DOC HARLEY: CHROME SWITCH COVER INSTALLATION

[@Slider7]

Worked like a charm. 20 minute job swapping out the covers. Glad you provided both versions. The M8 that I currently have is by far the easiest ones to swap out compared to my previous pre-M8 ride. Thank you!

[@elithegreat6463]

To the do it yourselfers , those “Clicks” are the most satisfying sound we can hear 👂👍🇺🇸

[@robertspencer2917]

Hi Doc I have been down that road with my old 07 Street Glide. changed out all switch covers to chrome. It wasn't to bad. I now have 2015 Ultra Limited and changed all my controls to the lighted ones. So much better at night well worth the money. Thank you for making these videos.

[@holdfastmackinaw]

Thank you!! I read the reviews on the HD website and was worried. It wasn't an easy task but WAY easier with this video. Thanks Doc!!

[@bikersoncall]

After 6 mins I decided that I really like my plastic swithc covers. :)

[@cjmueller5455]

The time spent doing this is time that could be spent riding.

[@bikersoncall]

@@cjmueller5455 I can't get enough chrome, but I'd screw this project up in a heartbeat.

[@rafaeltorres8451]

@@bikersoncall , I did it and it was easy.

[@bikersoncall]

@@rafaeltorres8451 Cool, thanks..

[@twouppers4541]

@@cjmueller5455 ikr

[@CandyBarMoto]

Thanks doc... but what a bout installing Switches with Back lighting ?

[@bikersoncall]

Back lighting, that would be cool at night for sure.

[@andyhailes9120]

Hi Doc, Great video as usual...As a new Harley owner in the UK I've found all of your videos to the point and really helpful for understanding everything from this subject through to belt tensioning and more complex things...A video on tank removal for a 2019 M8 lowrider would be great.. Many Thanks.. Andy

[@LowCountryHarleyDavidson]

Thanks Andy for your support. Removal of tank can be covered under the ownership of the Factory Service Manual. If you are working on your bike, I highly recommend…..Doc

[@andyhailes9120]

@@LowCountryHarleyDavidson Many thanks...I have access to one but the videos always make it that much clearer...Andy

[@richardwesthafer3769]

Thank you for your video.I had crud inside my signal component so you showed me how to take it apart to clean.Thank you very much

[@babybugspaw7085]

Dude! I mean Doc! You’re a man of teacher! Enough said, thank you!

[@LowCountryHarleyDavidson]

Thank you for your support….Doc

[@rusnsc7622]

Glad my 11 FLHTK had chrome covers! That swap would have challenged my patience to be sure. Thx Doc.

[@Jimmy_Jim_Jim_1234]

The extended turn signal thumb switches are awesome. I highly reccomend it. I wish they used both signals on the left thumb like everyone else in the world.

[@TeensierPython]

You do eventually get used to it, but why H-D? Just do it like everyone else.

[@Jimmy_Jim_Jim_1234]

@@TeensierPython the integrated left thumb set up is much better.

[@TeensierPython]

@@Jimmy_Jim_Jim_1234 agree. I ride something else for a while and then have to re-remember how to turn on my Harley. Is nice having the self canceling signals though.

[@mickc4633]

I thought the switches were the same from 14 and up? In the book they say they’re the same I run out 14 CVO and I believe the switches are the same all the way up . Your thoughts

[@Axel0204]

Hey Doc, the controls that you are referring to as Milwaukee 8 controls are are also on 2014+ Twin Cams. I've had a 2014 Street Glide & a 2017 Softail Slim and they both had that style of switch assemblies.

[@liankyson9161]

i know Im asking the wrong place but does anybody know of a tool to get back into an Instagram account..? I was stupid forgot my account password. I would love any help you can give me!

[@lucasalexzander8988]

@Lian Kyson Instablaster ;)

[@liankyson9161]

@Lucas Alexzander I really appreciate your reply. I found the site thru google and im trying it out now. Seems to take a while so I will get back to you later with my results.

[@liankyson9161]

@Lucas Alexzander it worked and I actually got access to my account again. Im so happy! Thanks so much, you saved my account :D

[@lucasalexzander8988]

@Lian Kyson You are welcome xD

[@joeneely8054]

Thanks Doc, but I have been looking for how to properly install the metal tabs for the pre-14 audio controls. Great video, still learned some things, especially on the M8 set up.

[@jeffbarr6816]

Thanks Doc from Australia, but I can live with the original covers on my 2001 Road King. Never like the words, "....the chrome plastic covers do not bend as easily". Enjoy your videos, very informative. Cheers.

[@henryfam58]

Thanks Doc, another great video. Really like the accessory install videos.

[@shakybucket1323]

As always, explained great 👍

[@larrybrown441]

As usual very good stuff but, would have mentioned the need to block the brake lever in a slightly depressed position prior to removing the brake operating lever mount.

[@flytheedge]

Hey Doc, can you do a video on the different Stage kits and when you'd want to add additional components to support the kits? You kinda touched base with this regarding the cam kits, but just wish you'd dive deeper into it. For example, if you do a Stage 4 131 kit from a 114 OE engine, do you need to replace the Crank or anything else to support the upgrades?

[@justanotherviewer52]

Looks like quite the intense job on the twin cam. I am going to do the brake fluid covers this year and I think I'll stop there. Though I probably won't.

[@traveltherightpath]

Hi Doc! How about replacing the buttons and harness? Start button is failing, I cleaned it with electronic spray but after a while started doing it again. I’m gonna have to replace them.

[@LowCountryHarleyDavidson]

Usually that’s a delicate soldier job. Take your time….Doc

[@richardwesthafer3769]

I want to add why didn’t HD add a seal gasket on that handlebar component?It would certainly help prevent moisture and crud from getting inside that module

[@ChrisHardwickanimaladventures]

Hey Doc, I just noticed my front engine mount on my 2007 Dyna has rubber bulging out of the mount, looks pretty bad, although I only have 20K miles on the bike. Looks like the guy before me kept dropping oil on it from oil changes. I'm thinking the front went out first because it's right under the oil filter. Can I change out the front mount now and the rear a few months down the road or do you need to replace them as a set? This bike needs a bit of work, trying to manage my budget LOL.

[@LowCountryHarleyDavidson]

Keep the budget. One at a time will work. Thanks ~ Doc

[@ChrisHardwickanimaladventures]

I got a question for you doc. I have my Dyna in neutral and when I give it some gas it pulls forward ever so slightly like the clutch is still partially engaged. Does this mean I have to adjust the clutch with an allen wrench under the primary cover?

[@LowCountryHarleyDavidson]

A full clutch adjustment - Cable and Allen (behind the clutch cover) would be a good place to start. New fluid at the right amount can also help. Too much primary fluid can cause this too. Thanks ~ Doc

[@stanwerner7484]

Doc, I have a 2019 CVO Street Glide, as you are aware the switch cover black with chrome housing they also illuminate. Question: If I install the Chrome switch covers in place of the "Stock Black" ones will the switch have the ability to continue to illuminate? -- thank you Sir.

[@LowCountryHarleyDavidson]

Great question!! The instructions detail that these covers do not fit CVO models. Which I believe have illuminated switches. There is not a kit for illuminated switches so I don’t think HD kits are made for illuminated switches. Once again, Great question 👍 Thanks ~ Doc

[@dejuanwilliams9197]

Chandler H-D Charged me $425 in labor to install the lighted switches! Never again. Thanks Doc!

[@edhickey3163]

should have been 1 hour

[@Handirifle]

Doc, this couldn't have come at a better time for me. One correction for you though. You said the old style was the twin cam and the new style the M8. My bike is a 2014 Ultra Classic 103" twin cam (Rushmore bikes) and it is the same controls as the ones you said for M8's.

[@LowCountryHarleyDavidson]

Thanks for the correction….Doc

[@BadBoyEzRider]

Is it easier on an older evo touring? Or just as difficult as the Twin-Cam? I need to replace switch on a 93 Electra Glide. The bottom section is stuck to clutch lever clamp.

[@LowCountryHarleyDavidson]

No not any easier....Doc

[@alisherfakhradov9638]

Thanks for your experience, sir

[@davidmitchell9048]

Great Info Doc, thanks..

[@glennthompson4166]

At his polnt , you should have mentiond ya ca also get extended turn signal switch covers ( which harley sells ) for people with short thumbs or thumb disablites ...

[@frankdavid6]

Hey Doc, I love your videos! Thank you. I need to repair/replace the “audio” thumb buttons (especially the MODE button in the throttle side control) in my hand controls (in my 2002 Road Glide 88” Twin Cam). Do you have a video on how it’s done or can you PLEASE do one? My old stereo is stuck in Cassette tape mode and the tape ribbon is torn so I’ve got no tunes now. Please HELP!

[@jamessturtz728]

Doc, I love all your videos. How about doing one with a step by step about installing the right side dash switches and wiring harness for the 2019 tri-glide ultra? I just installed the right side switches but am a little timid about electrical wiring.

[@guentherpenner5544]

Hi Doc I`m installing chrome levers and switch covers on a 2003 Softail Std. and when I was removing the switch cover and switches front the brake cover assy there was a small plastic banana shaped black strip that fell out. I`m wondering if you could give me some direction on were it`s suppose to relocate with the install? Thanks much appreciated! gunner

[@LowCountryHarleyDavidson]

I believe you are describing the black plastic piece that attaches to original clutch lever….Doc

[@guentherpenner5544]

No this came out of the front brake switch covers after removing the switches inside the the cover. The part is black about 1 inch long & 1/4 inch wide & has a curve to it. Also has a small pin hole in the middle. Looks like it may be some kind of pressure clip. Thank you - gunner @@LowCountryHarleyDavidson

[@johnnyjohns4574]

Hello Doc, I want to upgrade my clutch and master cylinder to chrome, bit I cannot find a video for it. I found your video on chrome switch housing. Any help would be appreciated.

[@LowCountryHarleyDavidson]

Sorry, I highly suggest a Factory Service Manual. It will give you step by step instructions. Other wise take it to your local dealer and have it installed. The clutch fluid has to be bled so the travel on the push rod is good enough to release clutch plates....Doc

[@ih8011]

For the twin cam what about the right side I took it apart and had 2 small metal pieces come out what are those for?

[@LowCountryHarleyDavidson]

Without seeing them, my guess is brackets to hold wires in place and the spacer that fits behind the brake switch….Doc

[@danielgaskell5490]

Thank you, Doc!

[@cjmueller5455]

Always great videos, Doc!

[@mikebodine4164]

Hello Doc I have a 2014 softail deluxe cvo I tried to get chrome switch covers for it but HD doesn't offer a cover for the cruise control. I did put the chrome covers on all other switches. I would very much like to get the chrome cover for the cruse control.

[@harleyhawk7959]

I know this is an old how-to video, I have an old bike. A 05 ultraclassic classic. my Chrome audio button fell off, I had Harley dealership install another it lasted about a year and fell off. I see there's a tiny copper insert the toggle peg sticks out has serrations on one side. where and how does the copper insert come into play? my fix isn't working.

[@LowCountryHarleyDavidson]

I am sorry but I do not remember and can not find in the parts book or Service Manual. My memory believes the switch is in the shape of a half moon. The little copper strip would be on the flat side….Doc

[@quicknarco8567]

It would be nice if the 2013 fxdb had lit controls like other models

[@StarTrekBro]

Hi Doc, My switch housing screws are so stripped and tight that even an extractor bit breaks. Any suggestions? For now it looks like im keeping my current bars haha

[@gmro-ronosinski5102]

Did both my 2013 Custom 1200C Sportster and my 2006 Ultra Classic. Sportster was easier. UC fought me all the way with all the smaller switches and radio controls. They look great BUT not sure I’d do it again. Changing out grips was way way easier! Did those on both bikes as well.

[@carystarke8000]

I suspect that my Horn switch itself is bad, ground wire is new and really grounded well now. The positive wire also new and so is the Horn. Test light shows pressing switch lights meter, but maybe it’s not delivering 12 volts to the Horn.

[@LowCountryHarleyDavidson]

Great diagnostic👍 if your meter is showing battery voltage you may not have enough amperage do to a corroded connection in the harness. Just to be sure, loosen the mounting nut at the horn and retest. Too much torque effects the horn’s ability to vibrate and honk…..Doc

[@dougfresh1341]

Good job.

[@TeensierPython]

I want to stage IV my bike. I went to school for automotive technology (mechanic). Can’t be that tough can it?

[@douglasstarcher3649]

V clip fell out of right andle bar control. Where does it go. I've looked at the parts diagram and it didn't really show

[@LowCountryHarleyDavidson]

Behind the Stop switch to keep it in place...Doc

[@gusdhesewana9607]

woww..... there's a rare bike at the background 🤩🤩🤩

[@ericdelung9109]

Hi doc how do you replace the buttons on the thumb controls on a 2012 ultra limited thank you

[@snomobila]

thanks doc! always great info love you and your channel.

[@rocket3me695]

Awesome video Doc! I was just thinking about doing this exact modification to my Vrod! Does the Vrod have the same control set up/ process as the twin cam?

[@warangel19761]

I was going to do this with my Vrod, Did you manage to get yours done? was it the same as the twin cam? Thanks.

[@garykozlovich5882]

Do you have to put a new zip tie 92 softail??

[@LowCountryHarleyDavidson]

It helps….Doc

[@Steverinomeister]

I read somewhere that Harley Davidson has kept the switches black because they’re government mandated and not really a pretty part of the bike. Kind of like the coil on my 2020 Deluxe, not the mandate part, the part about not being pretty. So, in that spirit, no extra chrome geegaws going on mine.

[@shawng7902]

So use a screw driver and not that trim tool fork that comes with them? Noticed you had it laying out with twin cam style

[@LowCountryHarleyDavidson]

Please use what is comfortable and working for you….Doc

[@edkrumeich3265]

Doc. Is this available for a 2021 heritage classic?

[@LowCountryHarleyDavidson]

Yes. I believe part # 71500441…Doc

[@edkrumeich3265]

@@LowCountryHarleyDavidson thanks. Tells me does not fit but I’ll try…

[@edkrumeich3265]

FYI. IT DOES NOT FIT A BIKE WITH FOG LAMP SWITCH ON LEFT TURN SIGNAL

[@richconstantino8485]

At one time you could buy a house or donkeys from the Sears wish books. How ironic that internet sales and Amazon put Sears out of business and they were the original ones to do it. Great video Doc. My big came with those on it. One less thing I had to do. Lol

[@drips_spiritx5068]

What type of plastic is the module itself made of the part with the pin yeah I broke it

[@LowCountryHarleyDavidson]

Sorry to hear of the break. I do not know the answer to your question….Doc

[@lawrencedavidson296]

What about a 04 1200 sportster custom

[@LowCountryHarleyDavidson]

Yes, Harley-Davidson offers a set of chrome switch covers for your Sportster. Part # 71804-03,,,,,Doc

[@robertcoe50]

Doc did they fix the heating Issue in the heads on the 2021 M 8’s?

[@LowCountryHarleyDavidson]

We are just receiving the 21 models. Would you willing to share your facts on a Heat Issue? And where these chrome switch covers fit? Thanks ~ Doc

[@chopperchopster]

chrome. I live in Phx Az. bright sunlight and heat LOL. Im good on the chrome as in I dont have any on my bike.

[@Liveharley1]

Enjoyed the the video, I just did my 2006 twin cam again they were faded. But a want to tell you, I bought after market e-bay and amazon both did not work poor design and quality, don't buy them! Buy the Harley ones they work. Take care Doc

[@miketodd8640]

Another well explained tech video. Now, how about this. Heated grip on a Softail M8. The direction from the MC are just about useless.

[@garrettwilds1039]

I wish I watch this video before I change my buttons cost me two sets and had to have Harley put them on for me

[@fredorman2429]

Chrome on the bars and the dash reflects sun which is distracting on long rides, especially with the sun behind you.

[@LowCountryHarleyDavidson]

Thanks for your input....Doc

[@matt8863]

Doc..Please roll a video up about the HD "death wobble"

[@LowCountryHarleyDavidson]

No such thing. I have addressed proper front end service and adjustment. Thanks ~ Doc

[@mickc4633]

Yeah that’s the same thing I have on my 14 twin can

[@aaronperry4156]

I noticed that you did not demonstrate a good technique for reinstalling the chrome caps on the early models. In fact you never reinstalled the turn signal switch cap that you removed. You also never fully removed the upper switch. What are you afraid of Doc? Installing them is the hard part! Taking them off is easy! The part we needed to see was the reinstallation of the chrome switch caps.

[@LowCountryHarleyDavidson]

Aaron sorry I disappointed you. Hoping you can find what you need on another place...Doc

[@gucci4871]

🤘🏻

[@bobrosso9147]

Doc...what's "Milwaukee 8?"

[@brandonheselton7510]

You didn't cover the volume cover for the twin cam..

[@LowCountryHarleyDavidson]

I believe it would be the same process....Doc

[@brandonheselton7510]

@@LowCountryHarleyDavidson umm no. I watched your video hoping you'd cover that.

[@dwheeler016]

Us Twin Cam people do not need or deserve chrome switch covers. "All Hail the M-8"

[@georgewetzel4380]

All that to replace black plastic with chrome plastic!

[@bobmurphy3723]

Or take it to a Harley dealership and they will charge you a thousand to do it

[@roadglide1745]

Bitchin..... Ride Safe