DIY Rebar latch

Explore a wide variety of content in our carefully curated KZbin playlist: • Binge-Worthy Content
Find more amazing tips at @TotallyHandyShorts #shorts

[@dirtbikemike7815]

WHY THE CRAPPY TACS EVERYONE DOES IT IT'S POINTLESS

[@parkerr080]

Omg I hate how everyone of these channels weld like that

[@marinecor23]

I didn't even see the welds. I came to bitch about the lack of heat treating and fractures forming in 2 of the bends o.O

[@chiefchirpa6934]

Man shit like that pisses me off aye 😂

[@abdul-rahmanal-surkhi]

اللهم صل وسلم وبارك على سيدنا محمد وعلى آله وصحبه أجمعين 🧡💛🌲🧡

[@Tagerrun]

@@marinecor23 I came to bitch about him not being strong enough to just do it without the heat…

[@joshyingling]

I only saw one time you actually used the heat in the rebar to make it easier to bend, you can do most of this work with the rebar cold

[@PablosProjects]

Yeah exactly

[@calebalt1557]

it’ll crack, I’ve tried bending 90’s with 3/8 and shit’s so brittle it snaps

[@justthetexan9961]

Yeah you can? but why would you when it makes the job a hell of a lot easier?

[@feddy11100]

If you're insistent on using heat why not just use a propane torch while the piece is in the vice. That seems like it would be the fastest way.

[@calebalt1557]

@@feddy11100 oxy acetylene is so much faster, way more heat, way less time to make it cherry red

[@CodPlaent]

I support you Johnny Depp🤣

[@dustyluce4383]

That welded (from pipe to plate) is not fused. Look at it, you see the "lack of fusion", on the bottom toe line of the weld. All that tack, tack, Mig weld BS, is just barely above the strength of silicone calk. Top Notch Product.

[@ralph5450]

Barely?

[@shrxft]

@@ralph5450 yes barely, the welds are shit😂

[@hellfire66683]

Moderate breeze will pop those welds

[@erich7945]

The calk is probably stronger than those welds 🤣

[@hellfire66683]

@@erich7945 never underestimate the power of caulk lol

[@user-hh9pe8br8b]

Да,сложная задумка.Автору класс!!!👍

[@user-nn4fr7ek4k]

Нет мастера обидеть может каждый , хотя изюминка в этом есть легче ворота кувалдой снести чем шпингалет из арматуры сломать .

[@pickle6599]

Да просто манипуляций дофига лишних. Нафиг арматуру нагревать!? Достаточно тисков, ножовки по металлу и сварки, чтобы сделать хороший шпингалет.

[@yarus80]

@@pickle6599 так а какая разница? Он нагревал, вы може не нагревать, если соберётесь повторить, в чём проблема? Я думаю он нагревал исключительно для видео, ибо смотрится по интереснее.

[@lucid_god]

Ah yes I will do it myself with the forge and welder I have in my very room

[@dailycereal6529]

Please for the love of god , lay some continuous welds instead of making a million spots

[@fawkyooo7377]

Lol bruh your (spot welds are trash) I’ve seen some that are decent yours are even penetrating the base metal.

[@awolstew1036]

I was just about to say that about his lul tac welds

[@Fuck9oogleAskMe]

Also they made a big effort to trim the video so that the arc is cut off from the video. Take the time to do a good weld instead 🤷‍♂️

[@__.-.__hi865]

Yeah it looks to be flux core too

[@willt718]

the rails on top of the forge are also his handiwork 👍

[@michaeltumpach1173]

@@awolstew1036 p

[@svt_mike66]

Why can't anyone on this channel weld? Let alone spot weld? 😂

[@MrSnorkeller]

А греть арматуру нахер? Она прекрасно гнется трубой на то она и арматура, чтобы быть пластичной.

[@user-lw7dm4th3l]

Да там вообще куча всего лишнего

[@taraskopyl9993]

Позовите Доктора!)

[@MrNeofelis]

Да это похоже какой-то дурачок. Арматуру всегда на холодную гнули. Он даже греет через ж...

[@user-jj6jd7tn6q]

У арматуры марка стали 25Г2С это обычная катанка там марка стали Ст3сп, а арматуру если нагреть и закалить тогда она хрупкой становится

[@saam1483]

Не проще было щеколду купить готовую, чем это вот всё

[@user-dt9fo9cy8b]

Fun, but that was a totally shity weld, that looks pretty.

[@TCAPChrisHandsome]

DIY? Yeah, let me pull out my torch, welding machine, stack of bricks, and bench vise, that I keep on my bedside table.

[@tzr5864]

Tell me you're not a welder without telling you're not a welder

[@LethalAether]

Dude, Gordon needs that rebar to fight the Combine

[@jmathews470]

That bead placement of the "TACK" weld tho....

[@theexplodedguys264]

Wish your welding be on a tig for that job. AND MAKE IT LOOK SMOOTH PLEASE.

[@yozhikhyper1337]

Кто не в курсе, арматура нужна для изготовления железобетонных конструкций. Остальное от Лукавого.

[@JustAPersonWhoComments]

note to self: practice welding

[@randyherringshaw6325]

To make that latch stronger drill a hole in the plate, chamfer the back so the weld can get good penetration and then weld the catch on the front and back of the plate and grind it flush.... Just a suggestion!

[@RC.3RD864]

I love the work that you do! Who would I ever thought rebar could look so damn nice!

[@nefertaribautista428]

Y

[@kaushaldwivedi9536]

@@nefertaribautista428 0000000000

[@andriesdupreez4170]

Awwwww I know I will use the forge to hear the rebar so it’s easier to bend but I will wait un till it’s cold after I take it out So much waste of a force and propane

[@strongbear01]

La verdad no es necesario calentar la varilla para hacer eso

[@user-sd3ok6kq9v]

Сварщиканец, мимо приварил то

[@user-ys2mq7ff8x]

У нас арматурщики так без горелки каждый день делают . При нагреве сталистая сталь теряет свои сталистые качества . Возьми обычный кругляк нах арматура

[@adamtheredneck4898]

Why do you tack weld your stupid "latch" at least run a bead

[@thesiegeguyjack6679]

So why dont you just make a continuous bead instead of a shit ton of spot welds

[@swagpillage1917]

That guy was face reveal look like a Johnny depp

[@josephemerian9545]

Watch the legs on your welds. They're not even. You're awesome for making these videos keep it up

[@dakotadaulton3148]

You have lost credibility with all welders

[@pitviper-vp2vl]

@@dakotadaulton3148 i second that statemnt

[@justinduarte5739]

$900 in propane to make a$10 latch. Seems legit

[@christopherjones7191]

Thats where the cost savings in the welding gas comes in

[@irishkelly2062]

I'm starting to think you tack weld just to piss folks off.

[@michaelhorner912]

Def some cool stuff you make, but learn to weld. I subscribed

[@edgarromero1482]

Disculpen, eso se puede hacer en frío!!! No hay necesidad de calentar!!! Un herrero con experiencia no necesita realizar mucha maniobra para realizar ese tipo de detalles, en realidad solo necesita un par de ángulos, clavos, una grifa un pedazo de tubo y listo ✅️

[@Thecowboy1950]

Nice door latch

[@collinstheone8814]

Yo yo just a tip round the ends of your bend bars thank me later

[@aleksandrkomissarow8831]

Вы хотя бы шов по красивее делали полуавтоматом

[@user-od2kb1xi6n]

Согласен

[@abbprrodriguez744]

Weld weld weld dont be scared !! No weld spots pls love u brother ❤

[@thefuzzman]

Question: if you're using a blowtorch to heat the rebar, why do you need an oven? Just use the torch to heat the rebar in the vice. 🤔

[@Kballs]

Look at all that undercut!

[@turbogerek]

I think using induction device to heat that would be more easier and saves a lot of energy

[@whatsup8464]

He doesn't want the entire piece red hot...

[@Mongoliantreecow]

"DIY" starts off with industrial sized kiln 🤣

[@afreightdogslife]

I don't know why but I feel like I should go Home Depot and buy some rebar

[@meloman48]

Когда купил много арматуры по акции) что не видео, то с арматурой)

[@vassilip5342]

«Сварщик от Бога»

[@cleaner99]

What is the original rebar's HRC before & after the quenching?

[@michaellance898]

Is it only me that knows this? You can easily bend the rebar without it heating up if it’s not to short.

[@zerotoeverything4348]

idk dude, ill just prolly bend that metal and call it a day i dont have time heating those

[@taraskopyl9993]

Я... Я.... Посрал, там прям.... Прям вываливалось... Вот отсюда! Вы, представляете?!

[@kota7789]

Wth was those tack’s holding? Over half didn’t even bridge the pieces lol

[@taylordavison6849]

You know, you can just buy latches. You don't need the equipment and materials for this gas forge to heat up rebar to make a latch. Latches aren't that expensive and I'd imagine this setup probably costs more than a manufactured latch.

[@user-qu1jg9yu8k]

чел в России не был... армату нагреть ради такой мелочи ахаха

[@user-vb5nx1sr9z]

Греть арматуру что бы согнуть такой диаметр, смешно

[@Pa3HOE_o_pa3HoM]

Пацанчик, мой тебе совет, не занимайся хернёй с этой печкой для пиццы, возьми резак, на крайняк паяльная лампа из дедовского гаража для такой приблуды тоже пойдёт

[@yawmiyat-ismail]

عمل متقون 👍🏻

[@Ridinglawnmower145]

I was chillin with the video until the welding it’s like no one knows how to weld so they just have to do shitty spot weld everywhere

[@eduardomelenchuk6067]

А греть горелкой по месту не судьба?

[@LordSergei]

Задвижка крайне не удобной конструкции

[@Warriormedic68]

The fucking internet's idea of a "diy" is hilarious. If I had this much shit and specialized tooling... I wouldn't need a video to show me how to use it to make a rebar handle.

[@Jrjacobtoler]

Over cut the fawk outta those welds lmaoooo

[@MegaSherman15]

For the love of god……. First, learn how to weld. Running a bead is way more satisfying tbh. Second, you don’t need a furnace in order to bend rebar. Third, it’s not DIY IF YOU NEED A WELDER AND A PROPANE FURNCE THAT NEEDS REFRACTORY BRICKS!

[@blackholescience]

I'm not really one to criticize someone's craftsmanship but this thing is just scrap metal at the end. It's going to fall apart in a matter of days I immagine

[@rogeriomeskita4559]

A solda não fundiu dos dois lados kkkkk

[@trollero5725]

Aggg esa soldadura jajajaj espero aprendas a hacerlo suerte metele ganas

[@paulangel8641]

Assim que eu vi já imaginei que seria isso

[@spire4101]

You can buy a bolt latch at home Depot for 5 bucks save you 3 hours and 25 bucks in materials.

[@yt20yt]

Имея полный комплект оборудования просто приварить кусок гнутой арматуры? Бездарно...

[@user-od2kb1xi6n]

Ты ЧО зато ВИДЕО БЛЕАТЬ

[@user-yz9gn4kl7o]

Я думал выражение «приср*ть» применимо только к электродуговой сварки

[@MrSikeLLa]

Ох и приварил😁

[@anurag4611]

Jitna kharcha or mehnat kiya hai na utne me naya aa jata wo bhi designer

[@mdnormatnor5226]

When thunderstorm coming the rebar is not strike by lightning right.

[@2-_-6]

Ты кроме ручек что нибудь делаешь?😁

[@handsfun3976]

Почему когда я вижу надпись ДиАйВай, мне представляются обосра…ые руки .

[@taraskopyl9993]

Мне представляется мой лечащий Доктор)

[@xMrjamjam]

And with that heat transfer you just ruined the jaws on your vice. Get a leg post vice next time those are designed to hold hot steel and are designed to be hammered

[@user-yd8kp5xq8u]

И не забудьте залить арматуру бетоном!

[@arnoldmmbb]

Where you get the rebars without rust? They always look like crap 😂

[@ralph5450]

You unrust them.

[@LegacyLife_555]

@@ralph5450 wrong..that’s how they come..you have to ask for brand new reo as it tends to sit out side and it only gets a lil rusty it’s not deep rust

[@ralph5450]

@@LegacyLife_555 put in Muriatic Acid.

[@user-sq9cf4bq3w]

Нагадил там полуавтоматом, ужас)

[@NAME_NEMO]

В Челябинске так руками гнут без нагрева

[@simonemariadasilva7708]

Wow all of that for a door thing that i forgot the name...thats why our future is coming way slower lmao 🤣

[@xXNaywoodXx]

Gute Arbeit!!!!

[@lukasjung971]

Nein

[@goinfishin9726]

Latch falls apart first time closing gate lol

[@BruceLee-qj8ve]

Looking good but does it worth it...

[@luismonet6985]

You don't need all that fire to bend the bars..🤪

[@nateyoder9372]

Your welds barely even touch the bottom piece of material

[@melnikovmmvz7775]

Можно было и обычный шпингалет сделать

[@quq_CCCP]

Эмм, зачем? Засов стоит копейки, и почему арматура а не кругляк, тамибез загибания делается сваркой ручка...

[@user-eq5jx8dy8y]

А смысл это все делать? Не проще ли к пруту приварить что надо и все?

[@user-ny2hw9mm4q]

Расскажите этому творцу , что задвижку можно проще сделать 🤣

[@marekpusep6739]

Криативно интересно но эти швы боже эти швы мои глаза!!!!

[@onyxwolfarias6523]

i know u think its diy but it stops being diy when u need 100 dollars worth of tools and three diffrent certifications

[@dirtbikemike7815]

100 buck??? Hell if I could find a propane furnace and a welder that are halfway decent under 2500 bucks I would shit myself

[@onyxwolfarias6523]

@@dirtbikemike7815 butane torches are under 100 and u can use them to make a shit furnace

[@dirtbikemike7815]

@@onyxwolfarias6523 ya that's true

[@TheIMadeThat]

Great, instead of buying a $10 latch I need to buy $300 of tools.

[@dirtbikemike7815]

For a welder that's worth a damn like 750 to few thousand and a furnace for under 600 bucks good luck lma

[@TheFluffyBird]

YOU HAVE A FORGE YET YOU STILL CANT LAY A BEAD? Edit: You could even do this cold, rebar is soft as hell

[@flowsaify]

Rebar can be bend without heating also

[@JohnJohnson-bg2oo]

Why's he using a forge to heat up rebar, and letting it cool down before he bends it?🤣

[@InchFab]

Same reason he's not using a bottle of Mapp gas I stead of whatever the fuck that gigantic contraption is. For the 'gram, bro.

[@Goigigandfriends]

You could have wasted less propane by using a torch 🤦‍♂️

[@user-gq7uv3iq8f]

А че не из 40ки?

[@SosShortsComedy]

Excellent

[@paulandersbullecer3152]

What's the difference between tact weld and the other kinds of weld. I know a little in construction and nothing in welding

[@dirtbikemike7815]

Tac is to hold it in place to make adjustments if needed then depending on the thickness of the metal you lay a continues bead some can be a few inches long a few inches apart or some could be the whole thing jus depends

[@user-xq4rx4rn1l]

Че то много движений

[@32fac23]

Residen Evil welding.

[@leinadalan]

Maybe its the hair plugging all his thinking pixies. Dat weld no good.