How to make Acrylic Bending Machine from old heat radiator (220V)
Пікірлер: 213
@homemadetools4 жыл бұрын
Good work! We posted this video on our homemade tools forum and people really enjoyed it :)
@IulianMan4 жыл бұрын
Thanks!
@pikifrino5 жыл бұрын
Great job and video too. Thanks for sharing!
@IulianMan5 жыл бұрын
Thanks!
@PeterWest705 жыл бұрын
"GREAT" video...just what I need to make. Thank You!!!
@IulianMan5 жыл бұрын
Thanks! Glad you like .
@sidehop Жыл бұрын
Love the switch to turn off automatically when you bend! Thanks :D
@IulianMan Жыл бұрын
Thanks!
@muskokamike1275 жыл бұрын
One improvement you do is add some square grid lines on the top and bottom so you can be sure your bends are 90 degrees to the edge. If you want tighter radius bends you could narrow the opening above the heating element. You might want to remove some of the pine around the element and install some gypsum (fire code drywall) or other heat proof material.
@Booruvcheek5 жыл бұрын
I would also add something to hold the sheet in place while it's being bent. Some sort of a clamp close to the heater. A strip of metal running across the panel, hinged on one side with a latch or lock on the other.
@muskokamike1273 жыл бұрын
@@Booruvcheek Yeah what I did when I needed a number of pieces bent at the same place is I tacked on a strip of wood at the correct spot, that way the bend line is the same on all of them.
@ahlemguermit66286 ай бұрын
@@muskokamike127إبداع 👌🏻
@Jones1920ac3 жыл бұрын
finally a useful video on KZbin. Good Job!
@IulianMan3 жыл бұрын
Thanks!
@pasqualeventrella43275 жыл бұрын
Bravo.. finalmente qualcuno di furbo su youtube
@IulianMan5 жыл бұрын
Thanks!
@RonInAVan2 жыл бұрын
Nice 👍🏻 looks like I need to go garage selling to find a old used heater so I can build this. Thanks for the video.
@IulianMan2 жыл бұрын
Thanks!
@sonyplayboy25 жыл бұрын
That is the best way I've seen it done by far great job
@IulianMan5 жыл бұрын
Thanks!
@a.prabhakaran70354 жыл бұрын
@@IulianMan ள
@gort55834 жыл бұрын
Great idea love the microswitch power cutout on folding. Make it 12v and it's perfect.
@IulianMan3 жыл бұрын
Thanks! Yes a good idea.
@hyperhektor77333 жыл бұрын
one standalone radiatior tube he uses needs 400W of power, so using a pC powersupply with custom made nichrome wire is possible but you max out the power of the power supply where some cheaper/older ones could break.
@wartono.-676010 күн бұрын
Very very good sir! 👍🏻👍🏻👍🏻
@jonathansimmonds57844 жыл бұрын
My old Tefal mini oven has a thermostat, I think that would be worth keeping too.... The elements are bent to fit in the oven but are soft and can be straightened by hand, I tried with one and it still worked! Can now make a much bigger machine for bending acrylic!
@IulianMan3 жыл бұрын
Yes to make another project bigger and more precise. Thanks!
@sandol8315 жыл бұрын
잘만드셨네요 good!!
@jimmyfavereau2 жыл бұрын
thaks lulian man! nice and simple
@jyotirani82322 жыл бұрын
wow, interesting
@giovannivalarani1254 жыл бұрын
Molto ingegnoso!!!! Bravo.
@IulianMan4 жыл бұрын
Thanks!
@alexandermartinez42393 жыл бұрын
Es el mejor video de maquina dobladora que he visto exelente
@IulianMan3 жыл бұрын
Thanks!!!!
@user-sf8dz4nf7o2 жыл бұрын
Awesome idea!!
@IulianMan2 жыл бұрын
Thanks!
@user-zc8ed6gu5w5 жыл бұрын
좋은영상 올려주셔서 감사합니다
@IulianMan5 жыл бұрын
With pleasure!
@SS-jl9io6 жыл бұрын
Nice idea sir
@IulianMan6 жыл бұрын
Thanks
@SS-jl9io6 жыл бұрын
Iulian Man you replied toi soon😁😁😁
@singleabroad13584 жыл бұрын
Excellent, thank you
@IulianMan3 жыл бұрын
With pleasure! Thanks!
@nhengineer19434 жыл бұрын
Julia, you may find wire nuts are a much safer connection than twisting the wires together; especially with a high load like an element from an electric heater.
@IulianMan4 жыл бұрын
Yes you are right.
@Sor005 жыл бұрын
Omnes ingeniosa est simplex!
@IulianMan5 жыл бұрын
Thanks!
@electronic79795 жыл бұрын
Woow excellent
@IulianMan5 жыл бұрын
Thanks!
@ster97655 жыл бұрын
Well done
@IulianMan5 жыл бұрын
Thanks!
@sampathgamage8615 жыл бұрын
good idea.. useful go head!!
@IulianMan5 жыл бұрын
Thanks!
@asatorhayha5 жыл бұрын
Hi, I know nothing about electricity and that stuff but could I use a fishtank water warmer as a heating element? You know taking it apart and extending the resistance inside, thanks before hand
@IulianMan5 жыл бұрын
Hello, if you want to send me a picture of this device and I will tell you if you can use the resistance or not. iulian.puhace@gmail.com
@user-zs6uz7tr9m5 жыл бұрын
👍
@Proiectediversediy5 жыл бұрын
Fi-ti-ar titlu de ras :) Ai citit titlu si cand am vazut pe radiator NU ACOPERITI AM zis wtf ? :) Dupa aia am vazut numele la canal. Bravo,imi place jucari si mi-ai dat ceva idei.
@IulianMan5 жыл бұрын
:))) ce bine ai asociat, :)) Multumesc, ma bucur. Spor si tie pe youtube.
@dsquaretechnology27945 жыл бұрын
This is very nice products. Generally,If you have small order, This equipment will help lots.
@IulianMan5 жыл бұрын
Thanks! you're right.
@chunhingyap Жыл бұрын
Can it bend acrylic sheet 180 degree like folding or making a U-turn?
@somtingwongwai71943 жыл бұрын
I would highly not recommend using mains voltage for this application unless your country runs 110V or lower with either a ELCB/RCD safety device installed on the mains circuit breaker. its far more safer to use NiCr wire with a DC Transformer.
@shinvaraishinvarai83922 жыл бұрын
100 % true
@midanuna09763 жыл бұрын
God job men 👍👍👍👍👍
@IulianMan3 жыл бұрын
Thanks!
@davidluizmejia39372 жыл бұрын
Genial..
@ezzistudio9604 Жыл бұрын
Good work bro
@IulianMan Жыл бұрын
Thanks
@mariusvlogs92616 жыл бұрын
Tare
@portnovi5 жыл бұрын
Genial...
@IulianMan5 жыл бұрын
Thanks!
@elkinjaramillo66322 жыл бұрын
Hola Cómo haces para que la madera no sé queme sabiendo que en el medio de las dos Maderas hay una resistencia
@welcometomychannelswelcome72616 жыл бұрын
I didn't see you added supply 12v will it take circuit breaker out?
@IulianMan6 жыл бұрын
Hello Well I have not added a 12v power supply for that resistor works at 220v-230v
@michaelgramonte28073 жыл бұрын
Hello.. did you directly plugged it in the main outlet of your house? 220-240v?
@AllVie5 жыл бұрын
Nice video 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
@IulianMan5 жыл бұрын
Thanks!
@srionokartodinoto62853 жыл бұрын
Verry inspirative
@IulianMan3 жыл бұрын
thanks!
@ledmk25 жыл бұрын
Nice idea, cool made
@IulianMan5 жыл бұрын
Thanks! I appreciate.
@relaxyourself1446 Жыл бұрын
Nice
@user-fq7ol9vk5p5 ай бұрын
На 2 минуте заболела голова от музыки и затяжной сборки! Коротко и ясно надо
@jameszx76 жыл бұрын
Iulian Man, so the heat element is connected to power directly without temperature control?
@IulianMan6 жыл бұрын
Hello Yes it is without control. If you have a control, it would be a good idea to put it in
@CesarFlores-xn1vp3 жыл бұрын
Cuáles son los nombres de los materiales que se ocupan para hacer la parrilla o máquina para doblar el acrílico bien inventó saludos desde la cd de mexico
@IulianMan3 жыл бұрын
Wooden board flat aluminum bar switch action switch hinges Halogen tube from the radiator. Thanks!
@angelvaca92322 жыл бұрын
With what name can I find that old heat radiator tube? and which one do you think is better to use of these: .Thermoforming (Infrared Heating) .spiral carbon heating element -carbon fiber infrared heating tube -Nichrome 80-50' - 20 Gauge Resistance Wire thank.
@IulianMan2 жыл бұрын
-carbon fiber infrared heating tube
@christiank.46905 жыл бұрын
Perfekt
@IulianMan5 жыл бұрын
Thanks!
@RT-lz8ey4 жыл бұрын
Hay que poner un regulador de tensión para no quemar el metraquilato y que no se salgan burbujas.
@IulianMan4 жыл бұрын
yes it is a good idea
@ardypamungkas95053 жыл бұрын
Thats using aluminium strip or steel strip sir?
@IulianMan3 жыл бұрын
I used aluminum
@Arek_R.2 жыл бұрын
I thought such large gap would result in much bigger bend radius. Or it would need heating for longer?
@IulianMan2 жыл бұрын
yes the bigger it is the gap result in much bigger bend radius
@TPL0343 ай бұрын
Hi, I would to ask what “voltage & ampere” did you use on a rocker switch is it a “12V & 5A”?
@IulianMan3 ай бұрын
Hello, it is for 230V - 10A
@gs82823 жыл бұрын
I wach this videos because I need bend 6mm flexi glass 90 degree. So looking best choice. For me looks best chose with wire. Or glass heat with gas. I don't know.
@IulianMan3 жыл бұрын
I think both methods work just as well
@Dosonina13 жыл бұрын
How many seconds do you think it takes to hear 1/4th thickness
@IulianMan3 жыл бұрын
I honestly don't know, I'll try and come back with this detail.
@LiveMusicRec3 жыл бұрын
Where can I buy the heating bars?
@IulianMan3 жыл бұрын
From the local hardware store
@hailtonsantana72849 ай бұрын
Bom🤝🏾👏🏾👏🏾👏🏾🇧🇷
@TJ130620105 жыл бұрын
A bit bodgy, but I might use your idea on a similar but a bit more sophisticated project.
@koriremohamed13822 жыл бұрын
excellent
@IulianMan2 жыл бұрын
Thanks!
@nataleamico14185 жыл бұрын
che resistenza conviene usare? quanti wat? Grazie
@IulianMan5 жыл бұрын
from 100w to maximum 400w.
@KWHCoaster4 жыл бұрын
Nice use of the micro switch to automatically trigger the heating element on/off. Hmm, do I really need my toaster oven? It has two of those elements. :-)
@IulianMan4 жыл бұрын
thanks! yes you can use them
@KWHCoaster4 жыл бұрын
@@IulianMan Thanks. I'll have to watch for a cheap toaster oven or check the Goodwill shops for a used one.
@KWHCoaster4 жыл бұрын
@@IulianMan Found a Black & Decker toaster oven today at the Salvation Army thrift shop for $15. It has four heating elements in it.
@yementube33335 жыл бұрын
Good
@IulianMan5 жыл бұрын
thanks!
@TheLoremistress5 жыл бұрын
Great idea. But please ditch the repetitive music.
@IulianMan5 жыл бұрын
Thanks!
@robmcfarlane36024 жыл бұрын
Turn your sound off........simple better than writing a useless comment
@sergeiyossarian5 жыл бұрын
HOW DO YOU PREVENT THE WOOD FROM BEING INCREASED IN CONTACT WITH THE RESISTANCE?
@IulianMan5 жыл бұрын
the aluminum strip stops the heat from reaching directly to wood and the resistance does its job quickly so the wood does not grab heat .
@anka-go40244 жыл бұрын
kreatif banget
@IulianMan3 жыл бұрын
Thanks!
@priyankapanhale61225 жыл бұрын
Denjer video
@sergiocasu7948 Жыл бұрын
Senza un battuta laterale , messo a occhio non viene molto preciso.
@henryvasquez76484 жыл бұрын
Como haces pra que se apague sola al dar la vuelta la tabla ??? saludos
@IulianMan4 жыл бұрын
Well there is a switch there called Snap Action-Switch
@patitolopezg89193 жыл бұрын
@@IulianMan puedes contestar en español, gracias
@vishnupriyadigitals20227 ай бұрын
Price sir
@peppe1955g4 жыл бұрын
BUT YOU CAN FOLD THE BIGGER THICKNESSES ?
@IulianMan4 жыл бұрын
Of course, it only takes a few more seconds until the plate heats up
@noctician5 жыл бұрын
bonjour avez vous des plants ? svp
@IulianMan5 жыл бұрын
Write me an email address and I'll send you some pictures
@amarkumarlavne3055Ай бұрын
power ac hai ya dc
@IulianManАй бұрын
AC
@angelvaca92322 жыл бұрын
what is the name of heating tube ?
@IulianMan2 жыл бұрын
-carbon fiber infrared heating tube
@tinacovington30992 жыл бұрын
Can you please tell me all the materials that you used
@IulianMan2 жыл бұрын
Wooden board flat aluminum bar switch action switch hinges Halogen tube from the radiator. Thanks!
@nataleamico14185 жыл бұрын
la resistenza da quanti wat ? grazie
@IulianMan5 жыл бұрын
400w but you can use even smaller ones
@bertolin514 жыл бұрын
Live wire on wood?!? I’d have used DC
@IulianMan4 жыл бұрын
very well.
@dwierviyanto15534 жыл бұрын
Selamat Malam Sir, saya dari indonesia terinspirasi untuk membuat alat yang ada di video sir, kalau berkenan kirimkan saya material apa saja yang harus saya persiapkan dan langkah kerjanya. Terimakasih
@IulianMan4 жыл бұрын
write me the email address
@ahmad3t4 жыл бұрын
ahmad3t@gmail.com
@helianel.vignoli30233 жыл бұрын
Tem que ser mais perto e mostrar os materiais etc
@IulianMan3 жыл бұрын
Wooden board flat aluminum bar switch action switch
@MrRant2475 жыл бұрын
Wood catches on fire!
@muskokamike1275 жыл бұрын
the heater element is way too hot for this job but as long as he doesn't have it powered up too long, he'll be ok. But it wouldn't take long to start charring and then igniting the pine. It'd be far better if he included the rheostat from the heater to control the temp of the element. I have a strip heater to do just this and it's 10w. That heater element is probably 700.
@richardphatthenguyen1955 жыл бұрын
There's aluminium shield that reflects part of the radiant heat, I guess he could get one polished to make the bending faster so wood gets exposed less with the temperature gradient.
@muskokamike1275 жыл бұрын
@@richardphatthenguyen195 the easiest way would be just add a controller to turn down the wattage of the element. But if he wanted more precise bends (aka a narrower radius) he could narrow the opening by using an L shaped piece of aluminum. But aluminum is notorious for being a good conductor of heat. In addition (having worked for a plastics fabricator for years) you should be heating both sides of the acrylic. It takes the stress out of the bend. It's a good basic design though. Great for making the occasional bend or piece.
@IulianMan5 жыл бұрын
Hello, @Muskoka Mike Yes you are right . I thought about this but after I did the video :)). It was fine with an intensity adjustment for acrylic boards of different thicknesses. At the thin ones, it is good to give less power. Thanks for the tips. I will try to make a more perfect device with more adjustments, not that bassic. Thanks!
@IulianMan5 жыл бұрын
Hello, @Richard Nguyen Yes it is true . Thanks !
@hedy8475 Жыл бұрын
那是甚麼燈管
@IulianMan Жыл бұрын
It is a heating element that also emits light.
@promo_vip Жыл бұрын
show
@acspinelli15605 жыл бұрын
Não consegui fazer um igual a esse, comprei o da Tagalu, da uma olhada nesse vídeo, kzbin.info/www/bejne/a6m2nn1meLOeiq8 , funciona mesmo, ficou fácil dobrar as peças, tem ate controlador de temperatura, é bem simples de usar.
@IulianMan5 жыл бұрын
Yeah, it's cool Maybe I'll do something like that to make it easier
@POSdesing5 жыл бұрын
вот видел я хрень . но вот такую.... я б хотел увидеть, как этот чимпион согнет 10 подставок чтоб они были одинаковые. Кто будет делать гибку , так делать не надо.
@user-ui2nx9ht9z5 жыл бұрын
я даже знаю где ты увидел хрень. В зеркале.
@POSdesing5 жыл бұрын
@@user-ui2nx9ht9z В своем зеркале я вижу гибгу которая согнула тысячи подставок, а за это меня бы кознили, а пожаник если увидет то и над телом надругается.
@alirazaraza97615 жыл бұрын
Galit traka ha ya .
@IulianMan5 жыл бұрын
Hello I do not understand what you mean
@alirazaraza97615 жыл бұрын
Sorry for comment u
@parvezbaba76715 жыл бұрын
estrike se kach val sak ta he
@H2Dwoat5 жыл бұрын
Started to watch the video but had to stop, music was awful, too loud and distracting. I have saved it to watch later without sound, hopefully I won’t miss any narration. Interesting topic in its own right no need for the music.
@IulianMan5 жыл бұрын
Hello yes, music is free from youtube and it's not great. Sory If you have any questions, I can help. Thanks
@H2Dwoat5 жыл бұрын
Iulian Man no need to apologise, my comment was meant as feedback. I appreciate the legion of people that use their own time to show me interesting things and give me the opportunity to learn new things.
@IulianMan5 жыл бұрын
@@H2Dwoat Thanks!
@alit.60695 жыл бұрын
Wrong design.wood will be fired.you need to use non flammable material
@IulianMan5 жыл бұрын
For Acrylic glass it takes a few seconds to warm up to bend it. To burn the wood takes a few minutes because the aluminum bar is still protecting it. so there is no fire at all. But your idea is good too. Thanks!
@alit.60695 жыл бұрын
@@IulianMan it is ametour design. maybe it can be acceptable but you are walking close to danger.İf you forget it then it will be fired
@robmcfarlane36024 жыл бұрын
@@alit.6069 Thats why he installed the reed switch so that it turned off when you started to bend the perspex.....if you use power tools use common sense and supervise the tools you use, It is a crude tool made to get the job done.......if you want to spend more time to make it perfect go ahead.
@TVF-723 жыл бұрын
Пожароопасненькая штучка :((...
@EVgenrator5 жыл бұрын
Очень пожароопасно! Не рекомендую повторять. Или применяйте металл вместо дерева.
@IulianMan5 жыл бұрын
know that I used it for more than 10 bendings one after another and no trace of fire or black wood ...
@EVgenrator5 жыл бұрын
Не забывайте выключать !!!
@the.n00bish5 жыл бұрын
Great Idea, execution not so great, wood on something that radiates heat? BAAAD IDEA, yes it may only get used short term, but think about the doofuses out there building that thing 2. No Soldering? again, bad idea... cutting before measuring.... meh
@IulianMan5 жыл бұрын
Different opinions are welcome. Thanks!
@myfinalheaven95904 жыл бұрын
It's a proof of concept. He's showing us that it works. Also, in order for the wood to burn, the heat would need to do two things: 1. Get through the aluminium 2. Be hot long enough for it to get through the aluminium in order for the wood to burn, which is why he added a reed switch to disable the power when the acrylic is being being bent. Also, he just showed that it works without soldering. If you're going to use any type of power tool, common sense and caution are useful too.
@tech-u-train80034 жыл бұрын
No speaking
@IulianMan4 жыл бұрын
:)
@brianross72335 жыл бұрын
The music is awful! Ruined the video
@IulianMan5 жыл бұрын
I will try to change it.
@sylviaknutcecily4 жыл бұрын
Then mute the audio like I did. He doesn't say anything, so no need for audio.
@germancelis51532 жыл бұрын
LO IMPORTANTE ES EL CONTENIDO... SILENCIA EL AUDIO Y LISTO.
@alirazaraza97615 жыл бұрын
Fake
@IulianMan5 жыл бұрын
what seems to you to be fake?
@edism5 жыл бұрын
@@IulianMan He mistook your video for his scrotum, don't worry about him :)
@IulianMan5 жыл бұрын
@@edism :)))))Thanks!
@edism5 жыл бұрын
@@IulianMan you're welcome bro, I appreciate the upload.
@A.A.BZ.075 жыл бұрын
👎👎
@TheMourningLight Жыл бұрын
This videos screams “Crafty Panda”… crap music and a 78% chance of electrocution.