DIY Refillable Spray Paint Can

[@un_sir_qui_aime_du_rock]

Now 40 to 50 that's a pressure range I trust more. Nice you also shown some issues the can may have

[@KCartisant1]

Ok ! But how much is the quantity of paint ? And air pressure? .

[@Hugo-o1n4r]

Muy bien, ahora cárgale jabón a esa lata y limpia todo ese desmadre 😂

[@disturbator]

Solder wont stick to valve in my case. It sticks to can perfectly but no way to get it on the brass valve.... I even polished it....

[@bikatchopikachu9550]

You need tin to help you stick the solder

[@disturbator]

​@@bikatchopikachu9550i know. But it still won't stick to the valve even after half tube of tin 🤦‍♂️

[@nguyenhai7853]

Hãy dùng hcl20% pha với chì,thiếc. Dùng hỗn hợp đó chấm vào vùng cần hàn.

[@disturbator]

​@@nguyenhai7853thx i will try

[@simracingsarma]

You should use flux. kind of acid. that will help stick

[@ljulian80]

Solder can hold depend on the kind 5700-14000psi and a sheer strenght of 10000 psi. Plus his had a thread to help. Now lets look at the cyl itself. Well its not a pipe its more of thin tubing which can hold 251 psi. This perfectly safe you must just sale spray paint for a living.

[@sxge2k2]

How much pressure????

[@copyrightcopyright2225]

Max. 3,0 bar.

[@d4rius591]

Thanks for the idea, I can reuse my cvt cleaner using petrol ❤️

[@leegrace9336]

Shaking iron ball inside a tin metal can with liquid petrol ??

[@eshine2001]

Good thing that it’s actually a glass marble instead huh?

[@WillemsMathias]

I did this easier, just get the cap off and fill it with your compressor, i put in 8 bar but it lasts really really short, waste of time in my opninion

[@SayaialahBeliau]

So what about the conclusion😅

[@kidoskids2019]

how many psi sir?

[@nicolashrv]

I think a syringe will work better than a plastic bottle, I have one with a little hose glued to the tip, and later is very easy to wash off by pumping and dumping a solvent for the paint or lacquer used.

[@cheeseninja2002]

As cool an idea it is, I fell it would be easier and get better results if you just attach an airbrush to your compressor.

[@ljulian80]

Well a person doesn't always have a air compressor around or a portable one. Maybe no power where they are painting or no pig tank. No spray brush. There is hundreds of reasons to have spray paint and a refillable spray paint can. By the way you think there is no reason for spray paint in a can to even exist but at 7-10 bucks a can they aren't exactly dropping the prices all while struggling to keep the paint isle stocked.

[@tarunrawatvlogs7592]

can you please send this bottle to me i need it where r you from in india

[@ArvindShukla-ru4dj]

Yes

[@thinkmakerr]

Give me contact number i have one refill type can , my own make like this

[@subhan1641]

he made water gun

[@kidoskids2019]

paint mixing adjustment sir

[@SubMarine1-ew2xo]

❤👌👍

[@edwardhughes352]

Nice job. useful for some projects but wouldnt paint my car with it.

[@MikeB_UK]

Nice idea, however... this is not a good idea because if your solder joint ever lets go, even though your valve is sort of screwed into the thin metal sheet, I am pretty sure that valve will just rip out and come shooting out. It has a good chance to go into your eye if spraying with it. To be safe you would need some sort of internal nut to hold the valve (not really possible) and also an over pressure release valve to prevent the whole thing blowing up if over inflated - hey, just like the commercial refillable ones you can buy.

[@eshine2001]

Why not put the air fill valve on the very bottom of the can?

[@arturotagle5806]

Después de hacer un cochinero levanta todo limpia muy bien. Y mejor dedicate a otra cosa. O pinta con brocha

[@jojomalu]

J'ai juste une question: à quoi sert ce bricolage inutile? Moi, quand le spray de peinture est vide j'en achète un autre; ça coûte pas plus cher que ce bricolage qui ne démontre rien si ce n'est comment faire une soudure à l'étain mal faite...et le résultat est minable. A la fin de la vidéo il utilise un vrai spray pour faire croire que ça fonctionne 🤣

[@elbowroom7993]

Typical French arrogance and cynicism.

[@Hasard19]

tout simplement parce que la peinture en bombe coute beaucoup plus cher au litre que de la peinture en pot, et il y'a de parties du monde dans lesquelles on a pas forcément les moyens non plus. Si tu regardes bien, il utilise bien la bombe de peinture modifiée à la fin

[@jojomalu]

@Hasard19 Et quand la peinture aura séché dans ton pulvériateur, tu pourras le jeter et recommencer ce bricolage inutile

[@18FROSTY]

3:17 mi hermano no sabe soldar con estaño

[@un_sir_qui_aime_du_rock]

Well, it's hard. The tip needs to be fairly clean and some flux before use. Either way he did a good job, I just with maybe a good idea to scrape the surface maybe.

[@ronevongoncalvesdasilvaron516]

Not .eh ha mesma lata de point

[@samirecheverria3231]

La expulsión de la pintura no es muy buena ...

[@rajibsk1004]

50% colour and 50% l P G Gas put into the cylinder by china 1:06 bycycle valve . Easy-to-sending colour and gash by china cycle valve.99 %true.

[@philiprapadas-tn6wc]

Not good enough

[@harmac521]

i think ur using water based paint 😂

[@michaelscott4718]

it probably would have worked mucgh better if you used a higher quality spray paint can like montana or belton mollowtow

[@perumalr9919]

Very very add slow with confuse

[@karuta-z4e]

그냥 돈주고 사자

[@arugowdru8092]

Idea good but take tooo much time and many more mechine needed to help It's not possible to mechine buy all person Apus

[@pagongtagi6124]

bangala want paint, bangala no money buy, bangala recycle. gas tank go boom boom bangala go hospital

[@ljulian80]

Solder can hold depend on the kind 5700-14000psi and a sheer strenght of 10000 psi. Plus his had a thread to help. Now lets look at the cyl itself. Well its not a pipe its more of thin tubing which can hold 251 psi. This perfectly safe you must just sale spray paint for a living.