To see a full more detailed repair see link below kzbin.info/www/bejne/hnexfaB_ppmAi5Y
@powertoolsrepair Жыл бұрын
You did that again😊
@doctorlefthandthread Жыл бұрын
I did!! I did this video as the other one was a bit too long for some people
@powertoolsrepair Жыл бұрын
@@doctorlefthandthread to get higher retention rate?
@doctorlefthandthread Жыл бұрын
@@powertoolsrepair yes I do it occasionally I update the video if I think I can do it better with less slow bits and better video quality
@ToolswithSoAlz Жыл бұрын
That's some good stuff
@doctorlefthandthread Жыл бұрын
It works well on these little DCF887 machines
@dawid69146 ай бұрын
What if my DCF887 wont even start? Like engine and led? Like has no power even if battery is fully charged?
@doctorlefthandthread6 ай бұрын
Still worth a try
@dawid69146 ай бұрын
I disasseble this drill and clear pcb on trigger but it still wont start :/ @@doctorlefthandthread
@doctorlefthandthread6 ай бұрын
@@dawid6914 it might be something more serious then it might be beyond-repair
@dawid69146 ай бұрын
@@doctorlefthandthread i do not know how can i check if power from trigger goes to engine :/ mby multimeter?or mby copper coil is burned
@IMPACT-NATION Жыл бұрын
4K and counting my friend. A true grinder of the community💪💪💪. Keep up the good work Paul. We’re here for you brother🤘
@doctorlefthandthread Жыл бұрын
Much appreciated thanks for all your support your comments and others kept me at. Great tool community on this platform Thank you Brandon
@georgedavall94494 ай бұрын
IMPACT-NATION in da House !!!!!!!!!!!!!!!!!! 👍💪✌
@IMPACT-NATION4 ай бұрын
@@georgedavall9449 🫡🤘🤘🤘
@kenwood19711 ай бұрын
You are ruining the bits head! 😢 why not using a manual one philips?
@doctorlefthandthread11 ай бұрын
Sometimes I am rough on the screws that is because I try and move things along quickly for the video viewers not to get bored
@RobinkoelemanАй бұрын
You are a legend. Had the same issue and followed the steps you explained in the video and it’s alive again. Thanks 💪🏻
@doctorlefthandthreadАй бұрын
Thank you for commenting the comments help the channel
@wyattsdad856111 ай бұрын
Mine is doing something similar. In all my years of owning the made in USA 18 volt tools I never once had an issue like this. And I used them daily for my business. Every day for years and years. Thank you for taking the time to make this. My impact is less than a year old. But I don’t want to send it in to Dewalt for service because I use this tool for work and don’t want to wait several weeks or months to get it back. It’s a chicken shit warranty compared to other tool companies. I feel like their new 20 volt tools are partially junk.
@wyattsdad856111 ай бұрын
I’m trying to just spray WD40 around the trigger and now I’m going to use compressed air to try and blow out any debris. If my way doesn’t work I’ll take it all apart like what you did. So far it’s now working normal now since spraying the WD40 in the sides of the trigger and squeezing the trigger a few times. Evidently WD is supposed to be a good contact cleaner. Years back a friend of mine who is an auto mechanic was working on my truck for me and had always used it as a contact cleaner for ignition parts. Plus I’ve read online that it’s a good contact cleaner.
@doctorlefthandthread11 ай бұрын
It should be ok you may have done enough thanks for your comments
@wyattsdad856111 ай бұрын
@@doctorlefthandthread Hi I wanted to give an update from earlier today. So far it has worked. I could tell when the WD took affect, I kept squeezing the trigger while pumping in the WD into the gaps around the trigger. The first two trigger squeezes, same low rpm. Then I squeezed it a few more times while spraying and it came to life. So I sprayed more in, let it soak in for 15 minutes and then used my compressor to blow any crap out of the vents and gaps around the trigger. So throughout the day I’ve been testing it by pulling the trigger and it works how it should now. Hopefully it fixed it. If not I’ll take it apart and follow what you did. Thank you again for making this vid.
@doctorlefthandthread11 ай бұрын
@@wyattsdad8561 you are welcome I would say you have done enough to solve the problem The switch is usually the main issue
@wyattsdad856111 ай бұрын
@@doctorlefthandthread thanks man
@IMPACT-NATION Жыл бұрын
That stuff works wonders huh buddy
@doctorlefthandthread Жыл бұрын
Magic in a can
@georgedavall94494 ай бұрын
Is there a Doctor in da House? Sure is, it’s Doctor Lefthandthread!