DIY Evil Crow Part #1

[@moormoor4281]

Thanking you most kindly from England UK

[@WorkFromHome-th2eq]

Hello England, you are more than welcome

[@HackDraw]

which bin file upload to esp32 WROOM?

[@Pookie-ce8kb]

Have you been able to use it as a key fob signal transmitter and receiver other than having to jam and copying the signal ?

[@troyapostolides5550]

Hay u done a build on the esp32-s3 t display touch screen with cc1101

[@Niche_skills]

👍🏻 Please upload Part 2

[@paranoidzkitszo]

Please update Part 3 thank you. Great content by the way. Very smart. Thank you for sharing.

[@SathilaPerera]

Hello sir, I created your evil crow rf esp32 project. But when I test it with Nissan leaf 315mhz key fob '007 yuul 0453', when I go to wb page 'Scanner' menu and activate it, even before pressing a button on the remote (301mhz , 302mhz , 300mhz , 415mhz , 433mhz , 915mhz ) showed continuously. However, after I selected 315mhz, cc1101 setting and went to recode or rolljam and activated it, the code related to that remote was not shown when I pressed any button on the remote. Hope sir help me to make this right. I am a school going student. Please help me create this. thank you.

[@WorkFromHome-th2eq]

@@SathilaPererahave you checked cc1101 module ? It is very sensitive. It could be broken.

[@SathilaPerera]

@@WorkFromHome-th2eq Is it possible to rolljam Nissan leaf 315mhz key fob '007 yuul 0453' with this? 315mhz frequency will jamme sir.

[@WorkFromHome-th2eq]

@@SathilaPerera it is possible, if you have sdr dongle you will know the exact freq. It could be not 315Mhz precisely.

[@alanvaughan5366]

do you have a video on the instalation of the main software to the evil crow 2 please

[@moormoor4281]

Fantastic achievement

[@dsrb5467]

Bang untuk module 2 cc1101 terhubung ke gpio mana pada esp32 bang, itu yang di deskripsikan untuk module 1 bukan module 2

[@nobodynoone2500]

Nice work!

[@WorkFromHome-th2eq]

Thank you! Cheers!

[@xprisyt2702]

Hello, I am following your projects, they are very successful. I have a question, there is a rollin code barrier gate. It is around 434mhz. At what frequency should we set the brda cc1101, that is, it should copy 433.92 mhz and similar frequencies?Thanks.

[@WorkFromHome-th2eq]

I think the setup of 433.92 can also copy the frequency of 434. I did try to my electric bike alarm which works on freq 434mhz and success to turn it off in my case

[@xprisyt2702]

@@WorkFromHome-th2eq Thank you for your answer. I want to do it with 1 piece esp32 +1 piece cc1101 and sd card. I do not need a jammer. In this way, whatever code I upload from github will be enough. I would be glad if you could help me with the link of the code.I have a question. Are the 433.92 MHz frequency logs it reads recorded on the SD card?

[@WorkFromHome-th2eq]

@@xprisyt2702 you visit wfhstudio github I put all the code of my projects. Yes you can save the signal in the sdcard

[@WorkFromHome-th2eq]

@@xprisyt2702 you can find the code in my github : wfhstudio

[@xprisyt2702]

@@WorkFromHome-th2eq Thanks.

[@miaexo1482]

can you upload web interface ?

[@paranoidzkitszo]

They do - go to the page adddress mentioned in the video(can't remmember the time...just watch again till you find it- it's there)

[@SiKodot]

Can i use cc1101 v2. 0 or Ti cc1101?

[@مالتيگو]

Part 2 ❤

[@benmeddourabderrahim9837]

salam nice work . i tested and it work fine .and can you please give me the button wirring its not clear and battery wirring pls

[@WorkFromHome-th2eq]

I will make a picture tomorrow so it would be more easier to see. Anyway, glad someone made it.

[@benmeddourabderrahim9837]

@@WorkFromHome-th2eq thank you some much for you i will wait for you and for you nice project good luck

[@WorkFromHome-th2eq]

@@benmeddourabderrahim9837 check description I put the link there

[@benmeddourabderrahim9837]

@@WorkFromHome-th2eq thank you it work fine😀😀

[@WorkFromHome-th2eq]

​@@benmeddourabderrahim9837excellent

[@SiKodot]

Bang ini pake esp32 Dev kit atau Dev kitc v1 atau Dev kitc v4

[@roslinda3492]

bang kenapa wifi nya kadang reset sendiri?

[@anthonystojcic9110]

Hi, can you share this web interface ?

[@kursadzeybek356]

can i OPEN the car keys all aroun me with this device...???

[@WorkFromHome-th2eq]

As long as you know the freq .. yes you can.

[@toxicc4177]

hello, i flashed the same firmware on my diy and the website spams Tesla EU signal sent continuously and it doesnt stop, did you encounter this problem and how did you fix it?

[@jamierispin7080]

Connect your buttons

[@privatelifeofbetasquad9480]

​@@jamierispin7080can we do without buttons?

[@privatelifeofbetasquad9480]

Did u get any solution same problem with me

[@senrio2003]

hi hope u will be ok i just wanted to ask that can i make the main device from wemos 8266 or i have to use esp32

[@WorkFromHome-th2eq]

Have to use esp32 mate.

[@Simonrilley812]

@@WorkFromHome-th2eqcan you do mousejacking on it???!

[@michaelzborovan4362]

@@Simonrilley812 only if the nrf24 module is added

[@Nickq-me]

Can you teach me how to install them all, like 2*cc1101 rolljam, if it's not convenient, that's fine, thanks!

[@WorkFromHome-th2eq]

I think in the description, the wiring is explained ... Nick.

[@Nickq-me]

@@WorkFromHome-th2eq So it can be used with firmware h-rat right?

[@Nickq-me]

@@WorkFromHome-th2eq I suspect using 2*cc1101 in one device can do anything if i use roll jam Do you need 2 devices?

[@WorkFromHome-th2eq]

@@Nickq-me yes you will need 2 devices for rolljam. The 2nd device is for jammer and it will connect to the 1st device by inserting IP address.

[@WorkFromHome-th2eq]

@@Nickq-me yes it can use h rat firmware

[@gianniiky7899]

hi my friend good job.

[@WorkFromHome-th2eq]

Thanks for visiting

[@WorkFromHome-th2eq]

@@gianniiky7899 better you give me your email, mate

[@gianniiky7899]

@@WorkFromHome-th2eq Bro do not forget me

[@WorkFromHome-th2eq]

@@gianniiky7899 no ... bro

[@gianniiky7899]

@@WorkFromHome-th2eq ok tks

[@lochobhai]

Your any discord server

[@roslinda3492]

halo bang, knpa wifi evcw nya kadang resett???

[@WorkFromHome-th2eq]

@@roslinda3492 masih mainan evil crow ... Ada 2 sebab pertama power kurang atau esp32 udah lemah

[@roslinda3492]

@@WorkFromHome-th2eq apakah bukan karena SD card nya?

[@SiKodot]

Bang bikin video cara buatnya pliss

[@spr-x]

tanya bang, ini modul 1 sama modul 2 pin nya bisa di pararel di pin yang sama?

[@WorkFromHome-th2eq]

Bisa sesuai wiring yg ada di deskripsi

[@spr-x]

@@WorkFromHome-th2eq ok bang, makasih. Nunggu part 2 siapa tau ada source codenya bukan bin 😁

[@SiKodot]

​@@spr-xini source codenya gabisa ambil dari evil crow nya ya?

[@spr-x]

@@SiKodot dari github h-Rat udah di hapus source codenya beberapa bulan lalu. Tinggal nyisa yang lainnya.

[@zrlcproject]

cara update firmwarenyta gimana?

[@tonkofonko]

Great please make full video tutorial with code.

[@WorkFromHome-th2eq]

the code can be found in the github link in the description. I just made from the existing code from h-RAT

[@tonkofonko]

@@WorkFromHome-th2eq Ok thank you :D have a nice day.

[@SiKodot]

​@@WorkFromHome-th2eqdo you use source code from h-rat officially? Did it work?

[@tonkofonko]

Hello dear wfhstudio original H-RAT github repository for this code is not awailable. Can u make v2 or better functionl code ? I mean like Saving all captured to SD or similar or more advanced methode.

[@tonkofonko]

When I try to upload .bin file using ElegantOTA web interface, it works and upload correctly but when its finished esp32 just restard and firmware cant be saved.

[@memesedikitreceh]

bang wiringnya boleh minta dalam bentuk gambar, saya agak kesulitan baca wiring dideskripsinya 🙏😅

[@privatelifeofbetasquad9480]

I did it I will upload

[@SiKodot]

​@@privatelifeofbetasquad9480where

[@ahmaddanish2307]

firmwarenya dowload dimana bro?

[@WorkFromHome-th2eq]

@@ahmaddanish2307 ada infonya di vidio bang

[@Danielle97165]

What language is this please ?

[@WorkFromHome-th2eq]

Bahasa Indonesia.

[@AOXZALL-gs9ix]

Bg buat eviltwin menggunakan node mau yg bisa Deauther all

[@WorkFromHome-th2eq]

Kalau yg deauther all bukan Evil Twin ... Deauther dari Spacehun ... jadi khusus untuk Deauther aja. Kalau evil twin dia spesific 1 SSID krn kan Phising nya hanya 1 yg di deauth aja gag bisa barengan. Kalau deauther all sepertinya ASP 29 udh pernah buat tuh di channelnya

[@AOXZALL-gs9ix]

Sy udh pernah makai punya asp itu yg 1.4 cuma nga tau knp setelah sy instal di esp sy itu tidak stabil gt

[@AOXZALL-gs9ix]

Nga tau knp mas pdhl klo awal 2 stabil truss skitar 20menitan nga stabil kek pengaturan nya g keluar truss evil twin nya nga muncul phishing

[@AOXZALL-gs9ix]

dan kendalanya setelah sy instal ke v1. 4 sy install fw ke 1.3 versi sebelumnya error di v1. 3 nya nga muncul apa2 pdhl sy sudah yg versi pro nya wkwkk mnya minta di abg klo ada waktu jd skrg esp itu udh g bisa di pake fw asp itu lg jd klo make fw yg lain selalu stabil

[@menyulofficial8040]

Ya bang,bikin deauther/evil twin yg hidden ssid donk.