DIY Steering Wheel Pedals H-Shifter - Arduino | Part 1

[@panzer_5724]

finally a tutorial that will actually show a full step by step tutorial

[@MrAlejandroexe]

It has the software for arduino leonardo, xplorer and firmwares

[@АлександрФарш]

thanks a lot.I almost cried with happiness when I did it.

[@SanaKhan-cg6wi]

Hey, did u try it?....Did it work?...I'm planning on doing this as my final sem project since I wanted one for my pc but I couldn't afford it

[@FacuPadi-ms]

does the forced feedback work? is it powered by the game or it just does some opposite weight?

[@dimitrijekrstic7567]

There is no servo in the schematic in the video, so I expect no ffb

[@prince-of-saiyan]

Can we use any other sensor please help🙏

[@prince-of-saiyan]

How was your experience was it good or bad , I m also going to try it , is it worth the efforts

[@stolenusername1627]

Nice! At last, I will be able to craft my own pc steering wheel! All I need are common household and electronic items, found in any store, like an arduino, switches, wires and a *CANON IP2770 PRINTER ENCODER*

[@nicob3046]

Pretty much any encoder will work

[@klazzera]

i don't have a canon ip2770 printer at hand so i'll use my Panasonic Minas A4 Industrial AC servo laying around for both the motor and encoder, pretty handy!

[@MrAlejandroexe]

It has the software for arduino leonardo, xplorer and firmwares ?

[@akshaychavhan9551]

Can you make a seperate video on programming with voice guidance

[@prince-of-saiyan]

Have you tried it ???

[@ZeriKsSplashe]

When i connect encoder to arduino, axis x dont work anyway :( Encoder from logitech driving force gt

[@norbertsvab]

Hello you founded the solution ? Because i have the same problem ... but if i use EMC utility the encoder is forking... but for me this firmware is better than emc firmware

[@b03-capuzmarcgeff43]

@@norbertsvab same

[@krishnakarma6166]

@@norbertsvab do you have emc pro with emc firmware?

[@veerpatil4476]

It is best then g29 G29 =30000rs Our home made streeing in = 5000rs Thank you sir love from India ❤️❤️😭😭❤️❤️

[@AgaYuditraStudio]

no problem bro

[@veerpatil4476]

@@AgaYuditraStudio thanks for your reply

[@CosyGnomeStudios]

Brilliant work man!! Well done!!

[@سروشرستگارمهر]

Hello and thanks for your educational post. The question that comes up here firstly is with what system these devices work. It's either a computer or computer, and what the system has. Secondly, the cost of the device is less than the device ready and made by the company.

[@zzzzzz-du9et]

Sir can we attached Logitech steering wheel with Arduino

[@AgaYuditraStudio]

Yes you can

[@beastold1320]

@@AgaYuditraStudio how

[@jzleong]

@@beastold1320 i think connect buttons cable to Arduino

[@JoshuaBrown-j1y]

This is such a great tutorial. Thank you for sharing! Can You Please list new url's for all of the software, yours are not working?

[@cgcm5864]

Can use this tutorial in Arduino uno without the ffb?

[@vanrazvanper1443]

Yes

[@animations2430]

Please I cannot download ai wave...... which website should I use

[@jotmusic1]

Hlo sir, I can use Arduino Uno

[@munzee7597]

You can't it's to tiny

[@bobi_lopataru]

I just need the clutch pedal and the limit switches, can I only make those and it will still work?

[@rushikeshtiwade3363]

How to make a steering wheel for PS

[@martinkahak2025]

I can connect another potentiometer to the hand brake?

[@restorationpassion3920]

would you link me the encoder and timing diisk printer

[@dawid643]

@ShivKiran This Work?

[@vegas6987]

Hi, I wanna be to make a h-shifter with multiplication switcher, tell me please. Can I to connect a third contact to digital pin? If there are using only 2 contacts.

[@josueherrera8547]

Alquien me puede ayudar? Me sale calibrating error, a que se debe?

[@Zraner]

Lo arreglaste?

[@pablofiorio1547]

me pasa lo mismo y no se como solucionarlo

[@josueherrera8547]

No, abandone el proyecto y me compre un LOGITECH G29. Es broma, aunque estuve apunto de hacerlo. Ni recuerdo como lo hice funcionar, no usen ese encodificador de impresora es fragil, aunque pude realizar pruebas de manejo en Need For Speed Most Wanted y si funciona, aunque lo hice de manera muy rustica ya que tenia que acelerar con el teclado. El proyecto es posible? Claro, pero seria bueno que hagan una lista con los materiales a utilizar e investiguen bien que programa utilizaran.

[@josueherrera8547]

@NICHOLAS KUCZEK If you are using a printer encoder my experience may help you. At the time, do the same, as the diagram indicates, just connect the printer encondifier and the toggle switch to the arduino, it still did not connect the pedals or the gearbox. At the beginning it did not work either, I realized that this connection diagram of the printer encoder is not always correct for all encoders (I mean where it says printer encoder, and yellow, red, blue and black lines come out of it). I recommend that you test the connections, maybe the blue line, in your encoder it is the red line and so on with all the lines. I hope I have explained myself well, in any case you can consult me.

[@saquenmedelatinoamerica1203]

@@josueherrera8547 hola bro, de casualidad aun conservas el codigo? parece que se cayo la pagina xD

[@CaptainLifend]

Does normal encoder work too

[@sridharanmurugesan2100]

Can u tell me step by step procedure with pictures... I m interested in making steering wheel , shifter with hand brakes and pedal Can you send me through mail... I need complete notes for it...plse can u make it for me and send it...

[@AgaYuditraStudio]

you can see on kaskus kask.us/hU9eJ for step by step pictures

[@louisuchihatm2556]

Uhhhm...this is a new world to me. I have been learning some one two things about embedded engineering and IoT. I wanted to make a steering wheel, pedals and a gear shifter. Saw this and I feel like am just lost. I feel like I have been reading the wrong books. Can someone help me get there. What resources do you recommend. I am doing Bsc. in Mechanical Engineering so I've dealt with tough concepts.

[@AgaYuditraStudio]

Good luck bro. Stay safe.

[@grzegorzsram2131]

Kto z polski a i kto w 2018

[@patrykoczkowski9151]

Ja

[@tea3k1]

znasz sie na tym ?

[@gamersialke4433]

Ktoś wie pod jaką nazwą w polsce szukać encodera?

[@KOkos0422]

impulsator albo enkoder

[@fadlakamal8537]

Izin bertanya mas. Saya kan juga ada nii yg diy steering wheel, shifter, pedal arduino. Tetapi yg terdetek dan bisa digunakan hanya pedal&shifter, steer tidak bisa digerakan kiri kanan. Z toggle sudah benar, kabel yg ke tx, rx, 5v, dan ground sudah benar juga namun tetap tidak terdetek steernya gerak di wheel config. Kali aja mas tau ini kenapa. Terimakasih 🙏

[@vegas6987]

Why you connected encoder to digital pins? It must be on analog pins?

[@mustafaguder]

hi bro, i bought rotary encoder 1000PR from aliexpress, and connected. Wheel COnfig say is " wheel ready" but no response.. what is a problem?

[@CaptainLifend]

Does normal encoder work too?

[@krishnakarma6166]

Bro my wheel give spring in one direction which is right to provide ffb on left and If I turn spring low then it give ffb to right and almost no ffb or less ffb to left how to fix this?

[@keymactime517]

Does i really need the extra buttons??? Because i dont find a printer encoder and i need two optical encoders

[@dhifandar8669]

Printer encoder yang kaya gimana ya bang? Trus printer encoder yang rekomen apa yaaa?

[@matei_dragos850]

why it dont connect? At stats is "calibraton error" and encoder doesnt work? What can I do?

[@uaydn_]

@NICHOLAS KUCZEK use Emc Firmware

[@ehsanbeheshti9990]

Hey man You are AMAZING ... Thank you...

[@AgaYuditraStudio]

You're welcome!

[@VTProto]

hello can i use a E6B2 CWZ6C OMRON Rotary Encoder?? if yes where can i connect the wires??

[@razan800]

Hello, i have a problem with my gearbox, it won't see my 7-th gear whatever i do, i try to re-solder everything, but still no 7-th gear( Micro-switcht is working.

[@jamesvirtudazo]

i have a problem... the wheel config isn't detecting any movement from the encoder... i'm using an encoder from hp... with another sort of sensor so i'm not sure where to connect....... the pedals go crazy in the wheel config but are detectable. the only thing working properly is the shifter.... please help...

[@hackingisnotevil2703]

Hey! Nice project but i have a problem. When I connect the encoder to the arduino, install the hex file into the bootloader and open the program, it doesnt show me any movement. Any help?

[@ottongato1]

hey, did u solve the problem? i am having the same issue.

[@K0tyura]

How to connect more buttons to analog input a3-a5? The steering wheel has 8 buttons; there are no free pin on the Arduino digital pin.

[@AudioTherapy0]

Please Help! I bought A64B Photoelectric Encoder and I wired it up correctly. But wheel spinning is not detected. A red triangle thing in Wheel config software only moves little bit when I insert disk in that encoder. What is the problem? please help! I built steering wheel and H-shifter and now I can't get steering wheel working

[@AudioTherapy0]

I got it working! Looks like this encoder was defective and I was able to get it working by disassembing it and re-positioning IR led without its construction (the plastick thing). Now it works perfect!

[@cafepalito2702]

Can I use 2 arduinos in a I2C protocol? Or can I use 2 potenciometros to recognize as button? In this case. I'd to use the same system used at G27 Wheels, depending of potentiometer value, we can set as buttons.

[@Lufisafer]

kkkk Br né? potencioMETROs

[@ImprevisibleDev]

where can i bought an encoder and timing disk printer ?

[@olinos4461]

Hi. I cannot get it to work with WRC 4,5 and 7. Wheel is recognized as a joystick not wheel. so game has a very very big dead zone that cannot be removed. I tryed setting wheel at 180 deg put deadzone is still big

[@shehreyarafzaal2814]

i know its has been much time since this video but i wanted to ask is there anything i can replace the encoder+timing disk printer please answer soon also really appreciate the efforts

[@郭溢屹]

Hello, I can't buy this grating. I want to use encoder instead. How can I connect? 您好，我买不到这个光栅了。我想用编码器代替，请问要怎么接线啊？

How can I use the potentiometer as a steering wheel? I try but It doesn't spin properly.

[@kuroyami6289]

I was planning on using hall effect sensor for steering position, where should I connect the wire for that?

[@szymonpl1000]

Why extra buttons and h-shifter don't work? I connect and setup everythink like on the video

[@barathkuber1141]

Bro...I did everything...buy during testing the TX RX port is not working...both tax RX led blinks and even encoder output is showing...but what will be the problem...?

[@nazmannuzol7432]

in your last video, you put capasitors to your potentiometer for the pedals. why is that? and how to wire it? do you have the wiring schematics?

[@AgaYuditraStudio]

Capasitor use for noise filter. 3 pin potensio (5v) (analog pin) (gnd) = wiring (+) (gnd join with +) (gnd) = capasitor

[@nazmannuzol7432]

can you sketch it out real quick in ms paint? i still cant imagine how the wiring is done haha

[@benjaminkehoe2812]

Did you use a resistor with the printer encoder

[@bertbdg]

gan, encoder ane kenapa cuma ngedetect satu arah ya? si setirnya kalo di gerakin ke kiri segitiga merahnya ke kiri, tapi kalo setirnya di gerakin ke kanan, segitiga merahnya terus ke kiri. ane pake encoder canon ip2770, wiringnya uda persis sama videonya. help gan

[@tacnicalbhai1442]

Ai wave 2016 wheel config software download problem

[@vanrazvanper1443]

Hey. I can't upload the the ffbwheel.0.16.Leonardo.. Upload failed.. Help

[@prica25]

Probably you already fixed your problem, but for everyone with same problem, can just use ArduinoSketchUploader from christophediericx, that's gone work.

[@vanrazvanper1443]

@@prica25 thanks . i fix it with the EMC .. Appriciate

[@m4th1s8]

I can’t find a ip2770 encoder. Will another one do the trick? Wich one?

[@ernestoutright6265]

Bg mau nanya. Gimana kalau gear nya pakai model sequential. Berarti cuma pakai 2 switch ya. Dengan rangkaian pemasangan sama dengan di video

[@bagira368]

Does this simulator kit works for any car game? Even most wanted...???🤔🤔

[@longphanphamviet5192]

Can you show me how to calibrate the Analog (Y and Z axil?)

[@thijnhulshof8688]

Hello! Awesome vid, but I have a problem with downloading the software from force-dynamics. Everytime I open the link it says that the page was not found. Could you help me?

[@maximiliandegen7108]

Look up the page on archive.org (maybe a little late)

[@japosaig9049]

Consulta....una vez configurado se puede utilizar en PS4 o solo puedo usarlo en pc?

[@Dansl05]

I've gotten everything to work including FFB, but now it has stopped working consistently and keeps showing that the wheel is connected with firmware version 0.0, but it can still detect wheel movement (this is only in the software, and games don't see any wheel movement). I didn't really understand the Z toggle, that might be my problem. Is there anything i should try?

[@samedsipahioglu5066]

hi, I have 400 ppr encoder. I am usingwheelconfig. if I turn wheel left one tour and wheel come to zero point, this zero point not a zero point. 5-10 degree slip my zeropoint. and when I turn left, wheel more force doing me than right side.

[@vinncentt6289]

Does it work on android driving simulator games too?

[@Mahir-dl2ik]

Can you add a paddle shifter to it besides H-shifter? Please reply.

[@joshmessinger113]

Why not use potentiometers for steering as well, instead of an encoder and timing disk?

[@realmira5138]

Encoder can rotate unlimited times and is more precise

[@islamrepo]

how do I do just the pedals, like I do not understand how to program them

[@dirtymyloofficial]

Hi! Works without streeting wheel? (Just Pedals,shifters,andbuttons/handbrake?)

[@galingrudev3599]

Can I use mouse sensor with cd disc instead printer encoder

[@galaxyeast4660]

Can I make the pedals only and use the format for the Arduino to become standalone or do I need the steering wheel too because I just want only the pedals since mine doesn't have a clutch so I'm building one with one. (sorry for bad English)

[@gamingseries2846]

sorry to ask where can i buy theses parts

[@atmostvg777]

Bro does this code work if we use push button instead of potentiometer in pedals

[@EdnoAverche]

Hi there! I am going to be using a leonardo in a Logitech MOMO racing wheel. The wheel itself has a PCB that reads a white line on the shaft so it knows when the wheel is centered. How do I go about connecting this to the Arduino board? Do I hook it up to encoder Z pin? If not, how would the wheel calibrate itself? I'm using a motor with a built in encoder /the factory momo one/.

[@AgaYuditraStudio]

+iMario i dont know what momo wheel use. You can use motor with built in encoder, but if you use ratio for your motor, you must calculate PPT with ratio.

[@EdnoAverche]

AgaYuditra Studio Got it, thanks!

[@mandirabarai989]

Can we use computer mouse instead encoder + Timing Disc

[@immax78]

Good day. The problem is that the steering wheel is not calibrated: (The rest of the steering wheel works fine, there are no problems.) Frankly, there are no more ideas, but I have not tried it. PWM + Dir and 20KHz, then the motor starts to spin at a high speed in one direction, and at the same time it does not react to pressing the calibration button at all. From time to time, after you reinstall everything 100500 times, it happens that the steering wheel reacts to the request to start calibration ... but at the same time just a short time turns in one direction ... and then freezes, issuing an error about that , that calibration failed (Calibration Error).It often happens that when you press the calibration button, the Device Status turns into the search mode some sort of index (Seaching index) ... and again nothing happens.The encoder is configured correctly, namely 900 degrees in the game = 2.5 turns of the rudder (also 900 degrees). In other words -> everything is set up perfectly! And again, again, while everything else works: the encoder, pedals, buttons, etc. You can tell me something, but my ideas have already ended. Thank you in advance.

[@luka5144]

I'm having the exact same problem and im going crazy because of it. Did you find any solution to this? Thanks for any help

[@TheLiamerator]

Xloader keeps failing to upload hex file. Tried everything. Giving up...

[@prodrive8381]

Hey guy how to use extra button I don't understand what it is used for.

[@AdeAhmad]

AgaYuditra Studio >> untuk kalibrasi harus pake AIWAVE dan DXTweak apa bisa salah satu ya...

[@AgaYuditraStudio]

AI wave itu adalah software seting utama karena di situ ada setingan derajat setir sampai FFB, kalau DXTweak itu hanya untuk kalibrasi potensio di bagian pedalnya saja.

[@AdeAhmad]

AgaYuditra Studio oke mas... trims pencerahannya... ijin ikut belajar ya...

[@ImprevisibleDev]

can i use a potentiometer instead of an encoder and a timing disk ?

[@abdulmuiz6875]

Can we use potentiometer with steering wheel

[@ignaciotantos1075]

hi i have one question if i use a encoder of speed is like you show on te video because in my country i cant found the traduction of what you put on the video?. another question if i use one encoder for the arduino what tipe of timing disk should i use?. thanks for you answer

[@jagan5779]

Is arduino uno able to be replaced in your work?

[@Metxdd66]

Hi. During attempting my own build i came to a trouble. In RFR i am not getting any axis response from encoder and Arduino itself is recognized as 4 axis 32 buttons joystick. Im using HPCB781-80006 encoder and, what is imo reason, Arduino Leonardo, which i found out probably is chinease clone. Aruduino itself works, after mapping Z-toggle to buton it works fine in RFR. Any recomendations? Should i get some Arduino drivers or change encoder to like f.e. CWZ6C or just first get OG Arduino. Great work and thanks in advance

[@ohividy2093]

can you tell me where to find the pinter encoder and timing disk

[@AgaYuditraStudio]

If you cannot find printer encoder, You can use incremental encoder.

[@306D1]

My pedals are so sensitive. I have 10kohm potentiometers maybe i should try diffrent pots!? DXTweak is changing something but not really much. Maybe i just dont know how to use it

[@AgaYuditraStudio]

+Berthold maybe your pot is broken,

[@306D1]

AgaYuditra Studio Can’t be broken

[@ET-DAH]

Halo gan, mau nanya lagi nih, ane kan udh bikin, tapi klo button nya cuma 2 rasa nya kurang, klo pakai Stick PS (stick wireless) conect ke Leonardo nya gmn ya? biar tombol stick nya bs ditempel di Setir nya.. Thanks

[@AgaYuditraStudio]

Kalau pakai stik PS gak perlu konek ke leonardo. Stik Psnya berdiri sendiri.

[@yansahkorg1876]

Hi friend, I want to ask if the disc is just random, right?

[@Z00fa]

Could this be made by changing the encoder for a 10k potentiometer? It’s easier to get and less difficult to use but i don’t know if this software will allow it

[@ayushdeore4977]

Can i use a potentiometer in replacement of encoder? Cause i dont have a printer.....waiting for your response

[@AgaYuditraStudio]

No, you must use encoder

[@BinkvH]

Can you use an Arduino Nano instead of an Arduino Leonardo? I only need an H-Shifter and I can buy a Logitech one for a bit more than the price of a Leonardo.

[@maxovik665]

I write through an interpreter. the question is whether it is possible to replace the encoder with a multi-turn resistor

[@AgaYuditraStudio]

no. this firmware just for encoder.

[@muhammadbintangelanyusyafi9999]

Ada template cetakannya gak utk h shifter,steer, sama pedal?

[@emi-namnam]

could a rotary encoder be used instead?

[@josueherrera8547]

What others encoders and timing disk can be use? Thanks for answering

[@AgaYuditraStudio]

You can use like incremental rotary encoder on ebay.

[@josueherrera8547]

i found the incremental encoder, but work same that the what you used? and can it be any incremental encoder?

[@AgaYuditraStudio]

If the encoder have 4 wire. It will works same with my tutorial. Wiring vcc, gnd, signal 1, signal 2. But you must check the datasheet of encoder, vcc need 3.3v or 5v.

[@aldi7954]

Ada tutorial assemblingny mas?

[@restorationpassion3920]

I would like to know what Potentiometer you used thanks

[@AgaYuditraStudio]

I use rotary potensiometer 10K

[@izrylut1653]

can i replace the printer encoder with standard encoder or potentiometer?

[@AgaYuditraStudio]

You can use incremental encoder, but not potentiometer

[@moronimanriquez7913]

Hi, what other encoder models can I use? Because I can't find Canon Pixma

[@ziahaider6793]

Brother i try every thin (try from windows xp,7,10 and alot of time reset button press 2x install driver change cable) but cant upload file from xloader. is there any other way to upload the file?

[@ziahaider6793]

i got a solution ( connect board open mangier see the port number then press reset button 2time same time see port number again that will change then go to xloader and press rest button 2time and fastly select port and upload) like this only can upload frimwear.

[@onurboyaci5147]

Hello mate, i want to build my steering wheel but i'm not sure which one to use arduino leonardo r3 or arduino mega 2560 ch340.Which one is better for me? Thanks a lot.

[@AgaYuditraStudio]

Arduino mega using chipset like arduino uno. So you cannot use it for this project.

[@bhimratnanikam9512]

Sir encoder can't found can I use another encoder

[@AgaYuditraStudio]

Yes you can

[@victoralejandrocanteraherr9003]

Other encoder? What can you use? I can't found the encoder of the video

[@AugustoCabrera]

@@victoralejandrocanteraherr9003 you can use something like this articulo.mercadolibre.com.ar/MLA-796294091-encoder-rotativo-incremental-100ppr-ab-ttl-diam22-eje-35mm-_JM

[@informbyhuzaifa3964]

how to buy timing disk and other things plz tell me soon

[@MaisthaTutos]

Hi, I'm trying to do this project actually, I have the pedals Al ready done and working, I have the encoder from an old printer and I'm about to do the steering wheel, but any of you knows with which games will this be compatible with? I have already tested it on Euro truck simulator and it worked perfectly, also tried on rFactor2 but it didn't worked so I don't know which games I will be able to play, if any of you knows I'll appreciate it a lot. Also if you are starting I can help you with any questions you have

[@NikhilNikhil]

When I tried to upload the file from Xloader i got a notification saying upload failed. Can you please help me. Thank you