[DIY] 👍Fantastic Enclosure for Powerful Laser Engraver ORTUR Laser Master 2 Pro S2 / WOODWORKING✅

Awesome Enclosure DIY for Powerful Laser Engraver
ORTUR Laser Master 2 Pro S2
Creating an enclosure that allows you to use the laser engraving machine quickly and safely in a variety of ways
12mm birch plywood is used and the handle is paduk wood.
Please support me by subscribing and liking!
I am CarpenTAK from Korea.
my favorite tools.
Ortur Laser Master 2 Pro S2 SF
&LightBurn software
This is a sponsored video. When you click the link below you will receive discount from madethebest.com. Thank you for your support.
Buying link: bit.ly/3te1Q5b
Coupon : CarpenTAK
Discount :10$ off over 99$
and Amazon store: amz.fun/6AbML
Please support the channel by becoming a paid member. Your support helps us create more exclusive content and improve video quality. Thank you for your support!
/ @carpentak

[@Aalehaaner]

Wow. This is the best I've ever seen. Much more sophisticated than the original box. Thanks for the great video. Best regards from Thailand.

[@attilah]

My favorite moments in all your videos are when you say: "Okay" :-)

[@grumpyshorts1056]

A man that takes the time to do it right!, and takes pride in his work! A sweet enclosure!

[@danielroos5993]

Amazing and you make it look so easy 👌

[@Ali36999]

Excellent and smart

[@MARCELLO6859]

Really ingenious, great work!

[@irawansujanto]

Just WOW ! Amazing. The best Enclosure OLM2 I've ever seen.👍

[@joshualewisjones]

This is incredible. In awe of the creativity and as attention to detail. Keep up the amazing work!

[@GabrielaGonzalezMeade]

really nice!

[@TubeDaLube]

Clever 👌I think this must be the best cabinet for a laser i have seen,great design 😊

[@Jecosheila]

Great job on the enclosure! Love it!

[@gabrielestupinan]

You have de best workflow I have ever seen and the most accurate finishing wood made. Congratulation!

[@MrRicksilva]

Thanks for the idea I will try to make one for me, great enclosure. Well designed.

[@tonygagey]

Best enclosure I have seen bar non, masterfully constructed too ! Extremely well done all round!!!

[@carpentak]

Thanks for the wonderful comment.

[@holgerbauer8406]

Great Box! Thank you!

[@stefankrimbacher7917]

Best enclosure ever seen.

[@josefforer8300]

Whow, I was so inspired that I adapted your sophosticated approach to the TwoTree Laser Model S2 ... and it works fantastically...greetings from Vienna

[@georgbrunenberg8007]

Amazing, what a great idea and what a great job

[@Jay.C.H]

Excellent ideas. It seems that you have covered all the bases, except for good veneration. The exhaust fan is underpowered if you are trying to blow more than a few feet. The longer the run, the more power is needed. Air drag in the tubing is the issue, but that is an easy fix. Great design. I like your gridding idea, it is perfect, and the adjustable grid is brilliant.

[@elguapo1507]

Some people are just great to watch! Lovely to see great ideas, great skills and a great final build! 👍😁

[@carpentak]

thank you!!

[@rayscrafield2106]

I have watched probably 500 youtube videos but your is by far the best. Your creativity and abilities are astounding. I only wish I could have had you for a son or grandson so that I could have learned from you as you grew up. I'm in awe of what you have done here on this video. I have recently gotten interested in laser engraving so that I can sign my woodart. I wanted some way to do taller projects and you have shown me exactly what I needed to see. Thank you so much for your time.

[@carpentak]

Thank you for your valuable comments. Your praise makes me happy. See you again with a good video.

[@Anonymouthful]

What a great DIY project. All you need is a workshop full of tools.

[@claudiorocha2036]

Very, very ingenious! Congratulations.

[@e-train6402]

Ever think about selling those? Would be very profitable in my opinion. I'd buy one!

[@neobaggins3718]

I wouldn't. It's pretty, but it's what's called safety theater. Extraction is insufficient to ensure fumes stay contained in the box and are properly removed through the hose, the clear plexiglass doesn't add any protection from the laser light (the shroud on the machine likely isn't high enough optical density to effectively filter the wavelength the laser is emitting) You're better off with no enclosure and putting the whole machine in an isolated shed, wearing a multigas respirator (about $30) and using a $20 sheet of high optical density acrylic as a portable eye shield for observation. If you don't have a dedicated shed or sealed room where you know people won't end up without PPE, a garage with some powerful shop fans directed to create a negative pressure with doors wide open to allow fumes to vent and don't let anyone enter the garage during use or for about half an hour after use without PPE.

[@carpentak]

I replaced the fan with a bigger one. Then it was much better than before. I chose transparent acrylic to make it easier to film the process. Therefore, color acrylic plates with a blocking function are recommended for those who make them.

[@aaronkosarchuk7833]

you thought of everything! this is an awesome build. Thanks for sharing!

[@zina6581]

What a great idea!!

[@bobolishis7]

Baller, very nice!

[@niqa2000]

Wow wow . Love it. You male me want all those machines you got there to build. Watching this video was so relaxing and fun to watch. . Just love it.

[@apowell389]

That build was bad ass!

[@obamatypebeat]

wow amazing work

[@handlebrand2053]

Well done! I was questioning you until i watched. Very impressed with how you thought it out.

[@onehandcowboy]

First I was thinking (yep I can do that too ;-) ) what is that all about that box? But man that is clever. I think, the moment others stop is where you start to think. Absolutely ingenious :)

[@abelzambranodiaz5452]

asombrado amigo de tu trabajo excelente felicitaciones dios te bendiga

[@15X98]

I will be making one of these, thank you!!

[@pl2996]

ok dang lol. that's some craftsmanship

[@rayscrafield2106]

I just watched this video again. I have to ask, do you ever make a mistake? Your plans, calculations and execution of build always seem to be spot on. Please tell us that you make as many mistakes as the rest of us. Thank you again for your efforts and these fantastic videos.

[@carpentak]

Yes, very often, I make mistakes too. I review my plans sufficiently to avoid mistakes as much as possible, and keep checking them from time to time while working. Thank you for liking my video. See you again with a better video.

[@marc-henridaetwyler9818]

Simply amazing!

[@niltonmanuelpaula4774]

Vraiment génial, Félicitation... j'en ai parcouru des vidéos, et la tienne est incroyable. tu as pensé à tout !!!! Que du bonheur

[@Actio83]

Great job :) love the ok, ok, ok

[@PrinceOfFreshAir]

This is massive. Thanks for sharing!

[@zorand8904]

Super,super!👍

[@adamgeiger4990]

Yep, you should tap it lovingly, Its a fine job.

[@ulricus1]

Sehr gute Kiste !!! Gefällt mir.

[@angelathey957]

You are AMAZING!!!

[@Kloeppeltoni]

Hello, great video and fantastic execution. Where can I get the blue height adjustment that you use in the lower area? Do you maybe have a link for me?

[@carpentak]

a.aliexpress.com/_oDYrtlt Thank you.

[@olegs2607]

Very wonderful work!

[@georgbrunenberg8007]

Amazing, what a great idea and what a great Job!

[@SpikeyBoy25]

Fantastic job. I plan to buy the Atomstack x20 Pro very soon and hope to make something like this, although yours would be hard to match with my limited skills!

[@tech-wurm]

This is a very nice video. The implementation and the purpose is very nice. I use this creation for my project.

[@renatoplacasdesouzacarvalh720]

VC É UM ARTISTA IRMÃO. PARABÉNS FICOU LINDA !

[@1965ace]

Nice!! The first thing you need when you get a laser engraver.

[@taterman320241]

Outstanding enclosure and fine craftsmanship! You gained a new subscriber!!!

[@CantibayPrint]

muy inspirador, gracias.

[@josepastorbuendia4505]

Muy buen trabajo, mis felicitaciones 👏🏻

[@Anatoly_R]

Я потрясен! Великолепная работа!

[@hispanosuizo1601]

La caja ha quedado estupenda, muy buena la forma. Pero la mayoria de la gente en su casa no puede hacerla. Deberia de poner, hecho en taller de carpintería. Aparte de eso, esta genial.

[@mllemelstone]

Bravo, merci pour le partage.

[@manelgt]

¡Impresionante trabajo!!!

[@franciscocarlosrotiroti7066]

Muy Bueno exelente Trabajo un lujo te felicito y gracias por compartir tus ideas

[@DjSpyHp]

Sensacional. Parabéns! Nice Job!

[@mostafagaberahmed6657]

good work

[@3dbruno]

Bravo !! 👏👏👍

[@getwithit90]

So good.

[@MrBiggie280]

I mean this is pretty good!!! This is hands down the best enclosure I've seen. However, I feel you could've used more nails.

[@JamesOcampoPulgarin]

Impresionante trabajo, pero de "HECHO EN CASA" como que no.

[@imadeit3579]

where is the inlet for vent? it is that litle gap on the bottom of the cap? great video by the way, it helped me a lot

[@carpentak]

Yes, there are many small gaps so air can get in. Thank you.

[@ritusharma1092]

Nice one ... Can you make a video about your workshop tools specially the extensions you use.

[@carpentak]

I have no plans yet for a video explaining my workshop. It will be done in a while.

[@jnick67a]

Excellent craftsmanship and beautiful results. I am curious how did you rewire the controller board to separate it from the laser?

[@carpentak]

Nothing special. I drilled a hole and pulled the wire out and reconnected it to the controller. thanks

[@b.a.2671]

Top, aber ohne den Maschinenpark in der Qualität nicht machbar.

[@SAG1028]

What skill.

[@its4michael]

lol...over build much? I see from your shop, you are gloriously set up for overbuilding! 👍

[@ruppoman2008]

Excelente.

[@cajasempaquesecoven1523]

excellent

[@taqmobile]

How do you prevent the spoilboard from being cut/etched when doing actual cuts?

[@carpentak]

I use a honeycomb base plate when cutting.

[@FridgeMagnetFred]

Fantastic

[@rockymtnmovies]

Question, does it really extract all the smoke or does it still fill the room, just not as bad? Also, the wood enclosure made of wood is pretty combustible. Should your laser catch something on fire, your enclosure would be a fire danger.

[@carpentak]

The smoke is very well vented. The fire hazard of lasers is always present, even if it is not a wooden enclosure. I always watch from the side when I work.

[@ACNailedIt]

Very nice build! What kind of clear window material (polycarbonate? lexan? acrylic?) did you use, and is that material good at blocking UV light from exiting the box? Great job!

[@carpentak]

This is clear acrylic. This is a window without UV blocking function. However, there is no problem because the laser head has a protector that blocks UV rays. thank you.

[@Raytenecks]

I bought the official enclosure with mine, and it's been good, but I've always thought I'd design and build a better one. This one does a lot of stuff I didn't even consider! The one thing it doesn't seem to have is a camera mount, though.

[@carpentak]

Yeah I didn't think of a camera mount. I didn't think I needed a camera.

[@Raytenecks]

@@carpentak When I had my camera mounted well, I really got a lot of use out of it for positioning things quickly and easily. But on the new machine, the case bends too easily, so I can't trust the camera.

[@HaidarCrafts]

How does the table saw make the edge grooves so easily?

[@chrischilltv8689]

Very Nice, i need one xD but i am have not the maschin for this all! Were can i buy one?

[@alexcavalcanticosta1585]

Hi how are you!! I'm considering buying a diode laser cutting machine. However, I realized that caution is needed when dealing with MDF. Furthermore, I am wondering whether this precaution should be extended to other materials, especially since, regarding MDF, which is not widely discussed in Brazil, I had to seek information abroad. Although it is a topic that is rarely covered, I was concerned to discover that there is evidence that MDF may be linked to cancer, due to the gases that are produced during the laser cutting process. Unfortunately, I was unable to find information about the gases emitted when burning other materials, such as cardboard. Would you have any knowledge or information about this? Furthermore, I would like to know if there is some kind of exhaust cabin for this equipment, which is capable of filtering and cleaning these gases before they are released into the environment. Look at the answer I already had about this (if you're scared, just don't do it because everything in life causes some kind of harm to your health). Thank you in advance for your help and guidance. thanks ola tudo bem !!estou considerando comprar uma máquina de corte a laser de diodo. No entanto, percebi que é necessário ter cautela ao lidar com o MDF. Além disso, estou pensando se essa precaução deve ser estendida a outros materiais, especialmente porque, sobre o MDF, que não é amplamente discutido no Brasil, precisei buscar informações no exterior. Embora seja um tema pouco abordado, fiquei preocupado ao descobrir que há indícios de que o MDF pode estar relacionado ao câncer, devido aos gases que são produzidos durante o processo de corte a laser. Infelizmente, não consegui encontrar informações sobre os gases emitidos durante a queima de outros materiais, como exemplo também o papelão. Você teria algum conhecimento ou informação sobre isso? Além disso, gostaria de saber se existe alguma espécie de cabine de exaustão para este equipamento, que seja capaz de filtrar e limpar esses gases antes de serem liberados no ambiente. olha a resposta ja tive sobre isso (que se você esta com medo é so não fazer porque tudo na vida faz algum tipo de mal para a saúde). Agradeço desde já pela sua ajuda e orientação. obrigado

[@HurdCrafters]

I just purchased a used Ortur laser engraver and I have searched and searched for ideas on adjustable height engraving and an enclosure. You knocked this one out of the ballpark. Awesome job! Do you have plans available? I usually don’t buy plans but I would be tempted and I’m sure many others would definitely buy!

[@carpentak]

I don't have plans. Instead, I'll show you this. instagram.com/p/ChlqPy1PVIt/?igshid=YmMyMTA2M2Y=

[@cw4608]

Your work is precise! Even your brad nails are perfectly spaced.

[@Morphines]

Well , this escalated quickly. :))) Now I have too much to think about for a "simple" enclosure...

[@claudej55]

Très ingénieux.

[@totoffe6234]

Dommage pas de plan free caisson très bien pensée

[@kalango198]

Fantástico 👌👏👏👏👏

[@292Georg]

💡Besser wäre es gewesen oranges Plexiglas als "Fenster" zu verwenden, statt glasklare Scheiben.

[@azadahmed412]

Hi Carpen TAK_DIY trust u well today. What I like to know is where I can buy a laser. I'm a south African n not sure where to buy a new laser engraving machine thanks for ur help ur video is great 👍

[@carpentak]

hello. There is a link to purchase this laser machine in the description below this video. thank you

[@giovannimartin9576]

Hello bro. That's a very nice enclosure. Could you make a box for Atomstack X20 Pro dimensions?

[@carpentak]

I don't know that model. can't do it

[@safa1586]

Awesome! Btw, what is the balck fan/white pip attachments purpose?

[@carpentak]

This is to send the smoke inside the box to the outdoors.

[@klausrichter5555]

Mit solchen Werkzeugen bestimmt kein Problem

[@alexbrusch126]

Nice Enclosure, Some notes/questions: Are the windows rated for the laser? And do you plan on adding a exhaust/Filtersystem?

[@carpentak]

Thank you. The windows are just plain windows. There are no plans to add an air filter system.

[@jensmeinecke2960]

perfekt👍

[@janjacob2179]

Would It Be Possible To Give A Hint To Where THe Part All Come From As I Search Every Where And Are Not Able To Locate Gas Spring Or The Soft Hinge Use Please Help Box Is Made Just Need To Source THe Hardware

[@carpentak]

I bought them here in Korea. So I can't give you a link. Perhaps you can find it on Amazon or AliExpress.

[@macrumpton]

Looking at this makes me think of how dresser drawers are about the size I need to enclose my laser. I always see people throwing them away on bulk trash day...

[@benpeters8870]

Love this video so much. Wishing to do something similar. Any plans by chance for a reference?

[@carpentak]

I can't make plans, but I'll be seeing detailed pictures of these dimensions on my Instagram soon.

[@j.b.6203]

Hello what is the suction power in cubic meters of your extractor? And where did you get one of this size? Is it powerful enough to extract fumes? A short video on smoke extraction would be very welcome. thank you is very nice work

[@carpentak]

I bought this and chose the 70mm size. Of course, it would be better to use a larger one, but I am satisfied with this. a.aliexpress.com/_mPvWg6C

[@СергейКазанцев-в1ц]

Супер!

[@SD333.]

This is brilliant! What is that lift called? I can't seem to find it anywhere.

[@carpentak]

It's called a scissor lift. It's on Amazon, etc. Thanks.

[@harjotgill5868]

Okk!! That’s too much for me😂