I always install hydrants on a threaded double 90 under ground. It allows it to pivot in any direction without ever putting stress on the pvc/ main . You can literally hit it with a car and be okay
@kevimc7 жыл бұрын
Mr Kapper; you made that look easy and effortless; nice job done
@jayphillips40587 жыл бұрын
Nice job! In my small business, I do quite a few hydrant repair/replace/new jobs, a couple things for the next time around" 1) Good that you built a rock bed, I put in at least a 2'x2' "drainfield" for the weep hole to exit water. It should cover the weep hole with about 6"-12" of rock with maybe that much below, too. Then put a layer of geomat or several of landscaping mat on top to keep dirt from infiltrating the drainfield. Most hydrant failures I see are either the stopper eroded and leaking, or weep holes plugged. 2) As a 'just-in-case" measure, wrap the weep hole in landscape fabric and zip-tie in place. Just a little added insurance to keep it from getting plugged. When replacing or installing with poly line, I do the same with my stainless steel hose clamps. Also with stop/drain valves, along with the necessary drainfield. You'd think those weep holes would always self clean, but they don't. And if enough clay infiltrates, they'll slowly build an impervious layer coming back towards the hole. 3) When planning for exposing the line, if there's any way of knowing the direction of the incoming line, dig in that direction instead of 90° to it. As Rod Parkinson said below, toothed buckets are fairly merciless, and if you are digging with pipes, lines, wires etc. there is less chance of accidental breakage when digging in the direction of lay.
@kapperoutdoors6 жыл бұрын
thanks man, that all sounds like common sense stuff! Wonder why I didn't think of it, lol! Pretty much similar to a french drain.. Well if I have to repair one hopefully I'll remember this.. but I do know that I put alot of gravel down there by the weep hole so hopefully that will be enough to keep the clay out..
@oldpete31537 жыл бұрын
Myself I've always gone with black flexible poly waterline to stay away from glued joints that I've seen let go with pressure spikes or undue movement, as well add a masonry brick or cinder block under the foot of the valve, that will take care of a possible strike from above, just my 2 cents worth.
@bretts16 жыл бұрын
Kapper i used to have a water meter deeper and always under water, hurt my dam ribs every time i had to open and shut. Just torched a pipe in u to go over shut off and tack welded a handle tee. Lmao I thought I really had something till city guy came along with one much lighter that fit. Live and learn. Be great place to clean all the fish!
@jasonpimp357 жыл бұрын
i would have uses a primer also befor using the glue
@eosjoe5657 жыл бұрын
You're good. That hydrant will drain water out the weep hole each time the handle is moved to the closed position.
@oldpete31537 жыл бұрын
Take it from a hoe operator that digging around buried utilities with a tooth bucket is bad business. On a machine that size take a 1/2" steel plate the width of the bucket and about 6" wide and weld it to the teeth. When you dig shallows gradually go deeper and draw the bucket slowly towards yourself in an upward direction, that way if you get too close the smooth edge of the plate will skip over the utility and avert damage. I usually welded to worn teeth then when done remove teeth with plate and go back to your teeth only. Believe me this gets more critical around fiber optic and gas lines.
@MrMharley7 жыл бұрын
Good job Kapper, thanks for all your videos
@kapperoutdoors7 жыл бұрын
Thanks Mike
@gregsandidge56497 жыл бұрын
Question: How much leakage did you find when you tore this out? The reason I ask is that typically you want to add your fittings at the source line first and work out from there. This way you can easily twist your fittings in place. I learned this the hard way.
@kapperoutdoors7 жыл бұрын
Didn't find any leakage, I was shortening it to move to accommodate the new pond. I started on the opposite end because I thought it would be easier to line up the elbow with such a narrow ditch.. Of course that's often how I learn... the hard way :)
@Wakeywhodat7 жыл бұрын
Am I the only one who concretes a 4x4 in to strap the hydrant to? Sometimes torquing on that handle works the PVC loose.
@kapperoutdoors7 жыл бұрын
Well, I took guidance from my excavator buddy who's been putting these things in forever.. is that not what the fence post is for that it is wired to for support? Probably just a more 'economical' way to use the fence post vs concrete...?
@scottfoster2247 жыл бұрын
JOE, No purple cleaner on the pipe before the glue ? Must be new glue Im not awhere of. 40 yr. retired plumber. Keep the vids coming.
@kapperoutdoors7 жыл бұрын
scott foster no, just cleaned it off good. seems to be holding... so far! lol
@kriswaugh45327 жыл бұрын
i thought they got rid of well pits a long time ago ?
@kapperoutdoors7 жыл бұрын
I'm not even sure what you are referring to, 'well pit?' This is not a well pit, its just an external hydrant, that is tied in to city water that services our property.
@kriswaugh45327 жыл бұрын
ohhhh i thought that was a old well where u shut the water off at but they used to put wells inside a " pit " instead of them sticking out above the ground but they got rid of them bc they flooded at least here in ohio
@memyselfandifarmer7 жыл бұрын
must use primer and you are to wait till the glue drys before adding pressure, 24 hours +-
@kapperoutdoors7 жыл бұрын
That glue was fast drying glue, could pressurize up to 200 psi within 2 hours. Thats why I got the fast drying.
@damage68366 жыл бұрын
"Sure hope that ain't a human bone" lmao good thinking
@kapperoutdoors6 жыл бұрын
Lol for sure!
@unclegrandpah84007 жыл бұрын
"Any good day is a good day." ~Jadah
@vipleather5 жыл бұрын
Primmer man. Especially on a charged line my brother.