Devongunsmith Diaries #9 Browning B25 A1 misfire faults

Devongunsmith Diaries #9 Browning B25 A1
lost footage of a lockdown shotgun repair of the classic FN Browning B25 A, my client brought his old favorite gun to me with misfire and possible cocking issues, Epic fail, No one was manufacturing any mainsprings.
The Devongunsmith Diaries concept was conceived by me during lock down, and the premise was to be able to perform work without a fully set up gunsmiths workshop, but rather, using just the Cottage Kitchen Table, a few hand tools, some cordless tools, a table vice, and other small DIY tools.
While the channel is not specifically intended to be a how to guide, it is mainly for entertainment.
While in the UK gunsmithing must be performed by the Licenced Gun Trade, KZbin is without borders, and if the channel is useful to someone as either entertainment, or indeed helps you to decide if a repair might be possible, then I have been a help to you.
As an Amazon Associate, I earn a small commission from qualifying purchases, this helps to support the Devongunsmith Channel, The following are products I use regularly.
The Moly Grease I use is this one: amzn.to/46pJ4sP
Bisley do a smaller pack of Moly: amzn.to/45xNZqe
The lithium grease I also use: amzn.to/3tmh4rh
Light gun oil in a small pack: amzn.to/3LYRKOD
The Pipe Pliers use to make my custom coil spring pliers: amzn.to/46DzHFE
The Grace USA gunsmith turnscrews I use are these: amzn.to/45nIx9q
The Generic version of Mirlon or Scotchbrite I use: amzn.to/46rCGRT
Wheeler trigger scales I use: amzn.to/3S2sWJz
My 6mm stock bolt T bar for Beretta: amzn.to/3tuHkQt
Solvent Contact Cleaner, to use to clean the metal parts: amzn.to/3ZQW0FG
Browning Legia Gun Oil Spray: amzn.to/46qSUuB
Cold Blue Gel G96 which I use for touch ups: amzn.to/46PoykX
Cold Blue liquid smaller Bottle, which I use for complete bluing: amzn.to/3rLF4nt
Adjustable Hand Reamer Set 17-19mm and 19-21mm: amzn.to/3M1U4o1
Cutting & Tapping Oil Fluid:amzn.to/3FeMzWX
Dial Bore Gauge 18-35mm: amzn.to/3M18LHR
12g brass snap caps: amzn.to/46sVP5X
Stock Bolt Long Pattern Screwdriver: amzn.to/3PTFL6e
#browning 12bore #shotgun #repairs #gunsmith #gunsmithing

[@piaggio780]

I am sure enjoying watching all of your videos… I am a sporting clay enthusiast for the last eight years here in the USA, I should both competitive and just club level, and I have learned a tremendous amount about my O/U Shotguns! Thank you! Michael P.

[@JohnnyCANAAN]

I would like to thank you very much for all the videos that you post that makes us understand better our hunting rifles and shotguns and how to fix them and maintain them. Keep up the good job mate.

[@devongunsmith4698]

Thank you

[@perrypappous1550]

Well done. Love the extras! Perry P., So Cal, USA

[@paulsherrod1365]

Just popped in on you again ,very entertaining . Quite talented but not overly serious. Thank you.

[@devongunsmith4698]

Glad you enjoyed it!

[@noelkiernan482]

I REALLY ENJOY WATCHING YOU AT WORK, I APPRECIATE IT IS DIFFICULT TO DEMONSTRATE WHILE KEEPING WITHIN CAMERA. THE MODERN ONES ARE STREAMLINED, I HAVE A B25 AND A B525. THE B25 IS LIKE DRIVING A CLASSIC CAR TO ME. I WILL NOT BE TINKERING WITH EITHER, BEST LEFT TO THE EXPERTS. THANKS AGAIN FOR YOUR PATIENCE ,

[@paulsherrod1365]

I would like to see a video doing what you just did with a charles daly Miroku . Flat spring maintenance and a brain picking cession

[@devongunsmith4698]

Do You have one that needs repair or servicing?

[@paulsherrod1365]

@@devongunsmith4698 no ,I own two but they are in good working order . I would like to see it done to store in my memory banks. About the servicing perhaps. I’m a retired machinist and heat treater pretty sure I could pull it off with a little encouragement. Thanks for asking. I enjoy your video demeanor.

[@JohnnyCANAAN]

I would like to thank you very much for all the videos that you post that makes us understand better our hunting rifles and shotguns and how to fix them and maintain them. Keep up the good job mate.

[@devongunsmith4698]

Thank you