[@johnnanon5812]

Anna Stödberg nop

[@sigurdberiksson5584]

what main jet do u have?

[@srt8830]

120

[@20000milka]

And final result? Top speed?

[@srt8830]

I do not know yet.. I think between 160 and 180 km/h 25-30hp

[@basjopfluit765]

SavageRacingTeam hahahhahaha

[@srt8830]

Bas Jop Fluit It was not supposed to be funny :)

[@basjopfluit765]

the world record is little over 160 km/h

[@basjopfluit765]

and you think you can break that with a mhr 😂😂

[@fatalghost1726]

hi man nice bike but can you please tell me how much the total project cost?

[@srt8830]

Hey thx! mb 700€ (just the pieces) Most parts are new but buy at a small price

[@fatalghost1726]

SavageRacingTeam 700 for the hole motor build wow..do you know abou how much hp it is or the top speed ?

[@jonnenaamupala7857]

Alex Gram About 19hp

[@MrGroundpounderz]

Bro if that is the original cranksharft i would get that out of there real quick. Beacouse the big end bearings wont hold up for long

[@srt8830]

This is not the original crankshaft. I have a Malossi "RHQ" crankshaft.

[@MrGroundpounderz]

SavageRacingTeam ahh it looked like the original sorry my fault ✌🏻️. Very nice setup though 👌🏻

[@srt8830]

No problem ! Thanks bro :)

[@letiziacolamussi64]

How much this??

[@larskissing]

when you dont have enough money to buy an new exhaust :-

[@milan5159]

😂😂 thrust me this wasn't cheap

[@getawaycrew5368]

@@milan5159 he should have bought the mhr supermoto exhaust

[@milan5159]

@@getawaycrew5368 well every one has their own preference

[@getawaycrew5368]

@Milan yep but the mhr supermoto is made for the mhr team cylinder so it is the Best exhaust for the cylinder. Mine had 24hp from rear wheel. It was heavily modified and it never broke because of so strong crankcase.

[@srt8830]

​@@getawaycrew5368 The final video arrives soon (after 3y haha) : new exhaust, ignition, etc.. and some tests

[@adarshkeswani2319]

Hey guys! Is this engine for sale ?

[@pvsukisuki9085]

Yes