Devilbiss gti pro spray gun review and air caps Te10 Te20

[@lewigas290]

Best description of a drop cost anywhere on KZbin. Well done and thank you 👍

[@dredfxcustompaint]

Thank you 👍

[@eapauto]

You make it look easy sir! You do excellent work. I just found your channel and just subscribed!

[@dredfxcustompaint]

Thank you so much for watching and supporting the channel

[@jc2200]

Love the video and the run through on the video..great explanation..great advice from Arthur Mate. Great review on the video review..great video mate I like this brother..💯👍

[@dredfxcustompaint]

Thank you Mr c glad you liked it 👍

[@AliVapeReviews]

with my pro lite TE20 for clear i run only 26psi maybe i need to try 30psi but says 26psi max on the air cap

[@ANDY-we7mr]

THANKS ROB FOR SHARING THAT AND PUTTING THE SETTINGS ON ROB I HAVE A DEVILBISS GTI PRO RED ONE WITH THE TRANS TECH CAP HAVE YOU USED ONE BEFORE

[@dredfxcustompaint]

No not tried that one

[@ANDY-we7mr]

@@dredfxcustompaint Rob i spray a bumper came out ok but with a dry effect what causes that not close enough

[@dredfxcustompaint]

@@ANDY-we7mr try slowing down a bit or up the fluid on the gun

[@JohnWD40TC02]

Hey Rob thanks for taking the time to do the split screen again mate as I know it takes twice the amount of time to edit👌 as was mentioned below the description on the drop coat was really well done and well explained, I've seen some do the drop coat while the paint is still wet and some do it after it's flashed of so is there a right or wrong way to do it? Before I got my DV1 I used my GTI Pro and TE10 but I used the 1.2, I'll have to dig it out again🙏👍

[@Cupra317hp]

Always fun to Watch a pro

[@dredfxcustompaint]

@@Cupra317hp 👍

[@Cupra317hp]

@@dredfxcustompaint Greetz from germany :)

[@deanbrown7643]

Good advice on them caps bro where did you get that gem of advice from ??? 🤣🤣🤣🤣🤣

[@dredfxcustompaint]

Hello mate the te20 is a cracker mate 👍 thank you 😊

[@deanbrown7643]

@@dredfxcustompaint knew you'd love the finish it achieves it absolutely destroys clear 👏👏👏👏

[@davidvrrampaul8663]

Love the video and explanations. I only got my pro lite today and love its versatility for bas and clear. Btw What nozzle size did you use for clear was it 1.4 or 1.3 with te20 cap. Thanks and keep the videos coming.

[@deanbrown7643]

@@davidvrrampaul8663 you can use either bud just adjust to suite 😉😉😉😉

[@tedc9306]

Why did you choose to use the T20 cat with a 1.3 could you have used a 1.4 with the T20 cap for Clear what was your thoughts behind either or

[@dredfxcustompaint]

Hi yes you can use a 1.4 mm but that's what my gun had in it at the time so went with it 👍

[@B15SDMDESIGNS]

Can you use the TE20 air cap for solvent metallic basecoat aswell? I have a TE20 air cap but dont really want to buy another air cap as I rarely spray anymore

[@dredfxcustompaint]

Yes you can use it for base and clear coating

[@deanbrown7643]

Te 20 on the clear coat all day long glad you've shown viewers how good that cap is 👏👏👏

[@ForwardMovingDesigns]

Perfection brother.

[@raelynn2399]

I have nibs in my clear, even if I don't spray and I pour it onto a test panel....any ideas what it could be?

[@dredfxcustompaint]

Hi its all about cleaning your work space down first before you start spraying give the floor a wet down with water that will keep some dust down aswell Then when it comes to your panels blow off and tack rag down between each coat of paint that helps out loads

[@bensonporter1384]

Should I buy the te10 for basecoat & te20 for clearcoat or just buy one cap for everything?????

[@dredfxcustompaint]

Hi I find the te10 really good for base that's what we use all the time in the bodyshop then when it comes to the clear coat the t110 will give you a flatter finish But you can also use the te20 for clear coat it will still give you great results 👍 if you can afford another cap I would say yes go for it 😉

[@kingartsprojects4150]

Hello, I purchased a Devilbiss spray gun model - GPG- 7E7 with a HE-7E7 CAP, and it came with a 1.2 and 1.3 tips. Are you familiar with this gun, and should I use it for base or clear? Thank you, and thanks for the great information provided in your videos.

[@dredfxcustompaint]

If it came with a 1,2mm and 1.3mm you will be good for base and clear coat

[@jeremyking5684]

About how far away from panel do you hold the gti pro lite?

[@dredfxcustompaint]

Hi Jeremy about 9inchs away from the panel that's a 1.4mm set up 2bar pressure

[@deenunya7735]

What cost is the Gun and Caps Approx?

[@dredfxcustompaint]

Hi Dee if you check out the link in the description you will see the cost on the guns and parts 😉

[@diamonddetails9445]

💯👍👍👍

[@diamonddetails9445]

Dear Sir, would you PLEASE make more ANI content? We would be grateful 👍💯