DIY QC 4+ 4.0 PD 3.0 Module Test

[@UVOS-z4q]

Dude you are my hero for posting this. Super good info!

[@kapeldiy7482]

Glad to hear that, hope my video helped you !

[@anwin85alon]

Pm me can you to install do solar panel of charger*

[@anwin85alon]

Pm me can you to install do solar panel of charger*

[@bayestraat]

Most PD-USB power supply chips drop the power to 10W per port if multiple ports are used. If you need QC for every port you will need an independent chip per port on the trigger board

[@anwin85alon]

Pm me can you to install do solar panel of charger'

[@giovannipegoraro8740]

Hi, thank you for your video. Could you tell me if I can use this module for a DIY powerbank? Is it bidirectional?

[@kapeldiy7482]

Hi, its not bi-directional, so its not suitable for powerbank as a standalone solution, You will need separate cells charger

[@miniwarrior7]

I saw my Mac switch to 100w charging while using this module with a high power C to C cable. I'm not sure the module could handle 100w constant load but it probably has internal thermal throttling but might be bad to heat shrink wrap it and cover the chips without a heat sync first

[@BeriNaafal]

Input voltage?

[@anwin85alon]

Pm me can you to install do solar panel of charger*

[@ericklein5097]

12.07 plus voltage loss equals 11.5 to the module. So at best the module was using 9V PD.

[@anwin85alon]

Pm me can you to install do solar panel of charger*

[@shan.bikeriders2002]

Absolutely nice video 😍, appreciated 👏🏻👏🏻👏🏻. Can we get 33watts output if we connected 12v?

[@consolechips]

50c is very hot, especially considering it is free air right now. Think how hot it will get if it is concealed inside a vehicle behind the dash or enclosed in some housing without fans.

[@kapeldiy7482]

Indeed it's hot, I recommend using this module in vented environments, or using good heat dissipation. From the other hand my macbook charger is getting really hot when its charging the battery - I believe it can also reach 50c inside or even more

[@lifeai1889]

Actually it's fine It can handle 65w just don't use actual load use dummy load it can even deliver 100w with heatsink

[@rupammondal7110]

In my module the zener diode brakedowned but it works properly Please tell the zener volt rating

[@kslakhani]

Can we use it as reverse charge?

[@pennylane8859]

A great review. I bought some of this from Ali. Thanks a lot. :-) Five thumbs down from hate people, I think!

[@menoahgunzel8146]

If i solder a battery to this circuit, can i chanrge and discharge with this module or is it only one way?

[@4Mi360]

No

[@TheKaukas]

I think I will get this to convert my portable 60w solar panel 18v-15v DC to this

[@RedEyedITguy]

Does fhis have the Ip2538?

[@drumetu71]

Maybe the cable....?

[@electro2606]

When using usb a the module switches to 5 v it said in the institution’s

[@b0tnia]

what can i do for a 12v motorcycle battery to get at least 2 amp???? is sooooooo slow whit my xiaomi reminote 9s, it dont charge just i can get a slow discharge :( helppp

[@stephenshop4946]

Is it hot when used with qc 3.0 or 18w?

[@rheynaldyrama9978]

This is support pps super fast charging samsung ?

[@anwin85alon]

Pm me can you to install do solar panel of charger'

[@서비가-s3g]

is the module working on,,,input DC 20V/4.5A -> output PD Type C laptop ??

[@anwin85alon]

Pm me can you to install do solar panel of charger*

[@darmawanilyass3803]

Can this be used as a replacement for a cellphone charger? assuming daily use

[@aleksinvest7]

Yes, you can use this modul everyday, for charging your phone

[@ibrahimyildirim252]

last week i buyed this module but work only 10 watt when i use more than it is shut down and very hot

[@kapeldiy7482]

So probably you have a defective module, I got a bunch of them, and all charging without issues

[@ibrahimyildirim252]

@@kapeldiy7482 i fixed, little component was broken now no have problem thanks

[@AnasAnsari_7]

@@ibrahimyildirim252 hey my board is behaving like yours can you tell me what you fixed

[@ibrahimyildirim252]

@@AnasAnsari_7 next the +positive terminal have little component you need skip this komponenet or make short. If still not work when shut down check the component temperature same one need be so hot .good luck

[@casaospinatores1009]

19V output charging smartphone with need 5V. This PCB can regulate volts whiting explode dispositives?

[@anwin85alon]

Pm me can you to install do solar panel of charger*

[@ngoclainguyen2479]

Có sạc nhanh cho iphone 15promax không

[@jingy7141]

Do you know what IC it using?

[@Thekiloslaundry]

I have power bank 5v with usb step up 12v. if I use step down 5v 4a can it work?

[@Thekiloslaundry]

sorry the goal is to increase the amperage at the output of the power bank because the power bank only runs on 5v 1a capabilities

[@arielelijah1282]

Hi how much input Voltage and Amperes Needed to function it’s PD charging.

[@kapeldiy7482]

Hi ! It depends - PD can be activated at 9V 12V 15V and 20V on output, but the rule is, that input voltage should be at least 3V higher then expected on output. So If you have a device which runs on 20V PD - you should consider 23V or higher on input

[@menoahgunzel8146]

What does the less indicate? If i may ask?

[@anwin85alon]

Pm me can you to install do solar panel of charger*

[@stanastaud4526]

Could you test it with xiaomi supported QC4 or QC4+?

[@kapeldiy7482]

I will try, need to find some phone with it

[@smoochies5056]

im powering this with 12v but i keeps on and off..do i have defective board?

[@anwin85alon]

Pm me can you to install do solar panel of charger*

[@zrirez3221]

Does it have a galvanic isolation from the PSU?

[@anwin85alon]

Pm me can you to install do solar panel of charger*

[@wahyusetiawan5832]

does this module support fast charging vooc 3.0 oppo/realme?

[@kapeldiy7482]

nope it doesn't, realme, oppo are charged with max 15W using this module

[@wahyusetiawan5832]

@@kapeldiy7482 oke thanks you.

[@Valyoung1973]

Can it charge which support quick charge 3 device

[@kapeldiy7482]

Yes it can, it supports QC from 1.0 to 4+

[@Valyoung1973]

@@kapeldiy7482 okay

[@raylow304]

Hi, what you used as the power input source?

[@kapeldiy7482]

For testing purposes I used Lab power supply, but you can use any DC power supply. Check my other video kzbin.info/www/bejne/rKKxf4R_ps6FsNE&ab_channel=KapelDIY in which I'm building the charger based on old laptop power supply, if you wish to use PD with 20V you have to use 25 volts or above on the input

[@daviontrogdor3026]

Is this good for powerbank

[@kapeldiy7482]

I don't think so, module itself is consuming some power even not charging anything, and it will drain the cells

[@BeriNaafal]

​@@kapeldiy7482 How about adding an on/off button? Like.. only switch-on when using the powerbank. Will there be another problem?

[@rabbippfx]

Can it charge fast on "one plus " phones?

[@kapeldiy7482]

Yes I think so, as long as the phone is comliant with PD standards - probably PD 3.0 or 4.0

[@rabbippfx]

@@kapeldiy7482 " one plus " has a unique charging protocall, 'dash, wrap etc ' . These phones cannot charge fast with any fast charger, they just need the "one plus charger" . That's why I'm asking. It needs to be checked physically with this module. Only then you can get the right answer. If it's possible, please make a physical test ..... Then reach a certain decession. Thanks

[@kapeldiy7482]

@@rabbippfx You are absolutely right ! seems like One plus is out of PD standard ! What you can expect is 15W of charging power according to manufacturer, checked by other people.

[@arainadiaz9219]

Can it boost from 12v to 20vPD?

[@kapeldiy7482]

Nope - the input voltage have to higher then expected PD voltage at the output

[@infiniteoffset]

It can do 20V 5A, but it needs like 24V input. Also it gets really really hot, so some additional cooling might not be bad idea to consider.

[@yoyatech4800]

@@kapeldiy7482 thanks, nice info, so it's like only able to step down the voltage right?

[@kapeldiy7482]

Yes, exactly

[@АлександрЫ-о3з]

на модуль советую подавать 23-24в.

[@SharifulNaim]

that is 45 watt

[@JASONZONE]

wow 😲