Disassembly and Reassembly SA-22 (FN model)

[@imageskj1]

Thanks for the help! Putting that long spring back into the firing mechanism is a pain I'll agree. I used a piece of tight fitting (oiled) heat shrink tubing cut to fit just below the saddle for the spring tip which allowed the spring to compress in a nice stack and the tip to snap into place. Once in place I cut the tubing off with an Exacto knife.

[@Stray03]

Nice trick.

[@rubenange]

Bonjour merci pour la vidéos ça faisait 12 heures que je voulais remonté le mécanisme et je croyais que j'avais perdu une pièce Merci beaucoup!!😉👍

[@Stray03]

No problem. Glad it helped.

[@conlaiarla]

Very instructive right from the get go .Subbed .

[@aloisioviana3644]

vc me ajudou muito ,muito obrigado.

[@TheWonderman1964]

I have this model too . It is great . Just having problem when I put the 22 lr stinger , it looks the chamber is not long enough, no free bore .The un fired ammo sticks in chamber and I need more effort to take it out . The extractor and spring are in good condition . any way , it fires and cycles all kinds of ammunition .

[@Stray03]

Avoid stinger, It is a bit hard on the older .22s

[@alaindelattin7235]

Does it fire short and 22 long ? Is the chamber the only difference the A model and T ?

[@TheWonderman1964]

@@Stray03 I recently used a BENZ reamer and problem fixed.

[@TheWonderman1964]

@@alaindelattin7235 it shoots LR very well, have not tried short.

[@Stray03]

So was it a dry fire caused problem or overall chamber needed cleaning?

[@alexandergennaro8596]

It doesn't get any better, thanks

[@fernandobeljansky6231]

Do you have any video of how to charge it? Than you very much for this one

[@Stray03]

No I don't think so. There are others out there that do. In this case pull out the follower from the stock, put rounds in the hole in the stock reinstall the follower, then pull back the bolt under the gun since it is bottom eject.

[@mafirearmsafety]

The 241 is basically the same

[@CaravanTirana]

Thanks for sharing this! Can you explain how to remove the butt stock? Thank you!

[@Stray03]

In this one you pull the follower out, unscrew the screw running through the stock, comes out at the bottom where the grip is. Then it should be free to slide out leaving the rest of the mag tube connected to the gun. Look at an exploded parts diagram for a better understanding.

[@CaravanTirana]

Stray03 thanks a lot!

[@leonardoajalla5415]

I have the same carbine and that piece got lost, what's the name of the piece?

[@Joaocouto-z]

I have a rifle similar to this one but out of nowhere it stopped feeding the ammunition, sometimes it feeds but it doesn't close completely, could it be a spring? and all cleaning is up to date on the equipment, can anyone help me?

[@Stray03]

Could be. Field strip it. Clean in check all the parts for damage.

[@Joaocouto-z]

@@Stray03 I cleaned all the internal blocks and greased them with graphite powder, reassembled everything and detailed it here in Brazil, the ammunition comes with a small sera at the tip of the project, so it turns and moves, I have to use fine sandpaper on the barrel to burnish it.

[@wolfgangemmerich7552]

@@Joaocouto-z Pay attention to the chamber : Most 22. lr ammo still use mercury contained ignition components . This components burn into the front of chamber during uncleaned long time use and make the chamber front shrinking . Happen also when this rifel got feed with low pressur 22.lr or 22. short . The System didn`t close any longer completly when the chamber front get blocked with this ,, Mercury coal " dirt.

[@fabianstanciu488]

👌👍👍👍

[@jonsonjonson5619]

hey everyone I have multiple questions, I have x2 of the back half of gun only, I believe both are model 24, and one of each long and short bullet, I need barrels and forearm grips for both, i found a forearm grip for a long 22, but will it fit either barrel?, and my other questions are, I see these adjustment rings, but I see larger single adjustment rings too, are the barrels the same, and will either style fit mine?, i do not have the receiver with the adjustable guts, it's fixed, and no markings on receiver except right under barral hole, there's a patent number or something, one receiver has 4 numbers, the other has 5, are the forearm grips the same for all versions? 24-late241?, my next question is, what parts will swap off the browning sa 22?, will the barrel and forearm grip fit my remington 24? anyone got a barral or two that don't have a bulge 4" up from threads??, i found a complete parts gun, but the barrel has a large bulge in it and i dont want to pay the ffl fees and register something Im going to trash as the serial numbers are on barrel from what im told, thanks for any info

[@Stray03]

Have you checked numrich gun parts for the things you need ? I can't help you with the questions unfortunately.

[@jonsonjonson5619]

@@Stray03 I've been looking around some, I just started, I've been passing on some with MINIMAL Bulging.. and alot are the newer 241 with the plate on barrel side.. wont work.. i was just googling it now, I need for end grip too, so im just fishing.. i need two, a short and long barrel.., yes, i believe I've looked at the place you mentioned, no barrels, I need the magazine tube too, i found some of those .. alittle pricey.. but will probably get one, thanks for the. help

[@nealjobs9755]

Have the exact same rifle... how much do you think it should cost now??

[@woutergijs5246]

In Belgium you can buy these between 50-200€ . Gun law obliges a gun license ( 100$) because they are semi automatic. Sport shooters discard from it.

[@lucaspolk6914]

Remington model 22 version. How do you take stock off?

[@Stray03]

If it is a sa-22 derivative you pull out mag tube follower and unscrew screw that sticks out the mid bottom of stock.

[@Stray03]

over under? I have a video on the Brno 301 shotgun.

[@pepo2k16]

Hello, I want to know how I can replace the tube and the spring that pushes the pellets that goes inside the head (requiring measurement). the model has the burden of bullet above the head , not the side. im from Argentina

[@Stray03]

+Valen Giorgetti So you have the same model as the one in the video?

[@pepo2k16]

+Stray03 yes!

[@Stray03]

Valen Giorgetti I just put a picture of it on my facebook page, you can go see the length.

[@pepo2k16]

i lost the tube, do you know how long is it?

[@pepo2k16]

+Stray03 can you put your facebook link here?

[@nealjobs9755]

Have the exact same fn model... how much do you think it should cost now??

[@Stray03]

Cant really tell you. The browning ones are going for about 500-600 these probably a bit less.

[@nealjobs9755]

@@Stray03 oh okay okay... why are they less than the brownings though?

[@Stray03]

@@nealjobs9755 probably because it doesnt say browning on it. Alot of firearms have that issue. Seems people care if the name is on it more than if the gun works well lol.

[@nealjobs9755]

@@Stray03 actually my gun does have browning patent depose written on it ... it has a walnut finish too... only you have to load it from the top

[@martkbanjoboy8853]

Thanks for the vid, it was very entertaining. I had a mad idea. Do you suppose one of the Norinco clones could be converted to feed box magazines from the top? I realize this may give purists heart attacks. :p

[@Stray03]

martK banjoboy I'd say it could, And if you were going to do that (Assuming I could get a clone for 50$) I'd go with the Calico mags, or an A-180 mag Although it would involve some sight replacement. Could be a cool Idea (only with the clones though).

[@woutergijs5246]

Don’t think so. The cartridges are pushed from the back with that plunjer in a tube. So you would have to be able to feed straight with pressure from the back. I

[@ramcor1042]

I HAVE AN IDENTICAL RIFLE TO YOURSELF. BUY THE TUBE MAGAZINE, BUT IT IS A LITTLE LARGER, AND IT DOES NOT SCREAM, YOU CAN SAY THE LONG AND THE DIAMETER OF THE TUBE MAGAZINE OF THE RIFLE.

[@Stray03]

so you have the one with the hole on the side for loading?

[@ramcor1042]

NO,, MY RIFLE HAS THE HOLE UP THE WALNUT

[@Stray03]

oh you want to know the diameter and length of the tube. I'll do it when I get in from work tonight, hopefully I don't forget.

[@Stray03]

outer diameter approx 11mm inner approx 9.3mm length approx 320mm

[@josemachado4092]

eu sou do. brasil poso. conpra quau eo. preso

[@ericbalbuena7538]

Nesecito una pieza de un rifle igual aese donde la podría conseguir

[@Stray03]

Maybe "numrich gun parts".

[@ericbalbuena7538]

Tendrán los nombres de las piezas

[@ericbalbuena7538]

Ya que es la pieza que va sujeta ala caja

[@blucz883]

My doenst even have loading hole in stock. I dont know why.

[@Stray03]

Strange. Maybe they changed the stock on it?

[@blucz883]

@@Stray03 i know that mag tube isnt original but the stock is. And its hand made by the look. Gun matches but there isnt a Fn on the barrel. Only numbers are same.

[@Stray03]

I know there are atleast 2 models of stock out there. Maybe it is a 3rd one where you just load through the back. There are no holes in the mag tube anywhere?

[@blucz883]

@@Stray03 the mag tube its bought from aftermarket becouse there werent one. My father got it from one man who for 40 years of comunism hunt ilegaly rabbits with it. And it was cheap only one bottle of beer.

[@Stray03]

Interesting story behind it. Ill have to try to find info on that model stock. Ill let you know if I find something

[@likungfuli6963]

Can you show me a top-bottom daouble barrel shotgun?

[@conlaiarla]

That's called an over and under shotgun. The other configuration in double barrelled shotguns is called a side by side. Plenty of videos on KZbin for you to look at.

[@wesroxs2012]

never ever taking the receiver fully apart again.....

[@Stray03]

Went badly?

[@wesroxs2012]

well had some trouble with the springs but if u keep at it it will come together

[@felicianocarbajal4957]

Esto es lomejor de stos rifles calibre 22 browning

[@marcialaviles2761]

K marca es

[@Stray03]

... FN. Fabrique nationale