DJI Mini 2 Flexible Cable Also Cause Stuck Gimbal [ Error 40002 ]

[@razielfromhell]

A very helpful vídeo, I'm watched step by step and did change my flat cable on my mini 2 and it worked on the first try!! I'm so grateful to you!!

[@MRStrait5711]

Very nice and quick instruction. Thx a lot and thx again for your remote support!

[@djiSolutions]

Thank you my friend, have a nice day

[@DrFailov]

You totally right, 3-in-1 flex cable is one of most "popular" problems for mini1 and mini 2. Luckily, this cable is really cheap 😊

[@DJIDudeX2011]

I got mine on ebay for only $25 meanwhile dji is selling is for $38

[@terr20114]

Thanks for the detailed video. After the crash the little rubber connectors for disconnected so I picked it up with the gimbal outside the drone hanging by the cables. I opened it up, attached the cabled and that's when I got the error. The gimbal moves initially in the startup then it gives the error. I opened it before this video but I did not notice any damage on my quick inspection. I will need to inspect again later. Since the gimbal works initially. Would it be more likely that the cable is the issue?

[@wergsion9190]

Good example, lucky I check the gimbal first and see like you show, thanks, good video

[@djiSolutions]

Thanks for watching!

[@skippy7904]

Merci beaucoup pour ta vidéo, grâce à toi j'ai pu réparer mon mini 2 😊👍👍👍

[@djiSolutions]

I so happy then my videos can help you ♥️

[@franceeadventure7962]

Excellent job! very informative, just subscribed, i have problem my mini2 crashed and broke the gimbal shock support, can you make a video on how to disassemble and assemble the whole gimbal for DIY purpose, and also please show what tools to use to remove the bearing from the gimbal, thanks a lot.

[@etiennem.3191]

This is so illuminating, thank you so much! I would like to ask you if the PTZ cable of the mini 3 is compatible with the mini 2?

[@DrFailov]

Very important: because of glue which holding connectors it's easy to damage board. So i highly recommend using heat gun when didconnecting it, especially for bot experienced engineers

[@djiSolutions]

Ok I will try it next time

[@alikasnak5264]

Sen bi harikasın bunu deneyeceğim teşekkürler 🎉

[@djiSolutions]

Thank you 😍

[@geraldoleonelribeiro769]

This video is so helpful. Thanks from Brazil! Just did the substitution on my drone and totally worked!

[@djiSolutions]

Thank you, hope it help

[@DlightingGuy]

Will same method work for replacing Flexible Cable on DJI Mac mini (1)?

[@patent_films9123]

After ribbon flex replacement mini 2 was multiple errors, (imu, visual,camera malfunction), before was no problem, fly normal, one Thing interesting, Theo flex Will broken code is 1168, The New is 0616, in your case work, but here were the same errors, ant suggestion?

[@djiSolutions]

I have never see those error number

[@rcartier1325]

Crashed my mini 2se and gimbal was stuck. was able to get it free but now wont move with remote. Took the case off and touched a few things and started working again. I put the case on and now won't work with remote again. Does this sound like a cable issue?

[@saidalmohtarif3791]

thanks bro

[@farhanfaiaj751]

Hi sir, I've got a problem with my Mavic Mini, when I turn it on, it works normally, the gimbal top motor starts moving normally and check axels but pitch and roll motor don't move . Why its happening? At first which cable i need to change (ptz or flat cable) ? I'm waiting for your suggestion. Thank you

[@djiSolutions]

The ptz cable have problem, replace it

[@farhanfaiaj751]

@@djiSolutions The ptz cable and 3in1 flat cable both are okay . But both roll and pitch motor not working.

[@glademer_a2735]

Is there any specific name of flexible cable ?

[@djiSolutions]

Check our link in the description. PTZ Gimbal cable

[@joller79]

mini 2 with error 40002/3 gimbal stuck or overload, different at times, changed the 3-1 cable, but same,,, gimbal works in 2 ways, but not yaw??? left right..ideas? it might be logic board, due to water damage sticker is read maybe?

[@przemysawszczygielski3676]

I changed 3in1 cable beacause it was damaged after crash. After change i have this error (40002), should i change again this 3in1 cable or my gimbal is broken?

[@djiSolutions]

You should change both flexible cables first. If the it work, it your gimbal problem

[@przemysawszczygielski3676]

Thanks, i will get know if gimbal signal cable change Worked

[@przemysawszczygielski3676]

It Works! After change gimbal cable error gone👍🏼 thanks😊

[@djiSolutions]

@@przemysawszczygielski3676 Great job 👍

[@sayednaqvi1568]

Can the flex cable cause issue in the Gps module of the mini 2 as well?

[@djiSolutions]

Yes sure

[@sayednaqvi1568]

My dji mini 2 has gps issue it has sattelites like 6/7 and it shows low gps signal and takes off but won’t go above 4/5 meters . In between it gets 8 sattelites and gets the gps but after some time of flying loss of signal and attitude mode …so what do you think? It’s the Gps module or flex cable ?

[@djiSolutions]

@@sayednaqvi1568 it mean the GPS module is old and can't get much signal or sometime is about the your environment. It not about the flexible cable

[@sayednaqvi1568]

@@djiSolutions thank you very much for you’re reply . Really means a lot .

[@TijnVos]

I have error: 40012 (Gimbal) 30066 (IMU) 30049 (GPS) 30007 (GPS) You think this is also caused by a broken flex cable? I have reconnected it but still error.

[@djiSolutions]

Too many error, you should fix one by one

[@TijnVos]

@@djiSolutions nah sold it already, bought a second hand mini 2 😄

[@djhuzi]

After a30 meter crash, the vertical movement of gimball won't work. I have change the multicable + flat cable, but nothing. The little connector of motor Is inserted. What i can do? Movement manually Is fluid.. Sorry for bad english

[@giovannigatto1974]

again top! after i changed the cable the gimbal is ok but now a navigation system error 30008. how can i fix it? thanks!

[@djiSolutions]

Does it let you fly the drone? If it not, check the GPS cable

[@giovannigatto1974]

@@djiSolutions no, the drone does not fly. I removed and re-inserted the cable to the gps module but it does not work, always error 30008. then I bought another gps module but always error 3008. what can I do now? thanks for your help.

[@giovannigatto1974]

What is GPS cable? is the 3 in 1 cable?

[@javierrios7471]

Buenas tengo el problema de la cámara que con el control del mando no se mueve pero cuando enciendo el dji se mueve la cámara fue desde que tubo una pequeña caída puede ser el cable o lo tengo que meter en algún ordenador para reiniciar gracias por el vídeo

[@djiSolutions]

You should have error. So we should find out what error you have.

[@Chinatownzs]

​@@djiSolutionsI have same problem

[@sachinkhekale1417]

Reporting cost Kitna aayeg

[@sportshighlights8708]

My gimbal moves when turned on and it auto calibrates but won't move when trying to move it with remote. I has been sunk in water for 2-3 seconds.. could this cable be the problem?

[@djiSolutions]

when you turn the drone on, if the gimbal is moving up and down. It not the cable problem. Try to reset any setting on the remote or try new remote control

[@rao.4354]

Is 3-1 flex cable in mini series all same ?

[@djiSolutions]

Yes

[@rao.4354]

@@djiSolutions thanks, dude. Love ur work !

[@plantitprofit]

My cable fixed the probelm, but now i get a "power system failure" code 30210" bad ecm? i used to get start up tone and thats gone now too. any tips?

[@djiSolutions]

Sorry I dont know too

[@captainboreg7797]

I’m not a surgeon, is there another way?

[@TheUrbanlife-Ph]

😂😂😂

[@sachinkhekale1417]

How cost to repear

[@oieceoa7187]

Yes my gimbal is not broken, it because of that cable

[@djiSolutions]

Yes mostly is flexible cable is the problem. Change the cable first because it cheaper then gimbal

[@williamapaumarfo251]

Hello, my crashed and the three in one gimbal cable got ripped. But anytime I replace it, the cable burns

[@djiSolutions]

Burn? Wow I never meet that problem, sorry

[@invertedaircraft8063]

How to fix error 40028 for mini 3? It is another gimbal stuck error but not the same as error 40002

[@djiSolutions]

Sorry I never meet that error, but I think it still stuck gimbal. It could be cable or gimbal itself.

[@احمدعبدالدايم-ه4س]

ما سبب ظهور خطأ 40027

[@seagiy4162]

But I already change gimbal and I notice that it not about the gimbal 😂

[@djiSolutions]

You should clear the gimbal first then change change flexible cable then change gimbal. Because gimbal is very expensive

[@howardtownsend3139]

With power off, flick it hard with your finger on all four axis before you try any of this shit. Mine came back straight away!!