How to fix a broken chuck and how to replace the anvil on a Dewalt Impact driver.
Пікірлер: 26
@jorgemolina96952 жыл бұрын
*I absolutely love this set **MyBest.Tools** should have upgraded to the 20V sooner. The impact driver is a must have for driving screws; compact and all muscle.*
@highgroundcomics25254 жыл бұрын
I just wanna say thanks brother. Because of your video I was able the change the anvil assembly for $20. Instead of spending $150 on a new drill. You're the man 🤜🏾🤛🏾✌🏽
@nathandenbow59245 жыл бұрын
Hey man! just wanted to say thanks a lot for posting this video, it was super helpful in the repair of my dewalt impact gun! I really appreciate you taking the time and my repair was a success! Thanks again!
@TheBearGrylz5 жыл бұрын
The chuck spring is dewalt part NO78434. The little steel ball amazon will sell you that does in fact fit is N089668. That ball number is listed black and decker but fits. You might not have to replace the little anvil thing or take apart the whole gun. I just removed the snap ring and the chuck slide itself and that was enough to repair the common broken spring.
@samson63594 жыл бұрын
Very good video for fixing this kind very common problem! You save my time and $$!
@vaguincolombia6 жыл бұрын
good video brendan, just a little thing, if i were you, id have cleaned everything and re-grease everything with new grease it doesnt need much just a little
@bricefletcher96025 жыл бұрын
Thanks man awesome video only one that I found that actually did the chuck and the works got my gun fixed thanks again
@jackhenson2900 Жыл бұрын
Hey Brendon love your vids. FYI I use a mechanics pic to remove the spring. Makes it easier to do.
@BrunoMartinsNeto4 жыл бұрын
I was planning to do it but then I figured out that I need my drill to take out the screws \m/
@BrobMaryland6 жыл бұрын
Im just going to replace the spring lol. I bought the new 20v brushless set. Now i have 2 awesome drill sets with a small repair.
@jimmay2103 жыл бұрын
Thanks for what you do....Lighting was VERY BAD of subject matter!
@langston1aladdin4 жыл бұрын
Thanks. Very helpful. Just did mine today.
@metricstormtrooper3 жыл бұрын
Thanks for the video, just what I needed.
@hhprogressiveconstruction11406 жыл бұрын
I have the opposite problem damm thing never what’s to come out . Thanks for sharing with us 👍 .
@blazerson90686 жыл бұрын
How do you know if anvil is worn out? I replaced spring that holds ball bearing and bit was still not holding well. Should I now replace anvil?
@6530mary3 жыл бұрын
Thank you, very useful!!👏🏻
@JennyAndAlex3 жыл бұрын
This helped. Thank you!
@TheBearGrylz5 жыл бұрын
Thank you for this video.
@azamalmajed40806 жыл бұрын
Please, may you add part numbers of these parts
@nmlindon206 ай бұрын
Why my do just hammering after assembly 😅
@Lifeguruonafence4 жыл бұрын
Is it essential to take the chuck spring out in order to get the gearbox to come apart?
@gerardolopez2773 жыл бұрын
Is the anvil hollow? Reason I ask is because I have a Brocken drill bit in mine
@jordanreece17675 жыл бұрын
You can bend the retainer with a flathead
@TheSrklop797 жыл бұрын
Amazon had this drill in a drill only without battery for $59 ..wouldnt it just be easier to buy a new one...lol
@davidvasey19553 жыл бұрын
Only if you have €59 to through away
@frankviramontes3887 Жыл бұрын
Mine still holds the bit but it just spins won't move would the anvil be the problem then. Tried screwing a bolt and I believe something snapped inside over tighten. Any help is appreciated