Love your videos. Have a 93 accord ex with 500k on her. Been slowly rebuilding it. Someone busted out my passenger side window so now replacing both regulators and pass motor. These videos have been VERY useful. Keep it up!!!
@cartersense4 жыл бұрын
Just bought a 92 LX. Interior great and runs great. 280,000 miles. Drivers window went off track this week and here to find the fix. The regulator seems to work fine, will find out why it disconnected from glass.
@elijahdonovan20842 жыл бұрын
exact car and exact problem on same window. kinda funny lol
@jamesaanderson44486 жыл бұрын
Notes: Tape the window in place with two straps of tape over the top of the window frame before unbolting regulator. (prevents the glass from falling) Second: the door lever assembly gets removed from the door card by prying at the front, while pushing from the rear on both top and bottom between the edge of the card and the lever assembly. (there are two clips top and bottom than push forward to release) These clips were apparently previously broken off on Winstons car. (and on mine now too) The plastic is very brittle, so they may break anyway. But it is worth a try.
@troysamuel55076 жыл бұрын
Five stars. Just used this to guide me through pulling mine out. I did take it a little further and replaced the plastic gear at the head of the motor that pushes regulator. Mine was stripped and would stop once it meet that flat spot. Good to go again!
@thomasseitner80848 ай бұрын
Tank you for providing this video. It was helpful to me, to find out the spring(no new grease) reload after replacing the 3D-printed gear (greased) inside the gearbox. (93 2.0 accord shifter 205tkm) greetings form austria
@forgivendrifter73265 жыл бұрын
Man bro, good video. As lots of people said, mines doing it as well. Buddy of mine said it was the weather strip causing it to go shooting off. Mine rolls up and out past the rubber at the top. Unfortunately all my window regulators are gonna need replaced on my 93. Thanks for a great video!!!
@joseescobar62986 жыл бұрын
I am not sure if you still reply to comments, but my driver side window refuses to move at all. I am unsure if it needs grease or the motor blown out, but I love how well everything is explain in your videos and it is aways good to see someone else who enjoy cb7 also
@winstonbuzon6 жыл бұрын
Jose Escobar If it refuses to move completely, check your other windows to see if they move. If they dont, check fuses. If they do, you have a bad regulator or motor
@phillipmitchell40583 жыл бұрын
Very helpful video I will be trying this on my 93 accord 10th anniversary thanks 👍🏽👍🏽
@jrburger19875 жыл бұрын
Awesome now I can get started fixing my Honda that I just bought
@stevanaeastwood80592 жыл бұрын
Thanks Winston! You the best bro. Happy 2022!!
@vincerodriguez77627 жыл бұрын
Thanks Bro! Just bought a 91 Honda Accord LX with this specific problem!
@winstonbuzon7 жыл бұрын
Vince Rodriguez You're welcome and glad my video helped :)
@DiegoHerrera-fr8gg4 жыл бұрын
After I failed to install it on my own..93 accord lx.. look around for some help. Those white clips on the window. came off as I took the glass off (carefully). went to get some 3m sealant to place it back on.. By the time it dried up......... it got dark.... day 2 (4-17-20)......i hit the sub button.
@Elias.G215 ай бұрын
My 92 accord recently got this problem time to buy a new regulator since the rear windows have new ones too
@head09276 жыл бұрын
Great video i just picked up a 93 ex 5speed with 139,000 original miles and the window regulators are bad on the back and this video definitely makes it look stupid simple. Side note the brakes on this car is some straight BS. Lmao
@StrugglaREP9 жыл бұрын
Nice Video! Was waiting for this one. Now I can figure out why mine wouldn't even roll up or down lol Thanks for another great vid !
@winstonbuzon9 жыл бұрын
***** Thank you, Struggla! You might also want to make sure your window run channels are in good shape, and dry lubed for best results. And you're welcome! :)
@StrugglaREP9 жыл бұрын
Thanks man! Will do! Having some cluster problems :( so trying to resolve that before I continue on.. Staying tuned to the channel for sure
@natehopper25935 ай бұрын
Mine do the same brother like he said make sure they stay in the correct area and that the motor itself is connected and moving the part that holds the glass. I’ll be replacing the whole motor and guide as motor moves but it doesn’t move glass because the guide attached to the motor isn’t moving
@LuisSanchez-pd7qe9 жыл бұрын
Now with the windows off perfect opportunity to tint them;) Nice job bro
@winstonbuzon9 жыл бұрын
Luis Sanchez Easiest way while the window is out... Thank you
@patrickdana28268 жыл бұрын
Great video, thanks for posting Winston.
@winstonbuzon8 жыл бұрын
You're welcome :)
@elijahdonovan20842 жыл бұрын
this cleared up a question ive had about my 92 accord lx sedan! XD mine is doing the same exact thing on the driver side window and i thought it was the seal but it looked fine? i was so confused but this cleared it up. THANK YOU!!!!!
@Kyoju2528 жыл бұрын
I'll be doing this to both my rear windows soon.
@G888-b5j6 жыл бұрын
Did I miss the part where he put the glass on the Regulator?
@41mickey412 жыл бұрын
Thank you that really helped
@ShuffleToExpressss9 жыл бұрын
You just saved me a hassle aha :) Great video helped me a lot Thanks
@andremickenssr.3188 жыл бұрын
Much appreciated! Great video....thank you!
@winstonbuzon8 жыл бұрын
Thank you and you're welcome :)
@vortmax19816 жыл бұрын
Very helpful video, thanks!
@TheMrBoar7 жыл бұрын
thanks man, I will try it out today
@juanreyes40512 жыл бұрын
Hi Winston I hope you seen this because I have a big question for you about the bolt/screw that you screw on 6:54. Do you know what it is because it look like gear ⚙️ on my 1990 Honda Accord ?
@omarshatila98348 жыл бұрын
YOU = AWESOME !!!
@D.Ashlaw1172 жыл бұрын
This is gonna be fun for me because my window motor went bad and it’s stuck all the way up. So I can’t move mine to access the bolts 😂
@malamigo913 жыл бұрын
Great video! Great help!
@jadenbeck99448 жыл бұрын
Great video but I had a question about your door panel. Mine has the fabric on it but it's coming off but is leaving a blue glue residue. My question is how did you take it off your door panels? Thank you
@winstonbuzon8 жыл бұрын
I just sanded off as much as I could just so the surface doesn't have too much residual glue before I applied the new glue
@getmulah6197 жыл бұрын
great video man! helped so much!
@Kiwitakimago4 жыл бұрын
How snug did you tighten the bolts that attach the frame to the glass?
@winstonbuzon4 жыл бұрын
Hand tight
@BrianOfAteionas8 жыл бұрын
My window is completely seized. Wont roll up or down. The switch is good, I can tell because I can feel the effect it has on the system with I push it, and occasionally the regulator will make a grinding sound. I'm sure the motor is fried / gear is stripped. Any suggestions?
@messiasrevoredo95983 жыл бұрын
👍 yes
@donaldross32135 жыл бұрын
yo I loved the vid very,very helpful you da man
@winstonbuzon5 жыл бұрын
Thank you for the comment! Much appreciated 😁👍
@josearana770411 ай бұрын
Will this make all my windows work?????? Cuz I have a 4 door car
@Darksilverjesse7 жыл бұрын
93 honda accord anniversary: been searching for this type of video and all I kept finding was people who were pissed off and cussing the whole experience or people who didn't know how to mount a camera while they work. I swear the one was recording from their shirt pocket. SMH
@hasanamini255011 ай бұрын
Thanks
@everythingsj2 жыл бұрын
hey Winston! i have a 93, my drivers window was working but would roll up off track leaving a gap. it eventually stopped working and when i press the switch it makes a single click noise. my rear passenger side started to make popping noises when rolling it up. it gave out leaving a crack & it occasionally moves a pinch when i go to roll it up or down. the glass is wobbly now though. is it the regulator & motor ?
@winstonbuzon2 жыл бұрын
Probably the whole assembly (motor and regulator)
@everythingsj2 жыл бұрын
@@winstonbuzon thank you!!
@winstonbuzon2 жыл бұрын
@@everythingsj Anytime
@XXKILLERCALI2139 жыл бұрын
Nice video
@winstonbuzon9 жыл бұрын
Gabriel Rodriguez Thanks! :)
@Bluekbizzel_gaming7 жыл бұрын
Which regulator did you go with? I'm sure not factory, I gotta replace mine think ima go with Dorman.
@winstonbuzon7 жыл бұрын
K Brown Dorman is good enough
@Bluekbizzel_gaming7 жыл бұрын
Cool, the front windows barely go down. Back ones work enough for now. Just replaced starter and alternator. Gonna do the window regulators next. But thanks for the answer and digging your cb7. Hope to see more vids
@Gleamyred7 жыл бұрын
for some reason my CB7 window regular has a 2 prong connector and not the 4, just got a part and figured this out :/
@mariocmo13 жыл бұрын
Can you do a video on a coupe
@winstonbuzon3 жыл бұрын
If I get a chance to get my hands on one, I will
@rubencastillo69703 жыл бұрын
Do you have the link to where you bought both the front and back regulators??
@winstonbuzon3 жыл бұрын
No, because I just got this off the junkyard
@rubencastillo69703 жыл бұрын
Oh ...well I guess it's time to go hunting for some😂, thanks...good informative video too 👌💯
@raulcastro18244 жыл бұрын
How about a instructions for 1991 Honda accord coupe
@DragonusDrako3 жыл бұрын
Do you need the new motor or is it just the regulator that is bad?
@winstonbuzon3 жыл бұрын
The regulator is really bad
@DragonusDrako3 жыл бұрын
@@winstonbuzon Well I bought the regulator but not the motor. Do I need to replace the motor too cause my window is doing the exact same thing where it's leaving a gap.
@winstonbuzon3 жыл бұрын
@@DragonusDrako only replace the motor if it struggles to open or close. If the window gets dislocated as it closes, then regulator is bad
@DragonusDrako3 жыл бұрын
@@winstonbuzon Yeah the motor seems fine as far as rolling the window up and down. The window just doesn't go up straight and leaves that gap like yours. Just trying to make sure I don't need to replace the motor before taking the door apart if you get my drift lol.
@elijahdonovan20842 жыл бұрын
also since it looks very easy to take the windows out i might just take my windows out to tint them. XD
@daniellucero46874 жыл бұрын
How can i get my driverside window up untill i can buy a regulator?
@winstonbuzon4 жыл бұрын
kzbin.info/www/bejne/l4TImJeQl7FoacU
@Rachidlebanon3 жыл бұрын
Hello why every time you change and put new one U cannt fix the old one Cannt all see you to change to new one
@winstonbuzon3 жыл бұрын
There's no new ones. All regulators are at the junkyards, coming off the cars that have them. So every time they break, got to go to junkyards for replacement. Plus, it's a lot of work trying to fix the old ones anyway
@raulcastro18244 жыл бұрын
Mine is a 1991 2door coupe my drivers aide window will not roll up
@winstonbuzon4 жыл бұрын
Same deal then
@nicosantana44105 жыл бұрын
How about a video on the rear windows?
@winstonbuzon5 жыл бұрын
When I get a chance to work on another
@nicosantana44105 жыл бұрын
@@winstonbuzon thanks, appreciate your videos. Very helpful. How do I know if the window motor or window regulator is bad?
@winstonbuzon5 жыл бұрын
@@nicosantana4410 slow movement like its struggling, or just no movement at all. I would test it using a 9 volt battery
@nicosantana44105 жыл бұрын
@@winstonbuzon no movement at all
@winstonbuzon5 жыл бұрын
@@nicosantana4410 bad regulator
@HondaxPower8 жыл бұрын
Soo I have too ask How good is a h23 and what kind of transmission do you have? Would u recommend a GSR one?"
@winstonbuzon8 жыл бұрын
H23A just has a slightly bigger displacement and HP to Torque Ratio are closer. I used my stock Tranny and it fits well. I don't know if a GSR tranny will be needed
@HondaxPower8 жыл бұрын
+Winston Buzon (DubEezy) Soo then you still have the stock transmission with a basic clutch on a H23A ?? What would B the Redline on that Bad Girl??" You have right now ??
@winstonbuzon8 жыл бұрын
+HondaxPower Haven't had the chance to test. Waiting for a new tachometer before going to the dyno
@HondaxPower8 жыл бұрын
+Winston Buzon (DubEezy) ok will I Would love too know More About it CUZ I also do have a CB7" and I'm trying to put in a H23A in it but I don't know about the transmission ?? I need this car too win a EVO 9" that my bro has" too show him that Honda don't play!!" :D
@winstonbuzon8 жыл бұрын
+HondaxPower When I finally do the dyno, I will be happy to show the numbers and all
@TheLatinlover95746 жыл бұрын
My it dosent even roll up or down
@crackseller3217 жыл бұрын
need passenger side video
@XXKILLERCALI2139 жыл бұрын
Racing rival make a video
@winstonbuzon9 жыл бұрын
Gabriel Rodriguez I can make a lot of videos, but is there anything in particular you're looking for?