DIY STEERING WHEEL ARDUINO LEONARDO WITH FORCE FEEDBACK

DIY STEERING WHEEL ARDUINO LEONARDO WITH FORCE FEEDBACK
DIY Materials :
1. PVC Sheet Size.10 x 20 cm Thick 5 mm
2. Pillow Block Bearing Type.KFL-08
3. Bolt + Nut + Ring M4 x 1.5 cm
4. Fully Thread Rod Size.M6 x 20 cm + Ring + Nut
5. DC Motor 12V Merk.NISCA Type.NC5475C
6. Timming Pulley 20 Teeth Bore 6.35 mm
7. Fully Thread Rod Size.M8 x 15 cm
8. Timming Pulley 40 Teeth Bore 8 mm
9. Timing Belt Type.2GT-200
10. Encoder + Sensor Canon Printer IP2770
11. High Current Motor Driver Type.BTS-7960
12. Connector DB15 Female
13. Bolt + Nut + Ring M3 x 1 cm
14. DC Power Connector Size.5.5 mm Female
15. Jumper Cable Arduino
16. Boss Kit Racing Steering Wheel
17. Skeleton Steering Wheel SKT-A SW8914
MORE VIDEO TUTORIALS
ARDUINO CONTROLLER BOX FOR DIY STEERING WHEEL
• ARDUINO CONTROLLER BOX...
DIY PEDALS GAME SIMULATOR
• DIY PEDALS FOR DRIVING...
ASSEMBLY 12V DC POWER SUPPLY FOR DIY STEERING WHEEL
• ASSEMBLY 12V DC POWER ...
DIY H SHIFTER FOR DRIVING SIMULATOR
• DIY H SHIFTER FOR DRIV...
SETTING STEERING WHEEL ARDUINO LEONARDO
• SETTING STEERING WHEEL...
TUTORIAL UPLOAD FIRMWARE TO ARDUINO LEONARDO
• TUTORIAL UPLOAD FIRMWA...
Source :
www.kaskus.co.id/show_post/58...
Credit :
- AI WAVE
- Arduino.cc
- Forum Kaskus

[@muhammadrijalalmahdi5704]

Turotial terlengkap dan terjelas yg ada di youtube.. Mantapp🎉😅

[@edipurwanto25]

Terima kasih, semoga tutorialnya bisa bermanfaat 🙏

[@3xAudio]

cool project

[@edipurwanto25]

Thank you very much

[@jetpatrick6503]

Nice work bro. Does the m8 fit tight on boss kit? How did you plant the m8 in if it is not fit?

[@edipurwanto25]

Thanks bro, in the middle hole of the bosskit I planted M8 nut

[@julianpussetto9739]

amazing, which encoder can I use if I don't have the Canon IP2770?

[@edipurwanto25]

Can, but you have to know the ppr value, vcc+, ground, rx and tx encoder ​​to be used

[@jeytt1]

Hello, I made it as in the pictures, the same firmware. Well, FFB doesn't work for me. Poking with a multimeter, I discovered that the PWM signal (which comes out from pin 10-11) produces a low level of 0.9V. and for this reason, the motor driver supplies only 3-4V to the motor and it hardly turns. I don’t know where to dig anymore, all the components are fully functional.

[@hafeezunban6003]

THANK YOU BROOO!!! ITS NOW WORKKKKK

[@edipurwanto25]

Good work Bro

[@voxalonarlok4934]

any chance i could get the arduino sketch for the encoder? im building a flight simulator and i think these would work nicely

[@edipurwanto25]

Sorry bro I don't have 🙏

[@GT_FREAK]

Great build bro!, How much torque does it have?

[@edipurwanto25]

Thanks bro, the torque is not big because it's for playing ETS2.

[@GT_FREAK]

@@edipurwanto25 Ahh ok thanks

[@edipurwanto25]

@@GT_FREAK You're welcome

[@Ch10ne]

excelente proyecto, pero tengo una duda ¿como conectas el motor a la fuente de la pc?

[@edipurwanto25]

utiliza un conector de alimentación de 3,5 mm

[@bossoy0769]

how much ppr does the printer encoder have, that you use?

[@jokokelono5561]

nice

[@edipurwanto25]

Thanks

[@simulatormania1831]

Kerennn

[@edipurwanto25]

Terima kasih

[@sudiptmandal5607]

bro i am trying to do this but i am using epson 4800 printer encoder but not work just wheel is rotade continusly tell me why?

[@edipurwanto25]

I don't know bro, it could be that the cable path is not correct or the encoder doesn't match 🙏

[@Jesslyohoebesafira]

mantap bang

[@edipurwanto25]

Terima kasih

[@Mert-ot8db]

How did you fix it to the table at the end?

[@edipurwanto25]

For installation on the table using brackets and clamps

[@MrAlejandroexe]

Could you provide us the WheelConfig_0.21 software?

[@viniciusschmidt9050]

can i use the 775dc motor?

[@edipurwanto25]

You can use 775 DC motor

[@arnautandrei5786]

How many degrees does the steering wheel rotate? Is it doable for someone who didn`t use Arduino before but programmed in C#? nice vid

[@edipurwanto25]

900 degress, the program is used for arduino

[@arnautandrei5786]

@@edipurwanto25 no, I mean is it hard to use for someone who programmed before but not in arduino

[@edipurwanto25]

@@arnautandrei5786 I got the program from the source which is written in the description and used for arduino. I don't know if it can be used for anything else.

[@arnautandrei5786]

@@edipurwanto25 no bro, I mean is it hard to learn programing in Arduino?

[@edipurwanto25]

@@arnautandrei5786 Not hard bro, I also just started making this steering wheel a year ago.

[@MrAndrjuha]

Hello,what lenght of Timing Belt Type.2GT-200 you have there? Is it 100 mm?

[@edipurwanto25]

Length 200 mm, width 6 mm

[@MrAndrjuha]

@@edipurwanto25 OK thanks,I following your video and started buy all parts I needed.By the way is 775 dc motor will be OK for this project?As I don't have anything else,I would like to reuse it

[@edipurwanto25]

@Andrejs Gerasimovs You can use 775 DC motor but the bore timing pulley adjusted to the diameter of the 775 DC motor shaft

[@WRCLife_]

@edi purwanto bang coba buat video untuk instalasi kabel nya pusing kalo liat dari foto

[@edipurwanto25]

Lebih mudah belajar lewat gambar wiringnya mas

[@MrMarto]

does it have delay?

[@edipurwanto25]

I use playing ETS2 doesn't delay

[@kentin6348]

hello bro, where can i find the arduino program to make all of this work? Thannnnks :)

[@edipurwanto25]

You can download it here drive.google.com/file/d/1te7JQN99EqIt1OpGkDNpAO1ezo7XkxAt/view?usp=drive_link

[@jorgesernaque2349]

how much did you spend to buy everything?

[@edipurwanto25]

To make the steering wheel, pedals, shifter and arduino controler box estimate of approximately $100

[@funny-mannyvor8jahren583]

Sorry, but can you tell me what exactly z toogle (26:00) is and what it is used for? And is it possible, to use more than two extra buttons? (Maybe you can switch it with the z toogle lever)

[@edipurwanto25]

Z toggle function if the firmware is not read in the wheel config (0.00) then you have to remove the Z toggle, turn the steering wheel left and right. The firmware will change to 0.16. You can add buttons using arduino pins D12, D13, A3, A4 and A5

[@funny-mannyvor8jahren583]

@@edipurwanto25 Thank you for the answer 😁

[@funny-mannyvor8jahren583]

@@edipurwanto25 But I have to change the code in I want to add buttons, right?

[@edipurwanto25]

@@funny-mannyvor8jahren583 You're welcome, yes you have to set it in the wheel config to add buttons

[@funny-mannyvor8jahren583]

Wait, is the firmware supporting that?

[@Potatoleague-ux2zc]

Hi can I use DC motor with encoder instead of canon sensor I don't need to have force feedback too

[@edipurwanto25]

You can use another brand of encoder, but you must know the PPR value. If you don't need force feedback don't use DC motor

[@Potatoleague-ux2zc]

@@edipurwanto25 so if I have DC motor with encoder and I know the ppr what is next I can follow the video and btw your videos are great

[@Potatoleague-ux2zc]

@@edipurwanto25 and I found online the same encoder you have but I don't have the disk you used

[@edipurwanto25]

@@Potatoleague-ux2zc Of course, you must know the PPR value because when making settings in the wheel config, you must enter the PPR value

[@Potatoleague-ux2zc]

@@edipurwanto25 thx

[@musichero945]

can use arduino uno ?

[@edipurwanto25]

Can, but arduino uno does not support force feedback

[@RecehDIY]

om, motor nya kuat kah? bisa bikin pegel tangan gak? lebih kuat mana torque nya ketimbang 775 om?

[@edipurwanto25]

Motornya kuat, kalau mau torque besar bisa pakai 2 motor dan pulley nya juga di ganti yg lebih besar. Saya belum coba pakai 775

[@p1gxz535]

Untuk bts 7960 pakai apa, untuk si sekrup di pvc

[@edipurwanto25]

Saya pakai plat tipis bekas bracket motor printer

[@kennethmanthis2457]

i have a Rotary Encoder instead a Encoder + Sensor of printer how to put it in.

[@edipurwanto25]

Sorry bro I haven't tried using the rotary encoder, maybe the working principle is the same 🙏

[@kennethmanthis2457]

@@edipurwanto25 here's what i am thinking. put a gear on Rotary Encoder and at the end of the thread that is connected to the steering wheel. or adding one more Timming Pulley and belt connected to rotary encoder and the steering wheel. that;s gonna work right?

[@edipurwanto25]

@@kennethmanthis2457 I think the gears or timing pulley are the same and you can try, but the rotary encoder settings may be different in the wheel config. Try looking for tutorials using a rotary encoder.

[@mugendramon8377]

Kalo ada blue print diameter lubang sama jarak antar lubang di pvc sheetnya boleh dong bang di share

[@edipurwanto25]

Kebetulan pas buatnya langsung ukur dan coret di papan PVC jadi tidak ada drawingnya. Saran saya kalau mau buat untuk timing pulley yang ukuran 40 teeth ganti ke ukuran 80 teeth supaya ffb nya lebih besar

[@MrAndrjuha]

Is it ok to use Freenove because that what i have or it only work with Arduino?

[@edipurwanto25]

I don't know bro, it's better if you buy arduino leonardo R3 clone the price is around $6

[@MrAndrjuha]

@@edipurwanto25 Thanks bro!

[@edipurwanto25]

@@MrAndrjuha Okay

[@MrAndrjuha]

@@edipurwanto25 There is no chance download firmware,wheel config file,and .hex file can you help me get them please?

[@edipurwanto25]

@@MrAndrjuha m.kaskus.co.id/show_post/5879c1b9ded770e7728b456c/1326/tutorial-steering-wheel-with-arduino-leonardo

[@MrAndrjuha]

Hi again,I got issue with encoder i have 4 of them but I don't now pinouts of them,can't find online eather. I have 2 Epsons and two hp printers encoders.

[@edipurwanto25]

To make it easy you have to get an encoder + sensor Canon Printer IP2770. Is it not available in your country?

[@MrAndrjuha]

@@edipurwanto25 Unfortunately nope.

[@MrAndrjuha]

Just need to find pinouts for them and wola job done:-D

[@josiah.cameruh]

Can I use a 1000 rpm motor or less, if soo Dow low rpm can I go

[@edipurwanto25]

Yes, can

[@josiah.cameruh]

@@edipurwanto25 what rpm can I do

[@edipurwanto25]

@@josiah.cameruh You don't need to use large rpm but use large torque for force feedback.

[@edipurwanto25]

@@josiah.cameruh The DC motor I use force feedback is sufficient for playing ETS2 but for playing Dirt4 force feedback is lacking. Maybe later I will make it with another DC motor.

[@MrAndrjuha]

At some point i think 8mm rod can be changed to 10mm,but I realise too late already ordered 8mm pulley😄

[@edipurwanto25]

You can also change the timing pulley to 72 teeth for more torque.

[@MrAndrjuha]

Maybe later will do,but first have to finish this:-)

[@rileytedja2475]

halo gan pnya sya calibration eror terus, saya sdh rubah tpi mai blm bisa.

[@edipurwanto25]

Kalau calibration error pilih advance setting -> reset to default

[@mugendramon8377]

Dc motor merk nisca bisa diganti sama yg lain bang?

[@edipurwanto25]

Bisa diganti merek apa aja, sesuaikan spesifikasi yang dibutuhkan

[@lurkingcorsa10]

omm mimin, itu motor dc ny koq dcari gk ketemu. ad alternative laen kgk?

[@edipurwanto25]

shp.ee/e866tkq

[@edipurwanto25]

Bisa juga diganti motor DC lain

[@lurkingcorsa10]

​@@edipurwanto25 kalo pake rs 775..?

[@josiah.cameruh]

What rpm is the motor

[@edipurwanto25]

2700 rpm

[@ernestoutright6265]

Mas ada link pembelian. Baut panjang, pulley dll gak

[@edipurwanto25]

Saya beli online di shopee mas, nanti saya copy linknya

[@mugendramon8377]

Bang itu di tengah as drat 8mm apa namanya yg item item nempel sama kaya ring gitu

[@edipurwanto25]

Itu ring terbuat dari karet tebal untuk menempel rotary Encoder

[@adimulyadi4469]

Udh coba di test buat ngedrift ga bang,?

[@edipurwanto25]

Belum bikin handbrake nya, tapi saya yakin bisa di pake ngedriff 🤭

[@khdevofficialyt8856]

permisi bg mau tanya , knpa punya saya ga berfungsi ffb nya , sya pakai psu pc yg udh sya buang proteksinya . bts7960 udh saya coba ganti² ttp aja , kira² ada dimana ya Salahnya

[@edipurwanto25]

Kalau semua komponen elektronik sudah dipastikan normal kemungkinan ada kesalahan/instalasi jalur kabelnya.

[@muhammadsafarif125]

Mas ada skema pemasangan db15nya?saya gk paham soalnya, pake db15 kelihatan simple buat dipake

[@edipurwanto25]

DB15 ada 15 pin jadi bebas pakai pin mana saja asalkan pin yang dipakai antara DB15 male dan DB15 female sama.

[@muhammadsafarif125]

@@edipurwanto25 jadi untuk kabel penghubung antara db15 itu juga harus sama ya?

[@edipurwanto25]

@@muhammadsafarif125 iya mas harus sama.

[@modssrcreation2222]

Z toggle buat apa ya bang

[@edipurwanto25]

jika firmware terbaca 0.00 di wheel config matikan Z-toggle dan putar stir ke kiri dan kanan sampai terbaca 0.16 lalu hidupkan lagi

[@tristan6509]

Itu bosskit untuk mobil apa bos? Soalnya tiap mobil beda2, takutnya mur nya terlalu longgar kalo salah tipe

[@edipurwanto25]

Buat mobil carry bos

[@tristan6509]

@@edipurwanto25 ok makasih bosqu

[@kisarasiriwardhana4243]

Can I use any printer encorder+sensor How to buy the encorder sensor you used

[@edipurwanto25]

You can find it in the online shop

[@kisarasiriwardhana4243]

Can you give me a link

[@kisarasiriwardhana4243]

Can I use any sensor encorder

[@edipurwanto25]

@@kisarasiriwardhana4243 You can search for recommendations on google

[@edipurwanto25]

@@kisarasiriwardhana4243 can, if you know the pin out.

[@agungwibowo24]

Encordernya pake EPSON bisa ga bang...

[@edipurwanto25]

Saya belum coba pakai encoder lain 🙏 Beli saja yg punya Canon iP2770 di online ada. Saya beli second 2 set murah dan keduanya bisa digunakan.

[@Memescience]

Ijin kak untuk power suply ny pakek punya ap kak

[@edipurwanto25]

Ngerakit sendiri, cek video yang judulnya assembly 12V DC Power Supply. Bahan2 beli di toko online.

[@rickyrifaldy9992]

bang nyari bahan2nya online apa di matrial sama bengkel2?

[@edipurwanto25]

Ada yang online dan ada yang beli ofline

[@p1gxz535]

caa masukin drat ke piloblock gmn?

[@edipurwanto25]

Tinggal dimasukin aja ke lobang bearingnya tapi baut pengunci as di bearing di kendurkan dulu.

[@aldythsatya601]

Ganti pulleynya ke htd yang 3m 72t lebih mantep torsi ffbnya

[@edipurwanto25]

Terima kasih sarannya bang, nanti di coba untuk stir yang satunya.

[@aldythsatya601]

@@edipurwanto25 saya dah coba dengan htd3m 72t untuk as stirnya dan 20t untuk motornya, set ffb 80%, spring 40% dampernya 30% dah kayak bawa truk tanpa power steering. Berat banget ffbnya hihi. Oh iya saya pakai motor dc my1016 psu 24v 20a, kalo abang pake apa?

[@edipurwanto25]

@@aldythsatya601 wah kalau kaya stir tanpa power steering tangan pegel kalau mainnya lama. Hahaha Saya pake motor Nisca NC5475C dan power supply 12V 10 Ampere.

[@hafeezunban6003]

hi bro can it use on forza horizon 4?

[@Anadisty]

Sensor encoder pake punya arduino sensor kaki 5 inputnya 360 apa gimana bang?

[@edipurwanto25]

Sensor dan encodernya pakai punya printer Canon iP2770

[@Anadisty]

@@edipurwanto25 ok bang udah ketemu PPR dari sensor ada yg nyebut 20 lumayan hemat biaya masih riset per part nya gimana

[@saddammurtadho6167]

selain motor merk nisca apalagi om rekomendasi ?

[@edipurwanto25]

Untuk motor bebas mau pakai merk apa saja yg penting 12V DC contoh seperti motor DC 775 dll. Motor 24V DC juga bisa tetapi power supply juga gunakan yang 24V DC

[@saddammurtadho6167]

@@edipurwanto25 ig apa om kalo mau nanya"

[@edipurwanto25]

@@saddammurtadho6167 ada di deskripsi channel

[@ongguen]

Bang, ko pake 2 motor rs 775/795 apakah psu nya jga ditinggikan bang? Misal dari 12v yg awalnya cuma 1 dc, klo pake 2 motor apa psu harus up ke 24v ya bang?

[@edipurwanto25]

Tidak perlu kalau pakai motornya 2 x 12V tetap power supply nya pakai yang 12V

[@ongguen]

Klo untuk ampernya apa ttep 10A atau 20A duakali lipatnya bang?

[@edipurwanto25]

@@ongguen untuk 2 x motor DC 775 menurut saya sudah cukup pakai power supply 10A

[@ongguen]

Brarti 10-15A gpp ya bang? Makasih ilmunya bang, sangat bermanfaat, sukses slalu

[@atengtong3501]

Bang cara nambah tombol untuk steering wheel ny gimana ya apa harus tambah lgi arduino ny?

[@edipurwanto25]

Mau tambah berapa tombol ?

[@atengtong3501]

Kira² 10 tombol

[@edipurwanto25]

@@atengtong3501 kalau nambah sepuluh tombol bisa pakai module joystick PS atau keyboard

[@atengtong3501]

Berarti dual kontroler gpp ya bang 1 pakai arduino satunya pakai joystik gitu bisa ya

[@mysongs6386]

Klo tombol" lain seperti lampu, klakson, sein dll itu bisa ngambil ke arduino gk bang? Makasih🙏

[@edipurwanto25]

Bisa bang

[@Muhammad_rifqi_fauzi]

@@edipurwanto25 bang di jual gak bang

[@edipurwanto25]

@@Muhammad_rifqi_fauzi Tidak untuk di jual hanya digunakan sendiri.

[@Muhammad_rifqi_fauzi]

@@edipurwanto25 pandu cara buat nya bang minta nomer wa atau social media lain nya

[@edipurwanto25]

@@Muhammad_rifqi_fauzi sosmed ada di channel dan cara membuatnya sudah ada videonya

[@hafeezunban6003]

Hi bro my steering wheel is broken at first i thought it was encoder sensor then i replace it nothing happend then i thought it was encoder so i replace it same nothing happend but i remember that my first time try it work but after i install xloader and the forum it broke😢

[@edipurwanto25]

Why is it broken bro? I've been using my steering wheel for over two years and it's fine

[@hafeezunban6003]

@@edipurwanto25 idk after i install xloader and upload the forum its not detect

[@edipurwanto25]

@@hafeezunban6003 Maybe there was an error that you made during the upload process with xloader or indeed your arduino is having a problem. The solution is you have to replace it with a new one

[@hafeezunban6003]

@@edipurwanto25 ok thanks😥

[@CrappyDude]

You already answered the total cost of this project i mean the paddles shifters etcc.. which is 100$ But i want to know the total price of thiss gaming wheel Only the wheel which your building in this particular video.

[@CrappyDude]

Also (Robocraze BTS7960B Bridge Motor Driver) can i use thiss instead of BTS 7960..

[@edipurwanto25]

@@CrappyDude Estimated around $39.5 because I bought a used Canon printer encoder + sensor and dc motor

[@edipurwanto25]

@@CrappyDude I don't know if there is any difference between BTS7960 and BTS7960B

[@CrappyDude]

@@edipurwanto25 its same but can you once check it cuz then i have to order it and also thank you for replying me🔥🤗

[@edipurwanto25]

@@CrappyDude If I look at the specifications and functions are the same

[@ninjagola8471]

Bang habis berapa ya kira kira total bikin setir,pedal sama shifternya. Soalnya mu nyiapin dananya

[@edipurwanto25]

Kurang lebih 1,4 juta bang

[@nico_poriol]

Will this work on forza horizon 4 and 5?

[@edipurwanto25]

I haven't tried it yet but I'm sure it works

[@Automaniac2021]

Bro Any alternative encoder bcoz it's not available here

[@edipurwanto25]

Can use other encoder but you have to know pin out and ppr value.

[@Automaniac2021]

@@edipurwanto25 ok thank you

[@edipurwanto25]

@@Automaniac2021 You're welcome

[@Automaniac2021]

@@edipurwanto25 is there any options to change code

[@edipurwanto25]

@@Automaniac2021 What code do you want to change?

[@tbilal11201]

ini bosskit nya punya mana bang? ada link pembelian?

[@edipurwanto25]

Bosskit untuk Suzuki carry

[@_Itachi_240_]

is it possible in arduino uno

[@edipurwanto25]

Arduino Uno does not support force feedback

[@_Itachi_240_]

@@edipurwanto25 oh ok Thanks for the reply

[@edipurwanto25]

@@_Itachi_240_ You're welcome

[@_Itachi_240_]

If I don't need Force feedback can I use Arduino uno

[@edipurwanto25]

@@_Itachi_240_ Can Bro

[@ayrtonmarin6778]

I want to build one with a Nema 34 8nm or 12nm stepper motor, what do you say?

[@edipurwanto25]

I have stepper motor but haven't tried it yet.

[@wahidkurniawan1174]

Review pedalnya om

[@edipurwanto25]

Kalau ada waktu nanti dibuatkan juga videonya, masih sibuk kerja dan bisa buat video ketika libur 🙏

[@wahidkurniawan1174]

@@edipurwanto25 sip om ditunggu 👌

[@05iketutsagotrawangsa59]

Dinamo belinya di mana bang?

[@edipurwanto25]

Di toko online shopee

[@hafeezunban6003]

Can it use on ps5

[@edipurwanto25]

Sorry I don't know and I don't have PS5 🙏

[@hafeezunban6003]

@@edipurwanto25 ooh ok btw im 80% complete

[@edipurwanto25]

@@hafeezunban6003 Good job bro 👍

[@zulelectronic]

Untuk pa tujuan sensor tu mas?

[@edipurwanto25]

Untuk membaca timing disk dan ketika stir di putar agar bisa kembali ke posisi semula ( center )

[@nge-gamebae7940]

Halo pak, setting encordeenya gimana ya??

[@edipurwanto25]

Cara settingnya ada di channel yang judulnya setting steering wheel arduino

[@groovy8829]

Can we use Table Fan motor ac

[@edipurwanto25]

Can't, because the motor driver used is DC

[@groovy8829]

@@edipurwanto25 okay thank you

[@groovy8829]

And one thing,can we use another printer encoder

[@edipurwanto25]

@@groovy8829 You're welcome

[@edipurwanto25]

@@groovy8829 It's possible if you know the pinout and ppr value

[@anggasetiawan7988]

itu pake stir yg brpa inci om

[@edipurwanto25]

Diameter 320mm ( sekitar 12,5 inch )

[@zokey2222]

Csá tesó más játékokhoz is használható vagy csak ets2? Can it be used for other games or just ets2?

[@edipurwanto25]

Most próbáltam ki ETS 2-n és Dirt 4-en a források szerint más játékokhoz is használható

[@toastedbagel9095]

Is it any better than G25 or G27? Also, how much did it cost in total (USD)?

[@edipurwanto25]

I haven't tried the G25 or G27 yet and I made steering wheel to be able to play the simulator at low cost ( the estimated cost is around $100 )

[@toastedbagel9095]

@@edipurwanto25 Does that come with the pedals or $100 for the wheel only? Is it noisy? Sorry for many questions

[@edipurwanto25]

@@toastedbagel9095 for all ( steering wheel, pedals and shifter ) not noisy

[@toastedbagel9095]

@@edipurwanto25 okay thanks for answering my question!

[@edipurwanto25]

@@toastedbagel9095 You're welcome

[@p1gxz535]

bang potong pvc pakai apa

[@edipurwanto25]

Potong manual pakai gergaji besi

[@p1gxz535]

@@edipurwanto25 ada link pembelian mas?

[@edipurwanto25]

@@p1gxz535 shopee.co.id/product/42165804/6279352184?smtt=0.154633846-1651488911.9

[@mugendramon8377]

Total budget abis brp bang buat steering wheelnya?

[@edipurwanto25]

Komplit dengan pedal, shifter, box control arduino dan power supply kurang lebih 1,5 juta

[@fajaroutbox847]

Mas, saya kemaren rakit stering whell pakai puly mesin jahit, dinamo RS 795 PSU pakai bekas PC 12v, -+14A, diconfig stir sudah sukses, dimainkan di ETS2 berat banget lalu pas belok itu lawan arus putaran dinamo ko bisa short ke PSU nya, kira2 knapa ya? & juga kabel PSU ke motor driver nya panas

[@edipurwanto25]

Saran saya setingan spring, dumper dan lain2 jangan terlalu besar karena motor akan kerja keras dan panas sehingga bisa mengakibatkan short. Saya sudah 2 tahun pakai steering DIY belum pernah mengalami short cuma motor saja yang terasa panas makanya di video DIY yang lain saya tambah cooling fan biar motor tidak terlalu panas.

[@fajaroutbox847]

Ok trimakasih mas jawabannya 👍

[@fajaroutbox847]

Oh ya mas klo pakai PSU bekas PS3 12v 32A kuat ga?

[@edipurwanto25]

@@fajaroutbox847 Sesuaikan dengan motornya mas, saya pakai motor nisca NC5475B dan pakai power supply 12V 10 Ampere sampai sekarang aman tidak ada masalah.

[@fajaroutbox847]

Terlalu besar ga puley nya?

[@holdenlasepy8029]

Bro ada tutorial kalau mau nambah bbrp tombol pakai rangkaian ini?

[@edipurwanto25]

Mau menambah berapa banyak tombol bro ?

[@holdenlasepy8029]

@@edipurwanto25 misal lebih dr 2 tombol, hrus nambah controller kah?

[@edipurwanto25]

@@holdenlasepy8029 saya menggunakan pin di arduino D12, D13, A3, A4 dan A5 untuk tombol dan pin lainnya untuk stir, shifter dan pedal.

[@agungwibowo24]

Power suplay berapa ampere bos

[@edipurwanto25]

Saya pakai yg 10 Ampere bos

[@agungwibowo24]

Saya pake 5a kok ga kerasa ya FFB nya.. tp motor pake rs 775

[@edipurwanto25]

@@agungwibowo24 saya juga ada satu lagi yg pakai motor bekas printer dan memang FBB nya kurang berasa.

[@agungwibowo24]

Saran pake motor apa bang

[@edipurwanto25]

@@agungwibowo24 yg di video saya pakai merk Nisca Type.NC5475C lumayan berasa buat main ETS2. Coba otw ke forum Kaskus bang mungkin di sana ada rekomendasi motor yg bagus.

[@psatirhandal6927]

Masang kabel dari dinamo sama Colokan DC, ke motor drivernya kebalik gpp kan bang? Takut konslet 😂

[@edipurwanto25]

Kalau yang konektor DC ke motor driver jangan kebalik mas takutnya motor drivernya rusak 😀

[@dennywahyu9233]

Bang , disini arduino , di controller box juga arduino , berarti btuh 2 bang arduinonya

[@edipurwanto25]

Cuma satu arduino yg di controller box, kalau yg di stir cuma motor driver.

[@dennywahyu9233]

Yg di belakang motor driver , ada tanda merah & biru itu apanya bang ???

[@edipurwanto25]

@@dennywahyu9233 Itu terminal kabel untuk paralel tegangan 5V dan ground.

[@dennywahyu9233]

Memang namanya terminal kabel gitu ya bang ??

[@edipurwanto25]

@@dennywahyu9233 Terminal Paralel Warna 2 Input 6 Output SPL62 Itu namanya cari di shopee

[@rakaneko4229]

Sambungin nya pake usb 3.0 apa 2.0 bang?

[@edipurwanto25]

USB 2.0 bang

[@rakaneko4229]

@@edipurwanto25 ok makasih bang

[@edipurwanto25]

@@rakaneko4229 sama-sama bang

[@zilcard959]

Power supplynya pakai apa om?

[@edipurwanto25]

Power supply 12V 10A, beli di shopee

[@zilcard959]

@@edipurwanto25 ok om, ceritanya aku mau ambil motor rs775 dua buah, apa power supplynya masih cukup

[@edipurwanto25]

@@zilcard959 cukup mas

[@zilcard959]

@@edipurwanto25 kalau masalah kabel, kabel awg berapa om? Lalu kalau mau pakai motor my6812 kan 100 watt tuh, nah harus pakai psu apa?

[@Thegreatdrive41]

bang kira2 habis berapa ya

[@edipurwanto25]

Untuk semua ( stir, pedal, shifter ) biaya nya kurang lebih 1 - 1,5 JT bang. Kalau menggunakan kayu dan part2 bekas bisa lebih murah ( di bawah 1 juta )

[@agung8374]

Mas punya saya ffb nya nggk berfungsi, terus di wheel config wheel error

[@edipurwanto25]

Pemasangan kabelnya sudah sesuai belum mas coba di cek soalnya butuh ketelitian dalam pemasangan.

[@edipurwanto25]

Kalau pemasangan sudah sesuai pasti bisa berfungsi, lihat link di deskripsi ( forum Kaskus ) ikuti petunjuknya.

[@agung8374]

Mas punya no wa atau FB, biar saya tanya2 bisa lebih jelas lagi

[@edipurwanto25]

@@agung8374 chat di FB atau IG mas

[@agung8374]

@@edipurwanto25 ini udah saya susun ulang kabel nya tapi malah stirnya muter terus

[@suharyono1236]

Pake dinamo beda bisa

[@edipurwanto25]

Bisa mas

[@suharyono1236]

@@edipurwanto25 dinamo printer bisa

[@edipurwanto25]

@@suharyono1236 stir saya yang satu lagi juga pakai 2 dinamo bekas printer.

[@egofficial581]

Bro kalo mau pesen bsa ga, biaya brpa?

[@edipurwanto25]

Maaf bro saya tidak menjual 🙏

[@gindiyanti4976]

Total berapa

[@edipurwanto25]

Total biaya untuk semuanya ( stir, pedal & shifter ) kurang lebih 1 - 1,5jt

[@anggitarwianata3827]

step upload program nya ke arduino Leonardo, kemana bang ? kok di skip

[@edipurwanto25]

Cek di deskripsi / beranda yang judulnya tutorial upload firmware ke arduino leonardo

[@daffaatalla6054]

ini berapa degree ya mas? kalo boleh tau apa sih yang mempengaruhi ratio putarannya? terima kasih

[@edipurwanto25]

Untuk degree bisa di setting sesuai keinginan kalau main ETS setting 900 degree kalau game racing setting 180 degree atau sesuaikan dengan keinginan. Yang mempengaruhi ratio putaran adalah gear atau pulley yang digunakan.

[@daffaatalla6054]

@@edipurwanto25 kalau pulley yg dipakai mas edi apakah 900degree ya mas?

[@edipurwanto25]

@@daffaatalla6054 kalau degree itu bisa di setting di wheel confiq mas tapi kalau ratio pulley pengaruhnya ke torsi force feedback.

[@daffaatalla6054]

@@edipurwanto25 oke mas edi. terima kasih banyak

[@edipurwanto25]

@@daffaatalla6054 sama-sama mas

[@king_james_official]

hi, what are the 3 potentiometers used for? 30:01

[@edipurwanto25]

The 3 potentiometers for the accelerator, brake and clutch pedals

[@king_james_official]

@@edipurwanto25 thanks! where can i find the software? i think it's not available anymore. could you host it on mediafire maybe?

[@edipurwanto25]

@@king_james_official look in the comments kzbin.info/www/bejne/gXfOlZaZd9Gbrc0

[@hafeezunban6003]

Hi bro can you give me the most latest firmware thanks

[@edipurwanto25]

I only have this drive.google.com/file/d/1te7JQN99EqIt1OpGkDNpAO1ezo7XkxAt/view

[@hafeezunban6003]

@@edipurwanto25 ok thanks

[@edipurwanto25]

@@hafeezunban6003 You're welcome

[@rayhanfadilah171]

Om itu dinamonya kuat ga,pakai stir asli,,bukan stir racing

[@edipurwanto25]

Kuat mas

[@rayhanfadilah171]

Siap makasih infonya om,tapi kalau mau tambah jadi 2 motornya bisa ya

[@edipurwanto25]

@@rayhanfadilah171 bisa malah lebih bagus pakai dua motor

[@rayhanfadilah171]

@@edipurwanto25 ada ig,atau apa gitu om biar nanti ngobrolnya enak

[@edipurwanto25]

@@rayhanfadilah171 ada di channel saya

[@p1gxz535]

bosskit nya suzuki apa gan?

[@edipurwanto25]

Suzuki carry gan

[@p1gxz535]

@@edipurwanto25 pnya sya jga gtu gan, tpi kok bolongan lebih besar dri 8mm

[@edipurwanto25]

@@p1gxz535 lihat di video saya mas di lobang bosskitnya saya tanam mur M8

[@p1gxz535]

@@edipurwanto25 mksih

[@edipurwanto25]

@@p1gxz535 sama-sama

[@ytbpremium9136]

Dijual gan steering wheelnya?

[@edipurwanto25]

Tidak gan hanya digunakan sendiri.

[@bangkurosok7641]

Download ai wavenya dimana ya om linknya pada mati semua 🙏🙏🙏

[@edipurwanto25]

Lihat di kolom komentar kzbin.info/www/bejne/gXfOlZaZd9Gbrc0

[@bangkurosok7641]

@@edipurwanto25 makasih om Edi 🙏🙏🙏

[@edipurwanto25]

@@bangkurosok7641 sama - sama

[@Asalvlog22]

Kunci L ukuran berapa itu bang?

[@edipurwanto25]

Yang mananya bang ?

[@Asalvlog22]

Ya itu di dalam video ada kunci L panjang , yang ngencengin drat asnya, di bagian bearing ada bau kecil itu

[@p1gxz535]

Cable db15 gimana gan?

[@edipurwanto25]

Maksudnya gimana apanya ?

[@p1gxz535]

@@edipurwanto25 pemasangan cable db15 gimana

[@edipurwanto25]

@@p1gxz535 DB15 ada 15 pin jadi bebas pakai pin mana saja asalkan pin yang digunakan antara male dan female harus sama

[@p1gxz535]

jadi kalau solder 8/15 pin msi bsa?

[@edipurwanto25]

@@p1gxz535 pakai 8 kabel bisa kan maximal 15 kabel

[@hafeezunban6003]

Hi bro i have buy 2 arduino at first it was detect as keyboard then i refund second i buy it was same thing happened and it was tested the seller say the refund arduino was not broken please help me

[@edipurwanto25]

Why is it like that bro, it should be detected as arduino. I have tried on 2 PCs and 1 laptop, all are detected as arduino.

[@hafeezunban6003]

​@@edipurwanto25 bro i have upload the firmware using xloader and it detect as other device but then when i test on wheel confiq its not moving the steering

[@hafeezunban6003]

​@@edipurwanto25 i have complete the steering wheel 99% just 1% is the problem😭 please help me bro

[@edipurwanto25]

@@hafeezunban6003 Have you installed arduino drivers? You have to make the device detect as arduino for the steering wheel to work.

[@hafeezunban6003]

​@@edipurwanto25 yes done

[@shilviayufitrya7259]

Dijual gk?

[@edipurwanto25]

Tidak di jual 🙏