Thank you so much for this video. I was trying my 2nd Digirig unit for a second attempt at VHF digital, but this time on a Baofeng instead of building cables for an old Radio Shack HTX-202. I was again struggling, but stumbled across this video and followed it step by step. I was able to work a local Ham on WinLink VARA FM P2P on the first attempt. Thanks again for this video Dennis!! de N9XFX Dennis
@hicksdp Жыл бұрын
Very nice video. I would love to see a similar video for VHF packet for Winlink.
@StephenW1SKC4 ай бұрын
Well done!!! Going to try this myself as soon as I can. Thank you.
@glp2000 Жыл бұрын
This is very helpful information. Helped me understand setting up VARAFM for any radio. George VY1GP
@AI5HV Жыл бұрын
Thank you for the video. It was definitely helpful.
@chrissewell1608 Жыл бұрын
Good video! Can you use a Digirig to work with the Echolink program, to run in Sysop mode?
@digirig Жыл бұрын
Yes, you can use Digirig with any sound-card-based digital modes software.
@JAlbertoDJ Жыл бұрын
You should use VARA FM Narrow. Baofeng does not support Wide mode
@andersgeorgsson2 ай бұрын
I just got the Digirig Mobile and everything has worked well until I go to auto tune and it tries 10 times and then comes back “no signal”. I did the test where I looped AOUT to AIN and ran the WJST-Tune to get a tone and when I had computer set to “m😅motor/listen” - I could hear the tone so I think the hardware all the way to the K1 jack is okay… Any suggestions? 73 de KZ4JN
@digirig2 ай бұрын
If you hear the audio while monitoring through "listen", the radio keys up and you can hear your signal with another radio tuned to the frequency then all all the hardware is performing as expected. You can rule out RF link quality by taking your station to where the remote station is. Also check that the remote station is set for Vara and not packet.
@cwo8771 Жыл бұрын
Will the Digirig allow VARA FM and Winlink connection with a Yeasu FT5D? If so, are the necessary cables available? If you can point me towards a tutorial with that set up, I would appreciate it. Thanks.
@digirig Жыл бұрын
Yes, you can use your Yaesu HT for VARA FM with this cable: digirig.net/product/yaesu-ht-cable-for-digirig-mobile/ The setup instructions are pretty much the same as in this video. General instructions can be found here: digirig.net/getting-started-with-digirig-mobile/
@cwo8771 Жыл бұрын
@@digirig Thank you for the reply! I’ll be buying one soon.
@surplusdriller1 Жыл бұрын
hi i got the digirig from you for my baofeng, but just got an yaesu ft-897 with autotuner that is using the CAT port, do you have av cable that is compatible with my settup?
@digirig Жыл бұрын
You'll need this cable: digirig.net/product/yaesu-ft-8xx-cords-for-digirig-mobile/ If you tuner has a pass-through serial port then you connect radio's 8 pin MiniDin to the tuner and tuner's 8 pin MiniDin labeled "computer" to Digirig. Audio cable goes directly between Digirig and radio.
@markmerriwether2139 Жыл бұрын
What was the purpose of resetting the UV-5R at the beginning?
@digirig Жыл бұрын
This is to confirm that there are no required setting changes that were made off the camera. You don't have to reset yours, but if you are having difficulties I would recommend it.
@markmerriwether2139 Жыл бұрын
@@digirig thanks, that makes sense
@mikekd9bku333 Жыл бұрын
Good information Denis, very helpful, Mike KD9BKU
@arielswings Жыл бұрын
Hello.. Thanks for the great tutorial. Unfortunately, your version of Vara FM is outdated and has a different interface, starting with the PTT item in the Settings menu and items therein. I am using APRSIS32 and can not get the radio to PTT. So far, no joy... Suggestions? Thnx. Cole VA7APZ
@digirig Жыл бұрын
You must be looking at some other software. I've just fresh installed VARA FM v4.2.9 (VARA for FM transceivers) and it uses the same settings as shown in the video.
@kd5you1 Жыл бұрын
You might be looking at VARA HF instead of VARA FM. If your third menu selection under Settings is Waterfall then that is VARA HF. In VARA HF, the PTT is actually in the Winlink Express VARA HF window under Settings -> Radio Setup.
@sanjithnair3266 Жыл бұрын
I have a problem with Digirig whe I am using with Yaesu FT891 and windows11. FT8 receiving is okay but wen transmitting radio will changing transmitting mode but no RF power coming up. I check audio signal on digirig with a headset it is working fine. How can I fix it?
@digirig Жыл бұрын
For FT-891 related information please visit forum.digirig.net/t/cables-for-yaesu-ft-891/16 The post covers the cable connections and suggested transceiver settings.
@audentesfortunailuvat Жыл бұрын
Ensure you set the system audio input outputs to "default". Ensure you set the digirig audio input outputs to "default communication device".
@pixabilly Жыл бұрын
Can this work with only one HT? Why two? Thanks for the video :) 73 de OG3E
@digirig Жыл бұрын
Second radio in this video is just to monitor the transmission. It is not required for the normal operation.
@pixabilly Жыл бұрын
@@digirig Ah, i had to watch that part again, now i saw it 😂 Just ordered cables from your site.
@juozasnarvoisas75165 ай бұрын
VARA.... :(
@TyWooly42 Жыл бұрын
Next time please hire an actor, most of whom understand the importance of Enunciation.