DIY - 11000mAh Mobile Power Bank 5V 2.4A / QC | Multiple Mobile Charger | POWER GEN

[@candrasniper3404]

Sorry for the correction, the 2200mah is not the "active capacity" that can be used. It usually provides only around 75% of its capacity, because the module is limiting the low voltage of the battery. So the paralel group of 5 pcs 2200mah, if the modul states the low voltage is about 3.2V, the active capacity is around 75%x11000mah=8250mah. The active capacity will be reduced, if the module states the low voltage is around 3,6V. I have done the experiment about it.

[@puucamuntas4813]

how to know if the module states low voltage?

[@kartikeytiwarixiia0579]

@6GDC maybe u should use more thick wires Cuz I was also facing this issue then I replaced wires and now it's working awesome

[@quadplay2591]

@It is finished I had a similar issue, but discovered it was due to voltage loss across the wires connecting to the battery. I switched to heavy guage wire and the proper Nickle strips with tack welding... this stabilized the low voltage cut off which was being affected by wire temperature etc. But overall I still don't like the module as its extremely inefficient. My 15 Ah pack (6 cells) only actually delivers a measured 9 Ah at the USB output due to heat losses in the DC-DC converter.. even when 0% on the module = 3.2v ... furthermore the later versions of the module have an insanely bright LED display and overcharges to 4.28 Volts which will eventually shorten the battery life. ... you get what you pay for !!!

[@explucto]

@@quadplay2591 I've tested the cutt-off voltage on this module, Its 3.6v. Doesn't let the batteries discharge below it. its like 40% of batteries are going unused.

[@юрийфадеев-о3я]

@@explucto и не заряжаются батареи выше 4 вольт,это тоже недобор по питанию

[@kaarthikeyanb7786]

Wonderfull explaination 👍👍👍

[@Cesarariver]

Hi. I hace a question. Only support 18650 1200mAh batteris? Or i Can use 11865 batteries 3200mAh each?

[@rocksildescaguioa1757]

Help me fix my power module why the lcd monitor have low lights and when connected to battery is showing 00 percent?

[@LyLeap]

Having same problem here

[@ВладимирТрифонов-э8ф]

@@LyLeap полное гавно 4 акумулятора заряжает двое суток.

[@lukemm2___]

Módule problem? Battery Low?

[@dolbee3682]

Solucionaron?

[@artofmagic4518]

Very good nice video ❤❤❤❤❤

[@pankajsinghkashyap1912]

What is the maximum charging current (not output current) for this module??

[@powergen522]

2A enough because of excuses amount of current is demage the module

[@silicon-fx1ou]

Whats the point - if it only charger to 75-85% ??? Actually the Charge % is way off - it says 85% while charging at 4.2V (measured to 4.0V Battery Charged)

[@mrgray4703]

Как в плате поменять предел использования акумулятора? Сейчас 3.6-4.1В. Нужно 2.7-4.3 В Какие резисторы нужно поменять?

[@animequiz1796]

i can see, this Module can charge mobile fast, but please tell me how much time did it took to charge all Lithium batteries to 100% ? Please reply sir...

[@sekharlenka3786]

Can we charge and discharge simultaneously?? Brother

[@DianaCaba-l2c]

pls help me to know why that display is not accurate.I have same module.thx

[@silicon-fx1ou]

I tried it. It seems very slow charging time - compared to a simple Lithium Battey Charger. This is a VERY SLOW Charger here. I tried a few tested Lithium Batteries - and they ALL charged SLOWLY - about 1%-2% per Hour with this charger board ! I am Charging on 2nd day NOW with Only 85% and 16%. - These Batteries were charged at much Faster on my Straight 18650 Lithium / NiCad charger - less than 1 Night !

[@jonathandavid8475]

No habrá sobrecalentamiento del módulo por tantas baterías

[@eyefishinggunkchannel1011]

hiya i have just bought 1 of these my energizer 20000mah power bank short circuted and i have loads of single usb modules cos i make mini power banks wnd other stuff but i can never get these up and running dont no why j always blow them up cos i try 2 hard its kindov charging ive tried attaching a 500msh battry and even my 20000mah and it charges a phone for like 3 seconds rhen goes off its not certwin times it goes off do u no ehy his is plz...i am stuvk

[@macrossred1444]

Hello. could you tell me. I bought such a board, but it does not charge my one plus 6 with fast charging. Can you tell me which board to order so that it charges my one plus 6 quickly?

[@shinjansardar9653]

it says qiuck charging while connected to the QC output port but phone does not show any quick charge notification.

[@nahuelespinillo604]

Una pregunta, es normal que cuando la batería está en 0% figure un solo carácter o tienen que aparecer los dos caracteres ( 00% )

[@pepito2467]

estou com uma dúvida, as baterias são colocadas em série, ou paralelo??

[@юрийфадеев-о3я]

Подключаются параллельно

[@Cynth72]

I’ve used that board before, it says it’s quick charge, but each port only outputs 1.6 amps

[@ninomandal181]

I have made the powerbank with this same module with a new one but when I connect my redmi 9 power it shows charging for few seconds but then it turns off but other mobiles or things are charging great. Please reply. What's the solution.

[@powergen522]

First you change the data cable or power bank cable

[@ninomandal181]

@@powergen522 everything is new. And I have taken my friends cable and phone still too the problem is occuring.. Do it occurs in your mobile?what is the name of your mobile?

[@somamondal2451]

My too same problem.

[@savicsasa6161]

I have a question, I want to make a power bank, so I am interested in what is the minimum current voltage for this Battery controller to recognize the 18650 battery?

[@Cynth72]

You only need 1 18650

[@nafisahmuhammad8457]

What is the name of that tape used and where can i find it pls

[@daniella1028]

With this module we can make powerbank with lipo battery?

[@Thedailybikerider]

What is the total battery output voltage? I mean how many volts can the circuit handle from the battery?

[@jamjamnavarro6073]

Can i add more battery?

[@SugandhBatham]

Maine maker bazar se same charging module mangaya h Wo fake lithium battery ko charge krta h Aur usse koi output nhi aa rha sab kuchh try kiya plz help

[@darkshadow57899]

But my working bro

[@kartikeytiwarixiia0579]

My also cut off after sometimes

[@rahuldas3458]

Can I charge 2600 mah x 8 batteries with this module ?? Please reply to me

[@Shreenaath.V]

I used the same power bank board with 4 batteries. But the module is not charging any devices. It detects and charger for a few seconds and stops charging. Would you know what could be causing it?

[@powergen522]

May be board is demaged

[@Shreenaath.V]

@@powergen522 Thank you for the response ji 🙏

[@powergen522]

I using 9 batteries in parallel No problem occurs it perfectly works 3 year

[@sentzzjmr6871]

can i use 3.2v battery ? . becoz i have only 3.2v battery

[@paulb9769]

How are the cells balanced?

[@explucto]

you don't need that in parallel.

[@reshairo]

Thanks for the info. How many battery can connect to this charging board ?

[@mousecursor0]

you can connect how much you want

[@ВладимирТрифонов-э8ф]

Четыре зарежает почти сутки не может зарядить.

[@victorb22622]

Smoke came from circuit while accidently joint revers polarity for 3 second.its working but it is traced that the black component which is right of LED 7 segment display ,is burnt .what is that component .in some circuit ,it has different pins.mine has only two big legs both side of components.i guess it is diode or MOSFET.csn anyone tell what it is ,and what is it's alternate to replace if this component is not available in the market.it is charging but percentage shows not true ,it stuck at 90 or 97,98 not complete 100

[@integer9655]

But brother if i connect any of these usb ports its doesn't show the fast charging indication on my phone display which shows when i connect with my ac adaptor

[@GamerDeMeia]

The board he used isn't compatible with the quick charge technology

[@codesyncr]

@@GamerDeMeia yes it doesnt support qc

[@Fox15-q5w]

Pero que paso con el micro ipad is for charg or not?

[@AsadKhan_78611]

Where can i find the circuit board from?

[@rakeshk771]

i want to recharge 2*3.7v series battery pack. please guide me.

[@melagemer804]

Hlo my 2.4 a power bank modiul is showing out light and mobile is not chargin 😭

[@amsb1234567]

That doesn’t support Quick charge 3.0?

[@anthonydavidr9615]

hey hi i am made this powerbank with this same module but I use lithium polymer battery(4.4v 6000mah) i face a problem that when i charge my mobile that is realme 8 it just charge for few seconds and then the module display blink and the percentage come to zero. when i try with redmi 10 it just charge for few minutes and then automatically it stop charging. but whe n i charge my smart watch or tws is working fine

[@ramkumarbaghel5260]

भाई सेम दिक्कत मेरे साथ थी फिर मैने एक व्यक्ति से पूछा तो उसने बताया कि आउटपुट के लिए 5v चाहिए लेकिन अपनी बैटरी सिर्फ 3.7v निकलती है

[@applepine613]

itu real capacity om? udah di test apa kapasotas database?

[@legendflamez2977]

Super bro.. I also made it It is working

[@electronic7979]

Very nice

[@Nature-lover-36]

Good , well...👍

[@diyexplorer8728]

Cool project bro. Putting this on a decent enclosure might be a good idea also.

[@powergen522]

yes, I will make an enclosure

[@macrossred1444]

@@powergen522 Hello. could you tell me. I bought such a board, but it does not charge my one plus 6 with fast charging. Can you tell me which board to order so that it charges my one plus 6 quickly?

[@georgecarlinn6288]

​@@macrossred1444quick charge reduces battery life fast use it very rarely

[@danishs4049]

How about circuit got heat when charging a mobile..

[@jaatraja7145]

Please halp me ye kha se khrida kitne ka khrida

[@techvlogsph4909]

No bms board needed?

[@explucto]

Not when you are connecting batteries in parallel.

[@maniraj4706]

Super 💥

[@rukshanmaduranga9269]

Did you check charge and dishacarge same time feature ? Is it possible ?

[@pablogeez]

Yes

[@engineerzuhaibhassan1196]

What is the lighting jack

[@AmitSingh-nl7mp]

i made power bank using this module but it is stopping after charging 37% of my phone. plz help

[@thezombieguy426]

Why aren't you balancing the cells?

[@corazonsiniestro]

Se puede con baterías de celular

[@BhartiPatil.]

Good Job!!! But I do think that you should use 2600 mah cells and use 8 cell in parallel this will ultimately increase the backup of the power bank

[@techhacks6166]

Can we use 5000mah cell?

[@BhartiPatil.]

@@techhacks6166 yes

[@kartikeytiwarixiia0579]

@@techhacks6166 5000 mah cells doesn't exists , they are fake

[@kishanmunjapara5216]

Supperb 🎉

[@respect-hm9yt]

Power Bank module battery input Mah supported

[@powergen522]

20000Mah recommend

[@tonevibe9856]

why mine is only upto 98% charge only and not able to reach 100% charge?

[@kartikeytiwarixiia0579]

Solder your wires properly and remove and reinstall battery , mine was also stucking at 99

[@kiranwallapure]

Well, at least I didn't go down without explaining myself first

[@nazmulhassan7008]

Bro it's fast charge the battery.. Or charge as normal like 1.5A Does it support fast charge battery itself.. Please bro reply please

[@powergen522]

it is normal charger power bank max 2A output get in

[@milankaloczi4547]

It shows fast charging, but it charges only with ~1.4A. Not bad, but not the best

[@omkarkhade4602]

​@@milankaloczi4547This module doesn't support quick charge, only normal charge. 5V-2.4A doesn't mean quick charge. For quick charge the voltage should be more than 5V.

[@mbk1251]

Needs a double row of cell to be real world outdoors away home power to last and tgghen indoors over same time as your charging power bank charge via it your phone or tablet going take 10 hour or little less at 2amps

[@titu7860]

realme ke mobile charge karne par 2 mint me hi power bank band ho jata hai aor koi normal mo lagao to chalta kya kiyo aisa

[@kartikeytiwarixiia0579]

Use good wires ( ghar ke board wale )

[@Chandrashekhar_GB]

This power module is waste. My phone not charging, but power bank module showing 100% but not charging and after few minutes 00% showing, i maked this type ( 9:03 )

[@kosabryanyt6937]

ilang oras bago ma full charge?

[@RogerioDiasdosSantos-qz6cs]

Top 👍🏾🔋🔋🔋🔋⚡⚡⚡⚡🔌🕺🏾💪🏾🇧🇷

[@melagemer804]

I connect 4000 ambatter and 6000 am battery but not charging to mobile

[@youngirivboje2366]

How about making a super fast power bank?

[@engineerzuhaibhassan1196]

Lighting input

[@GurvinderSingh75]

What amp output in qc port?

[@MrArt-bh7ls]

Is that curcuit can bear 18650 4.2v batteries,plz plz pl reply meee plz

[@mrcoolinnovator2086]

Yup

[@prashanthkb6101]

Thank you so much for video Please share circuit for 1Amph output

[@pradeepgupta1190]

I have made power bank by same module but as soon as i connect my samsung a 20s mobile for charging , it shows charging for few seconds but again it automatic cut off charging ... why it is so ? Whereas battery is fully charged , mobile is not fully charged

[@powergen522]

may be converter module board problem

[@battleongaming4223]

Is battery percentage accurate

[@powergen522]

yes

[@battleongaming4223]

@@powergen522 okay

[@GurvinderSingh75]

Pleaee tell me how much 5v amp recommended to charge it

[@abhishekbhalerao9174]

Sir 1 kam karo. 20 000 mah ki battery se 4000 mobile kitni bar vharge hoga. Test karake batao. Please

[@syednazmussakib4206]

Why your powerbank draining fast

[@юрийфадеев-о3я]

Почему вы считаете,что ваша музыка всем нравится,засуньте ее себе пожалуйста,сами знаете куда

[@powergen522]

I will reduce it gradually

[@ax-10-god76]

Power bank slaw charge😅😅😅😅

[@jonathandavid8475]

😅me cuesta creer que ese power bank aguante tanto ampers

[@manchestersouthampton9400]

Why did you put the planet's voice?

[@potassiumchloride6968]

This module shuts off when it has 40% or something! is therer any solution for that?

[@OrlyPosadas2015]

Up to how many 18650 batteries can you use that?

[@powergen522]

10000mAh to 15000mAh batteries enough, Because of the above 15Ah batteries demage the module

[@nazmulhassan7008]

@@powergen522 In parallel 50k mah u can add also.. Make sure battery voltage not exceed 3.7v

[@MohamedAshraf-bt3vc]

You mean we can add more battery's ? Up to ??

[@askinsis8768]

184 / 5.000 The module is garbage. battery charging current 500-800ma The charging current for 1 battery should be 1A. When you insert 5 batteries into this module, it will charge with 500-800ma. i.e. 100-120ma per battery. It charges in 30 hours now

[@concealvuellc.5719]

Thank you for the video. How do I add an on/off switch?

[@BhartiPatil.]

@6GDC ok, thanks for telling your personal experience

[@arunkumar-m8n7o]

भाई साहब हमारा पावर बैंक ओपन करने के बाद बंद क्यों हो रहा है

[@BaKan-c3k]

3.7v. 12.v

[@SAMADHANDUDHAL-sw1et]

Can I add six batteries?

[@koluniok3409]

using the module shown on the video you can use only one cell. This is bullshit what he did. You must control the voltage on each cell separately...

[@MattC2085]

I can’t watch your video because of the music. Try rock and roll.

[@arghacreatorexperiments.9054]

Amazing.

[@jumerladera7751]

Pa link sa circuit board sir. Please

[@rishipandey7795]

Ghatiya se ghatiya product bulbul app par aate Hain mangwane per

[@vuli1647]

2.4A output my ass

[@rishipandey7795]

Bulbul sabse bekar app online

[@meme-uu6ry]

Vi prich

[@nurussalama-l2b]

Kak lagunya serem

[@Sworan007]

Most garbage module i have ever used

[@battleongaming4223]

Can you please give it to me as giveaway

[@Кіттоп-ъ9щ]

Какой КПД

[@jonathandavid8475]

😅me cuesta creer que ese power bank aguante tanto ampers