DIY EGS002 use TLP250 | NextPCB

[@PhdHung]

file: www.mediafire.com/file/1sfyfspemya2bve/File+EGS+TLP250.rar/file

[@bankzaclub02]

Giá trị của J2, J3 và J4 là bao nhiêu?

[@PopeyitoRD]

The video I was waiting for, just in case, you won't have a video to make an inverter and charge the batteries too, in my country that way is used a lot

[@luiscarlosmarques3946]

Excelent idea. This stage with TLP250 protect the eg8010 from surge or any malfunction. Is an isolator.

[@yuribiktop6595]

@Homemade , Nice job but TLP250 gerber files is there what about the main board gerber files?

[@PhdHung]

waiting for the next video tomorrow :d

[@yuribiktop6595]

@@PhdHung Thank bro, i can't wait to have it. Can charging function be included is very essential to have it in the circuit?

[@yuribiktop6595]

@@PhdHung still waiting bro

[@yuribiktop6595]

Can it be use in your previous Egs002 main board projects?

[@Dc_tech386]

I first thought the eg8010 was a positive output signal but as I look good at the tlp250 design circuit diagram I see that the all 4 signal or negative frequency output as in pulsing ground that’s why the pnp or use for amplifier frequency

[@dinelsonmarcelino]

hello, congratulations for the project and for teaching, pass on for your experience, I am an admirer of your work, I live in Brazil and here we don't have these good components at an affordable price...

[@giorgosleros1525]

can I put tlp350 instead of Tlp250? will it work?

[@yenphi4600]

Có bán mạch hay PCB này không bác ? Thay thế tương đương egs002 của china luôn phải ko

[@PhdHung]

co bán b. thay thế egs002 đó b

[@yenphi4600]

@@PhdHung xin link mua đi bác

[@satd2024]

In file it shows controller is ATMega8 & in video it is EG8010.

[@danieladusei573]

Hello sir please can you please tell us where we can get EGS002 because I bought one from AliExpress but not working

[@ducducdientu]

Hóng anh dùng mạch egs004😁

[@PhdHung]

Có mạch dùng stm8s003f3p6 rồi, có cả sạc và màn hình, nhưng tình hình chip arm dạo này cực kỳ căng, ko có hàng mà lại đắt lòi ra. làm ko có lãi mấy nên tạm gác lại đã.

[@ducducdientu]

@@PhdHung bây giờ dịch bệnh chán thật ạ😅

[@adesuyisunday4287]

Wow, it nice and good project. Is the 8010 ic already preprogrammed or you remove it from egs002 board?

[@yuribiktop6595]

Please answer

[@God_controls_all]

SMH! EG8010 is an ASIC. If you can't take the time to read the datasheet, then don't expect an answer to such trivial question....

[@yuribiktop6595]

@@God_controls_all the spokesman

[@daberechinwobi6492]

Circuit diagram please

[@yuribiktop6595]

At what temperature do you use for soldering the smd to avoid destroying the smd components?

[@PhdHung]

~300°C . I use tin Sn63Pn37 . Melting temperature 183°C

[@avichalid5604]

Great work how can I get the BOM list? Thanks.

[@adil_3x929]

great project sir you always impressed us, thank you very much. sir you have an old induction heating project i would like you to do a powerful project for welding copper pipes if possible.

[@nazimseydametov5901]

Hi, great job! you can give gerber to the ph002-tlp250 board?

[@avichalid5604]

Thank you for the Great project, is there a way to get the BOM with the value of the components? Thanks.

[@chrisgrim374]

Great pcb . Do you have the pcb file lay out please.

[@daberechinwobi6492]

Can I use it in ferrite inverter

[@adesuyisunday4287]

Hi, when are you going to do this sinewave inverter that also charges battery and have LCD using STM8s003F3p6 ?

[@uzairaezad7630]

Which pcb designer do you use for these projects?

[@abulhassanqadri00]

Sir use atmega8 or 328 chip?

[@PhdHung]

EG8010

[@abulhassanqadri00]

@@PhdHung sir replace with atmega8 chip?

[@bashiralao9172]

What software can I use to open the schematic

[@chandansaini3057]

Why tlp 350 is not work with eg 8010

[@vanderpereira3923]

Why was this file link blocked?

[@Davidslabofficial]

Awesome i was waiting for it Thank you

[@jahirulislamshovon9256]

how many mosfets can it drive without totem pole?

[@PhdHung]

16 mosfet bro.

[@jahirulislamshovon9256]

Can it run 16 big mosfets or small mosfets without totem pole ?

[@listener1940]

Circuit board file not getting...not reachable as of in the description

[@PhdHung]

file ok

[@tranlang]

Ko mở bán nữa à ad

[@vctech4954]

Sir please share tlp driver circuit digram

[@d.i.yelectronic8592]

A cho em hỏi con vdk mình mua có code sẵn hay tự viết ạ

[@PhdHung]

Có sẵn rồi nhé. Khoảng 25 30k 1 con.

[@Aaaaaasssssss382]

excellent. do you have your own program (microcontroller) or you retrieved it from old pcbs? i need the program.

[@brianbaird6528]

The EG8010 is an ASIC. That stands for Application Specific Integrated Circuit. It is not programmable. It is hardwired internally to do what it does. You choose various options by how you hook it up, and once you power it on, it just starts working.

[@mayoo7968]

friend , the link is not working

[@lymmentrixprofessional]

Thanks very very much, this is what I've been waiting for, but what about the coding of those IC and chip

[@aravindadas567]

is 8010 ready preprogrammed?

[@brianbaird6528]

it's not programmable. It is an ASIC which stands for Application Specific Integrated Circuit. You choose a few options by which input pins are shorted to ground or to 5 volts. Then you put power to it and it works.

[@bankzaclub02]

ด้านบน EG 8010 และด้านล่าง ตรงตัว J คือตัวอะไรค่าเท่าไร

[@hieuvuminh2162]

mạch này có bán k anh ơi ??

[@PhdHung]

Có bạn

[@Charlesbenicio-ap]

Onde fica o circuito tempo morto?

[@brianbaird6528]

It's part of the EG8010 chip. On the EGS002 board (which is junk if you ask me), there are 2 jumpers that set the dead time. I don't know if these are included in this improved version. This board may not be adjustable.

[@nguyenvanthuong7153]

Cái đẳng cấp này ngang tầm thế giới chưa anh? Trình cở này chắc cái máy hàn 850k của e anh nhìn cái vẽ được ngay

[@PhdHung]

Vẽ chơi chơi để quảng cáo cho bên làm mạch thôi b

[@ravishekhar6388]

Excellent project bro... Your plastic parts drawer is looking nice and i need one like this.. Can u please share the purchasing link of this...

[@rehancd100]

Hi dear need email this files Download operation failure

[@md.arifulislamarif8077]

Very very nice project sir...💓💓💓💓💓💓💓💓💓💓💓

[@HaiNguyen-kv2fq]

A vẫn chưa mở shop ạ

[@yannis92preloude]

Hi . Would you share your gerber files.

[@engr.makabirarif722]

give the circuit diagram

[@adityajadhav4321]

This all components from given wapsite It cannot be delivered to my address in India

[@MarcosVinicius-cw6sw]

Boa noite a minha EGS ela não aparece as mensagens não display e eu comprei tudo junto e a minha placa para botar em 60 ela tem tipo um capacitor ou é um resistor no outro borne de 50 tem como corrigir isso

[@brianbaird6528]

You did the 50 to 60 conversion wrong and may have damaged the board. You must REMOVE the jumper from the 50 hz position and then INSTALL it in the 60 hz position. All the jumpers are like that. If you can't replace the jumper, you can bridge the correct solder pads with a blob of solder in the correct position. Do not do this without removing the jumper from the other position first. Be sure of your positions, or you will cause a dead short and may burn the board.

[@ridoo61]

We like your awesome work. 😍👏👏👏👏👏👏

[@bashiralao9172]

I think buying will be cheaper than DIY

[@PhdHung]

Very few people sell it.

[@satd2024]

Very nice and very useful 👍. Thanks a lot.

[@ДаниилДобринский-о3з]

Привет, твоя плата совместима контактами с прототипом? Куда делись 2110? Белые коробочки это оптроны?

[@brianbaird6528]

The white boxes are TIP250 mosfet drivers, which are better than the 2110 or 2113. I hope this guy can build a better board than the EGS002. I have tried to build an inverter twice and the EGS002 has burned out the same two mosfets both times. I can't tell what the problem is. Maybe the EG8010 chip is junk or (more likely) the 2113 mosfet drivers.

[@HaiTran-pw4rn]

Mạch này anh tự thiết kế mà sao có tấm đó vào chì hay vậy. Như là sinh ra dành cho nhau ý😉

[@PhdHung]

đặt làm stencil mà bạn. lấy lớp top rồi bảo họ cắt stencil cho.

[@electronic7979]

👍

sao làm dc cái tấm thép kia vậy bác

[@PhdHung]

350k đấy :)))

[@PhdHung]

Bạn đặt nhà máy nó cắt cho.

[@haiidol4301]

càng ngày càng hiện đại quá anh

[@PhdHung]

Video quảng cáo thôi mà 😐

[@MultiBwee]

Amazing , God bless you and award you with longer life , we appreciate you

[@Khoaitaymientay]

Đợi bo này lâu lắm rồi

[@dientu97]

Úi a nhiều tlp250 thế trk e chạy quah mấy tiệm linh kiện mà k có

[@PhdHung]

bán nhiều mà b

[@dientu97]

@@PhdHung bữa em mua để làm cái mạch hàn cell của anh ý. Cả aitiny13 ssu cả tlp250 đều k có nên jo vẫn chưa xog :)

[@kdcreativity6201]

amazing 🤩

[@PhdHung]

Thanks

[@robertogaido2539]

Hi bro can you send it to me Gerber???? thanks

[@har2191]

Hello friend, I am a fan of your KZbin videos and I admire your intelligence to create things. I want to buy a project from you, the EGS002 module, I want to learn how to make the board and program the microcontroller, I need the code and if it is an Arduino, much better. Greetings from Ecuador, I await your response.

[@JAMEsAMTECHCHANNEL]

Watching

[@PhdHung]

🙏

[@akindiranolanrewajujohnson1873]

great job... working ideas

[@PhdHung]

Thanks bro

[@pedropaulo-ot4dc]

congratulations

[@bisnetodeportugues]

SMD circuit. Very Hard. Many do not understand This Technology.

[@jahangirali2351]

Dear i want this plz

[@alfajranmotorternate]

very good

[@PhdHung]

Thanks bro

[@suaamthanhmaivinh1776]

Bán pcb ko a

[@PhdHung]

có bạn à

[@suaamthanhmaivinh1776]

@@PhdHung để em mấy bo về ngiên cứu

[@quanghoang04]

👍👍

[@MohsinAli-ov5ow]

Bravo..

[@user-tn1hk6zm2freedom]

Cost more to build it then it would to buy it.

[@brianbaird6528]

If you can find a place to buy his version or something like it, please reply to my reply and let me know where I can buy it too. I have tried the cheap EGS002 boards from Amazon and the inverter blows up (yes, the mosfets split open and or catch on fire) after an hour or two of use. No, they are not overheating. Both times, the mosfets had never gotten above finger-touching temp. Both times this happened, it was when the inverter was starting up. Both times, I started and stopped the inverter just fine many times, then all of a sudden I turn it on and pow-stink. The first time I blamed it on my trying to start up a 5000 BTU window air conditioner. But the second time, I only had a little 15 watt incandescent bulb on it.

[@muratyasar7916]

bravo süpersiniz

[@muratyasar7916]

türkiye sipariş yes

[@ShakeelAhmed-ft2mx]

Nic projact bro

[@PhdHung]

Thanks bro

[@MrGeraldino250]

very nice man genial

[@muratyasar7916]

SATIYORMUSUNUZ.

[@petername2608]

Super bro

[@naiart7403]

Get help design circuit dc to dc boost converter mppt solar shell dc input 100-400vdc to output 300-400vdc adjustable volts.

[@danieladusei573]

I mean the MCU

[@Dc_tech386]

I wise this gun could replay to is subscriber

[@ahmadrevaldi2986]

First