DIY Project : Simple Controller For Mosfets Rf Amplifier.

[@fertonanful]

My Friend I like so much your KZbin videos!!! I dont undestend your lenguage but I had constructed the Filters and the linear amplifier!!!! Now I am traing to make the control unit!!! Tks From Brazil!!! Py2EPL!!!

[@elizasukiman834]

i have post controler photo special for your Rf Amplifier in my account Facebook...cu good luck🙏

[@dajendra]

Thank OM Eliza for the information

[@elizasukiman834]

sami2... om DaJendra , semoga manfaat . 🙏

[@abbieyaa6233]

nah....ini yg d tunggu2...tks om

[@elizasukiman834]

Trims ... Om Abbiey ... hehehe...penting bnget ini dibuat untuk eksperimen2 lain nya...

[@waskitoadhi183]

cotroller minimal input berapa om,. output usdx bisa.? trims

[@elizasukiman834]

met malam om @waskitoadhi183 , controler ini beda dgn controler pada Video untuk usdx , controler ini tdk membutuhkan input dan output , tapi penggerak rellay ke ground ... 🙏

[@waskitoadhi183]

@@elizasukiman834 terima kasih infonya om...🙏

[@elizasukiman834]

@@waskitoadhi183 ... harus dicoba 😀😀😀

[@novitaangelka3354]

Terima kasih sharing pengalaman...semoga berkah 🙏

[@elizasukiman834]

Terima Kasih ... Semoga manfaat bagi kita semua...khusus nya bagi teman2 yg ingin mengisi aktu luang nya...

[@homebrewguykc1atw268]

Thanks for sharing nice info.

[@elizasukiman834]

hope you enjoy this simple and small project... good luck

[@homebrewguykc1atw268]

@@elizasukiman834 Thanks for sharing info

[@marrakechcity4178]

Hello, can you give me more explanations for making this assembly. And more explanation on the connection with the amplifier board. 73's from CN8GFH (MOROCCO). cordially

[@elizasukiman834]

Thank You for comment in this video , pse see the schematic diagram , the conection with the amplifier board very easy... pse see explanation maybe in another video before... stay healthy keep strongth... 73

[@marrakechcity4178]

Thank you very much. 73

[@turatea1]

Om Eliza, apakah bisa dikontak? saya ingin tau desain PCB nya sederhana tetapi karena belum bisa buat jadinya masih bingung.

[@dadyherman5746]

Terima Kasih sharing kontroler nya... apakah ada lay out PCB nya...😀

[@elizasukiman834]

PCB nya sangat mudah , pertama buat dulu lubang untuk relay, setelah itu dibuat jalur nya dengan spidol lalu di larutkan dgn FeCl3... ferri clorida... jadi deh...

[@haryadifanzuri1664]

Pak Eliza.. Mohon pencerahan nilai resistor (R) attenautor utk 1.pushpull 2.combine 4irf .. 3.combine 8irf..mksh.

[@elizasukiman834]

Selamat malam pa Haryadi Fanzuri ... (R) attenuator yg 1 push pull dalam video...10 ohm/3w

[@haryadifanzuri1664]

Thanks informasi nya pak.. Good luck.. Semoga sehat selalu dan sukses..

[@elizasukiman834]

Trims pa @@haryadifanzuri1664 , kalau yg combiner 4 dan 8 Irf nanti kita buat lagi langsung...sampai betul2 paham...

[@haryadifanzuri1664]

Mksh pak.. Atas informasinya dan pengetahuan nya..

[@fertonanful]

Dear Mr. Sukiman goodmorning!!! Iam Fernando, PY2EPL, and I would like if you send me the image of the PCB of the controler part of you linear amplifier!!! Have a nice sanday!!!! With yor family (QTH)!!! 73’s / 51 my Friend!!!

[@elizasukiman834]

dear Fernando Fertonani , thank you for come to my messenger, I can take a photo of the controller pcb, but this messenger cannot load it, you can see it on my Facebook account. Thank You ... 🙏