Does Cutting Oil for Drilling Metal Help? Let's find out!

Does cutting oil for drilling through metal work better than motor oil, bacon grease or other options? Tap Magic Cutting Fluid, CRC C3400 Truetap Cutting Fluid, Rapid Tap Cutting Fluid, CLI Syntec Premium Metal Tapping Fluid, Lenox, 3-in-1 Oil, used motor oil, bacon grease, and shortening tested as cutting oil drilling through mild and hardened steel. New twist drill bits used for each product tested. In a recent video on twist drill bits, DeWalt and Bosch did well but using a high quality cutting oil helps a lot. Thanks for supporting the channel!
➡ Thank you very much for supporting the channel: / projectfarm
➡ An easy way to find past videos along with products tested: bit.ly/2FCrBpk A big thanks to Jim for putting this together.
➡ Merch: www.Project-Farm.com
➡ Click here if you'd like to subscribe: / @projectfarm
➡ As an Amazon Associate I earn from qualifying purchases.
➡ Products Tested In This Video (in no particular order):
Tap Magic Cutting Fluid: amzn.to/34hSyZV
CRC C3400 Truetap Cutting Fluid: amzn.to/3aFb7Zg
Rapid Tap Cutting Fluid: amzn.to/2FL82LX
CLI Syntec Premium Metal Tapping Fluid: amzn.to/2EoWnSk
Lenox: amzn.to/31dImzw
3-in-1 Oil: amzn.to/3jbliYH
used motor oil
bacon grease
shortening
Videography Equipment:
Sony DSC-RX10 III Cyber-shot Digital Still Camera: amzn.to/2YdXvPw
Canon 70D Camera: amzn.to/31b5Gy0
Azden Microphone: amzn.to/34d3DLE
Go Pro Bundle: amzn.to/31aince

[@ProjectFarm]

I didn’t expect to see such a huge difference between the brands. A high-quality cutting oil makes a huge difference, especially on high-carbon steel. I bought all of the products and do not accept sponsorships. Thanks to everyone for helping support the videos through your generous Patreon support. www.patreon.com/projectfarm. I look forward to reading your comments and video ideas. Thanks again! Products Tested In This Video (in no particular order): Tap Magic Cutting Fluid: amzn.to/34hSyZV CRC C3400 Truetap Cutting Fluid: amzn.to/3aFb7Zg Rapid Tap Cutting Fluid: amzn.to/2FL82LX CLI Syntec Premium Metal Tapping Fluid: amzn.to/2EoWnSk Lenox: amzn.to/31dImzw 3-in-1 Oil: amzn.to/3jbliYH

[@kalebmiller4845]

hey there

[@joshua_J]

Instant click for my favorite KZbin channel!!! I wish you made more videos.

[@RedBeardOps]

I can not believe how fast you put this together... I only asked for it like 2 weeks ago! Thank you! 😂

[@Oatmeal2six]

How about possibly testing mower blade sharpeners/methods. It might be I tough test but I know project farm can pull it off!

[@Proillbelly]

Test the best File

[@CdeAguero]

I gatta say, I suggested this idea like 4 months ago, and specifically asked for 3in1 oil to be tested (even though it lost horribly). Its refreshing to see a KZbin account with 1M+ subs still listening to the fans.

[@ProjectFarm]

Thanks for suggesting this video.

[@therealbigfoot3076]

Word

[@oldrabidus2230]

And he still responds to his fans!

[@warrenadams2157]

I call him Mr. President cuz I think he should run the country and straighten it out ! he does a really good job testing products/answering questions. " Project Farm"#1

[@magicmushroom69]

I usually grab whats at hand, but am going to avoid 3in1 next time!

[@LPMutagen]

Machinist here. In 20 years I've never witnessed a head to head test like this. I always just used whatever was at hand in the shop and I'm surprised at the big differences in performance among a bunch of products that I would have assumed were more or less equivalent. Thanks again for the effort you put into these tests.

[@evanvokes1694]

at 20 years you missed out on trichloroethylene rapid tap which we lost due to david suzuki and ozone holey science. Nothing on that bench is in this class. you know very well it is used in the third world anyways just like R12 refrigerants but somehow these small volume useful materials are banned here.

[@ThePreyMantas]

@@evanvokes1694 40 year machinist here, I remember using that, I still have 2 cans of it that I still use. I wonder why he didn't have any Fuchs. Personally I thin they make the best CNC coolants/lubricants. I've tried some of the "so-called" good synthetics, but they aren't anywhere near as good and even though I mixed my 1-2 brix higher than recommended, the tables still rusted and it eat up the aluminum sub plates to boot! FUCHS won hands down and would have been a good addition to the drilling test.

[@tkermi]

10 year hobby level machinist here 😊 (my brother is a real machinist though messing around with 13000 mm Y travel Zayer and the like). I just use Dormer cutting/threading fluids and mainly just etanol for aluminum but haven't done any specific testing. I wonder if the film strength is only important when the tool hardness is close to the work piece hardness? In that case it could prevent some friction wear. But maybe with hard tools and soft materials like aluminum the heat transfer is more important. I have a gut feeling that for tapping the maximum film strength is beneficial.

[@LPMutagen]

@@tkermi i thought about film strength and tapping as well. It's interesting that, while this test exposes some big differences in product performance, we are still in the dark as to the scientific reasons for the differences. I wish I knew more.

[@ThePreyMantas]

@@tkermi Hey, sure appears that way, doesn't it... I've never worked with Dormer cutting fluids, so am uneducated on their performance, but based on my experience and PF's testing there seems to something to justify your observations. I use high sulfur based cutting fluids with tapping and found them to yield the best results both in finish and tool longevity. Stinks like hell, but then all the good stuff generally is being phased out like MEK, a solvent and some mentioned by others like old school formula Tap Magic. Back to aluminum machining, try some Diesel fuel as a cutting fluid. Works really well for tool wear, great cutting finish in either turning, facing and tapping. I'm sure it has to do with sulfur content...

[@michaelward9880]

I've been a mechanic and welder for about 40 years and I've found your videos extremely helpful in finding products that live up to their hype and actually work! Keep 'em coming! Thanks.

[@ProjectFarm]

Thank you very much, will do!

[@SouthMainAuto]

Draining crankcase and filling with tap oil 😂 Best results yet on the bearing test!

[@trollmcclure1884]

Absolutely. They are obviously doing something wrong with motor oils

[@gringadoor5385]

Good luck when temps get below freezing.

[@trollmcclure1884]

@@gringadoor5385 yeah, or high. Maybe it would hold. Maybe it's too expensive or toxic for us to use millions of gallons each year. Maybe it's silicon oil-based. It may be a good additive

[@dimmacommunication]

@@trollmcclure1884 It probably has to do with metals inside the oil, can't have many nowadays with DPFs and such.

[@trollmcclure1884]

@@dimmacommunication Metals create a protective layer and maybe some other magic. Why would you make tap oil so slippery tho? I'm still confused

[@jaywest4102]

So many products I use just because it’s what my grandpa or dad use. Most of your tests show they were usually choosing wisely

[@ProjectFarm]

Thank you very much!

[@HyakuJuu01300]

Experience is the best teacher after all.

[@ac.creations]

Knowledge is not a substitute for wisdom.

[@marksierra3522]

@@ac.creations You know what a deepity is?

[@DrYosh2]

@@marksierra3522 they probably have no idea. Here's the cliff notes: Knowledge and wisdom aren't a "this vs that" situation. Wisdom is applied knowledge. You can't have wisdom without knowledge. And misapplication of knowledge isn't wisdom.

[@goonaba1016]

You should try cutting fluid as engine oil, since it seems to have a smaller wear scar than regular engine oil

[@bradley3549]

I was thinking the same thing!

[@ProjectFarm]

Great recommendation!

[@savoryflan]

I was thinking the same. Maybe use a mix of 75% engine oil and 25% cutting fluid.

[@Vectorous]

Yeah. I want to see this.

[@stephenshivery2531]

definatley agree would make a good video and could put all that extra cutting oil to good content use!!

[@leonhaku]

I have no clue why im watching these as I'm probably never going to be in a position to be criticizing cutting fluids but goddam, it almost feels like watching a horse race and am hoping a specific brand wins. The production value and scientific approach to these tests absolutely make me cling to my seat as he's super methodical about testing these products' every aspect. Anyone can make these vids but the superb commentary makes me wanna come back and watch another. Great job PF!

[@ProjectFarm]

Thanks so much!

[@MattCayen]

@@ProjectFarm Feel ya, I had the answers I was looking for and kept watching..

[@SilverC8andDroppedC10]

Picked up some Tap Magic after watching this video. I needed to drill a bunch of holes in my truck frame and the instructions for the part I installed stated I would go through several drill bits. I purchased the bits PF recommended in the best drill bit video and completed the entire job using tap Magic & a single bit. Thank you Project Farm. Todd, you are the absolute best!

[@ProjectFarm]

You are welcome! Thanks for sharing.

[@Mmouse_]

The gymnastics some American companies do to avoid saying "made in China" is amazing.

[@ParkerUAS]

That comment was made by, or under the supervisory control of, Max Mouse.

[@BAMAJiPS]

You'll note that most companies that say "Made in USA with global components" (or "proudly made...") usually have stickers all over the box and product saying such (DeWalt comes to mind). You can take it to the bank that every major component was made elsewhere and they MAY have assembled those components here in USA, but more than likely the made in part refers to someone putting a sticker that says as much and maybe combining a part or two and boxing it all to be able to SAY "Made in USA" Its really sad in my opinion

[@dantethunderstone2118]

Max Mouse assembled in USA with international components aka made in China label applied in the states

[@ParkerUAS]

@@dantethunderstone2118 , more like assembled in the US out of Chinese parts.

[@Senkino5o]

@@BAMAJiPS I got a couple of Empire 2' levels the other day, one is digital. One of the reasons I got them is cause the box said made in USA. After buying I had a look and only the vials are made in the USA, all the edge milling and assembly is done in Vietnam.

[@ckl8a]

my dad is a machinist and he swears by tap magic. I always just took his word, but it's good to see he knows his stuff!

[@RadDadisRad]

It doesn’t hurt that it smells nice too

[@rayraden2527]

ckl8a I use tap magic I’v been using it for about 20 years good stuff

[@cavemaneca]

Yeah, I'd just assumed from experience that Tap Magic was the best, but it's nice to see a good comparison showing how well it works.

[@ThePapaOfThree]

When you say "we're gonna test that!" It gives me chills ;-)

[@ProjectFarm]

Sorry to hear!

[@ThePapaOfThree]

@@ProjectFarm I meant that as a compliment. I love when you say that. Please keep finding things to test. I've watched nearly all of your videos and learned SO much

[@bobd.]

That may be true (you getting chills), but I bet the manufacturers do too. 😁

[@donqpaul5551]

Needs to be on a Tshirt or I need to be directed to the store that sells it.

[@colevandervort4962]

Respect how much time and effort this guy put into these videos, and does not even have a sponsor.

[@johnd9357]

This is literally the only channel that I insta-like every video. I don’t even need to watch the video to know it’s good. If it’s project farm, it’s quality. Never change man, keep this formula PLEASE! I get so worried that you’re gonna blow up and change something upon the behest of others, and lose the magic. These videos are gold the way they are!

[@ProjectFarm]

Wow, thank you!

[@jackhanson8467]

@@ProjectFarm He's right you know. I do exactly the same, hit the Like button as it starts, every time. You never disappoint.

[@willnotcomply1328]

I hit the like before watching too....

[@davidscott5903]

He's right.

[@Random_4400]

Same here!

[@Haywoodjablomie100]

Pretty embarrassing for a company to develop a product, spend money on R&D, product packaging, marketing etc and it gets beat by bacon grease lol. Thanks so much for the video!

[@loosewirewire7954]

What's worse is when they put all the money into hype, packaging and advertisement gimmicks and not R&D like they are supposed to. As long as it sells and makes a big enough profit they don't change the effectiveness. The money goes to cost cutting measures in manufacturing instead of research in how to make it better with the new technologies. But we fall for it and they make money so it's hard to blame the business midel which is why channels like this one is so wonderful and important!

[@ancientapparition1638]

@@loosewirewire7954 Yep at the end of the day corporations exist to meet one goal - make money.

[@CaptainDangeax]

Maybe they should have tried bacon grease in their lab as well, as an average control product

[@mikevlek]

Well to produce 500ml of bacon you need to cook about 1000g of bacon so all the developing is invested into those kinds of things. But hey if you want to cook 1kg of bacon instead of buying a 10$ bottle thats fine XD

[@mjc0961]

@@mikevlek Of course I want to cook bacon instead. Then I have bacon to eat. 🥓🤤

[@Gum05]

As a retired toolmaker, we swore by TapMagic even though we had no scientific data supporting that decision. We did use paste wax for finish machining/grinding on mild steel and aluminum with good results. Great video as usual! Keep up the great work!

[@ProjectFarm]

Thanks, will do! Thanks for sharing.

[@garbo8962]

I use to do a lot of electrical work in a tool & die shop. Firemen told me that Tap Magic works great but too expensive for them to use everyday. Have some cans of the earlier Tap Magic version that they changed back in the 1980's. It evaporated quickly and keep the tap cool.

[@shawnchong5196]

Project Farm - you're tests are so good, and I like how your commentary, testing, video and sound all improved with time. So much kudos to you. I hope you can stay unbiased moving forward. This channel is basically consumer reports, but you show the testing, teaching us people how the pros do it! it's awesome!

[@ProjectFarm]

Thank you very much!

[@combatmedic1980]

I'm really surprised you didn't include WD-40, since I see a LOT of people use it to drill with.

[@HemiRod23]

WD-40 is particularly good when cutting or drilling aluminum. It helps keep the cutting tool from loading up.

[@mattnewberry3980]

I would like to see WD-40 tested too!

[@liamstrong5223]

WD-40, a terrible lubricant, okay cleaner, decent water displacer, and brilliant aluminum cutting fluid

[@blackbirdxx928]

It's works fine...it just takes a lot...it works because it's not a lubricant....lubrication it the keep metal parts from touching.. So the bit needs to burn off the lube before it can cut....I have best luck with atf.

[@slipsonic809]

@@liamstrong5223 dont forget wasp killer. WD-40 kills yellowjackets in about 5 seconds, and if you use the spray straw you can shoot em down while they're flying like little fighter planes.

[@TheConjurersTower]

At first I was going to ask why you had armor plating laying around, then I remembered it's 2020 and you're probably just turning your tractor into a tank so you're ready for the alien invasion in November.

[@ProjectFarm]

Thanks for sharing.

[@dposcuro]

@@ProjectFarm the non-commital answer. Wise, very wise.

[@adriananderson1258]

@The Conjurer's Tower what's happening in November?

[@TheConjurersTower]

@@adriananderson1258 It's a joke, so many relatively wild things have happened this year (pandemic, riots, some close-call international conflicts) that an alien invasion would fit right in and barely even be a surprise. I think there's a meme template somewhere with each month's 'event' for the year, iirc the aliens arrive just before the meteor impact or something.

[@saccaed]

Queue mad lad intro music...

[@hansulrichjohner2694]

This test would be very interesting on stainless steel! This is the hardest metal to machine I have ever seen, but here the cutting oil may be crucial.

[@ProjectFarm]

Great suggestion! Thank you.

[@SP-ls8lw]

​@@ProjectFarm Tap Magic makes an "Xtra thick" with higher sulphur content for harder to machine metals like stainless.

[@thewildbean4413]

I love how fair the testing is on this channel

[@ProjectFarm]

Thanks!

[@bcgrittner]

When I worked at the store I sold drill bits by the dozens, but not much cutting oil. Your video should make a believer out of anyone.

[@ProjectFarm]

Thank you very much! I didn't realize it made such a huge difference.

[@danhillman4523]

Even if nothing else is available I will put a few drops of motor oil when I drill any type of metal.

[@danhard8440]

i have a mom and pop small hardware store next to me and i talk to the guys there about your channel all the time and now they watch also so that they can better advise there customers and help there business

[@ProjectFarm]

Fantastic! Thanks for sharing.

[@thewolfin]

their* business

[@ducatiist]

@@thewolfin chill out - what are you the KZbin spellcheck? We define language, it doesn't define us. If you can understand him then you know what he meant.

[@charlesangell_bulmtl]

@@ducatiist LOL

[@hugolafhugolaf]

ducatiist Being satisfied with the lowest common denominator gets you nowhere.

[@CodelGeass]

THANK YOU PROJECT FARM! Another question that I have had for years answered! Appreciate all the time, effort, and hard wirk that goes into every video!

[@ProjectFarm]

You are welcome!

[@jackalninezeronine]

I love his sense of humor, best tool channel there is.

[@ProjectFarm]

Thanks! Great to hear!

[@noahellice2184]

I love this guy, he goes through so much to make test as accurate as possible

[@ProjectFarm]

Thank you very much!

[@Bob_Adkins]

Some of the popular testers say "I think this one is best because it's best for me". PF's tests are useful to everyone, not just the tester. We're so lucky to have him.

[@stupaod]

My only complaint(mostly) is that he only runs the tests once. Three tests would increase the accuracy quite a bit and help weed out possible unknown influences that could affect the results.

[@Bob_Adkins]

@@stupaod And triple the work and expense, and it would no longer be fun.

[@Darninja99]

@@stupaod I think for the purpose of this channel it would be almost redundant. I see your point and agree with it, although I think Todd sets his tests up in a way that's precise enough to avoid repeating them. After all, it's not like he needs very accurate data :)

[@tomjones4318]

Oh, the smell of Tap Magic at three in the mourning. Bringing back memories.

[@ProjectFarm]

Thanks for sharing.

[@evanvokes1694]

Would the mourning be as a result of a broken tap. We have not had an effective tapping compound since 1.1.1 tricholoethane. Cutting the new rapid tap with 5%acetone is OK but its still awful

[@bloccoaspirale1867]

I'm sorry for your loss.

[@IceAgeSquirrel2008]

I really struggle for the best words to express how grateful I am for your videos. At any rate, thank you!

[@ProjectFarm]

Thanks and you are welcome!

[@felixsantoyo6909]

I was an automotive tech for many years. We were usually told by the tool dealers to use transmission fluid as cutting oil. Can you test it against some of the products used in this video? Love your channel

[@ProjectFarm]

Thanks for the video idea.

[@919hornet4me]

Yes, I would also like to see transmission fluid tested

[@johnstorrie3635]

Also include rear axle / hypoid ep fluids.

[@mw3gamer23]

I always used wd40 or silicon spray

[@alantownsend5468]

I'd also like to see hypoid gear oil and trans fluid put up against the winners from this video

[@nemo227]

Project Farm videos are VERY useful and the speed of the narration is good (won't put you to sleep).

[@ProjectFarm]

Thank you very much!

[@intillex1]

I think it's pretty clear we need to see how cutting fluid works as a motor oil!

[@ProjectFarm]

Great suggestion!

[@LawpickingLocksmith]

With such low wear we need Matt from Warped Perception to bring a bottle on NOX along and then boys will be boys till an engine blows up.

[@vikmanphotography7984]

I haven't done any machining in years and I'm not likely to return to it with any regularity but I do appreciate the effort you go to to isolate variables, considering the wide range and quantity of test setups you build.

[@ProjectFarm]

I appreciate that!

[@ChevyRedneckGFX]

What do you do instead of machining? Trying to get out

[@wilsonrawlin8547]

Been using Tap magic for 14yrs, Good stuff. Yes, I have to drill a crap ton of armor as well. Project is my gold mine of learning what is best and has save me countless times.

[@TheNickLavender]

We literally sat down with our food a min until 5, hit refresh, there's the new vid, and we are good to go lol!

[@ProjectFarm]

Hope you enjoy the food and video!

[@bolech5221]

I can just imagine 3 guys sitting on tilted chairs eating pizza in a dark room and hitting f5

[@marty3469]

All they need to do is mix CRC with bacon grease and there's the winner, does the job and smells great at the same time 👍

[@TheTyisawesome]

Lol awesome man!

[@Fister_of_Muppets]

I wonder how well some of those cutting fluids would work as an "emergency" motor oil...

[@ProjectFarm]

Thanks for the video idea.

[@TheRedstar91]

I think a lot of the anti-wear additives in cutting fluid are based on sulphur. Be careful about the exhaust gasses is my tip. Other than that, it should work quite good.

[@wallacegrommet9343]

Low sulphur diesel now contains biodiesel (soy methyl ester) in many markets as a lubricity improver. And the diesel fuel really needs it for people running older mechanically governed Diesel engines. The EPA lowered the fuel lubricity standard to meet the ultra low sulfur goal.

[@highstreetkillers4377]

Gundrill oil please if you do that. Gundrill oil is a magical oil that would be very interesting in an engine because it might be far superior

[@sandorpecsora2434]

I had the same first thought, so upvoting your comment and hoping for the best :)

[@hootinouts]

Your tests and videos are always top notch and very informative to folks like me who are always fixing things and making chips out in the shop. When I was in tool and die making, we use to dab lard oil on the drills and end mills using acid brushes. It smoked and had a bit of an odor but did a great job of helping the cut. Thank you for doing what you do and for sharing with us all.

[@ProjectFarm]

Thanks and you are welcome!

[@coolfouad74]

Greetings from Lebanon, I've been watching your very impressive tests for quite a few weeks. I've seen many of them, but for me this one has just stood out, just because you're speaking a bit slower than your usual pace. I'd like to suggest that you test the "Knipex Forged Wire Stripper 20-10 AWG" 13 72 8 along with similar tools from other brands if possible, and I'd love to see it at the same pace as this one if you don't mind. Thanks for the time, commitment, hard work, and most of all - for the making your tests as scientific as possible. Cheers :)

[@ProjectFarm]

Thanks and you are welcome! Thanks or the suggestion.

[@clem2usa]

I was really concerned that the shortening may have gluten, thanks for clearing that up! 😂

[@ProjectFarm]

Happy to help! lol

[@dennisyoung4631]

Fats *tend* to be gluten-free…

[@Mr_Sleaze]

I want to paint my exhuast. I'd like to see a comparison of high heat paints.

[@ProjectFarm]

Thanks for the video idea.

[@RenaxTM91]

None work good over time, thats my experience atleast, and I've tried a few and seen a few more... The combination of really high heat during many cycles, exposure to water when hot etc makes it really hard to do.. Ceramic coating is the only thing that holds up over time, and even that struggles near the turbo's...

[@TEAMWRIGHTEOUS]

Titanium exhaust is the way to go.

[@ChemicalU235]

That is a very good idea

[@stevehertz4878]

I have found when it comes 2 engineering a clean surface 4 1. Then a good coat let it dry 4 a day then again.and works really well. I use plaid coat.

[@rh5971]

Pretty slick video! Thanks for another great product test and review.

[@ProjectFarm]

You are welcome!

[@The1withlogic]

“We’re going to test that” I smile every time you say that.

[@ProjectFarm]

Thanks for sharing.

[@Thesignalpath]

You have a methodical, vigorous and thorough style of investigation. Thank you, it is a pleasure to watch your videos.

[@ProjectFarm]

Thanks so much!

[@erich3784]

Man, I was JUST thinking about you, like "hmmm I could really do with a Project Farm video right now" and Bam! Man you're the best haha

[@ProjectFarm]

Wow, thanks! Happy Monday!

[@user-tf7hf8jp7p]

@@ProjectFarm actually, its tuesday already🙂or wait a minute, here finland its tuesday alr still.

[@Erik_Swiger]

Things you do, like the closeup views of the edges of the drill bits, magnified, and tracing back and forth with a pointer - stuff like this adds tremendously to your videos. I mention this because it comes and goes so fast, yet I realize what it takes to make those shots. I notice these things because I want to make my own videos, so I don't just watch your videos, I watch how you make them.

[@ProjectFarm]

Thanks 👍

[@robertmitchell8347]

Amazing work on these videos. Trully greatefull and entertained. I'm not very experianced in this area and now am totaly impressed what good cutting fluids can do without fancy flowing systems.

[@Liamtronix]

I really like this format where you run all the tests on one product, then all the tests on the next product, etc. I find it's more enjoyable than running all the products through one type of test, then all through the next test...

[@sandman_-_]

probably the highest quality content i've seen in years. so much planning and effort goes into this that it shines through with brilliance!

[@ProjectFarm]

Thanks so much!

[@chrisbarham5373]

Isn't he awesome

[@WideAwakeHuman]

He's a one man Consumer Reports team that's free on KZbin and actually has unbiased tests... Lol. Top 5 channels for sure

[@Firemedic2105]

Thank you! I love that you have the most honest and transparent testing around!

[@ProjectFarm]

Thanks and you are welcome!

[@voodoochild1954]

Great video as all of yours are. I been using Tap Magic for over 40 years now and was thinking maybe there was something better made these days. After this I think I’ll just stay with Tap Magic and know that it’s better than the rest. Thank you!

[@ha-y-in6938]

Now finally it has been found, BACON goes with everything. Proven.

[@StarlightWorkshop0z]

Except the people that came from the sand and like their woman wrapped up

[@hksp]

not for the aloha snackbar lover

[@wagonator6891]

@@StarlightWorkshop0z Works excellent as a repellent.

[@StarlightWorkshop0z]

@@wagonator6891 bacon could be the meaning of life

[@ducewags]

@@StarlightWorkshop0z Bacon IS the meaning of life. BACON.

[@Dirty_Bits]

When building out a prototyping machine shop at a previous employer, I tested a variety of cutting fluids, and Tap Magic came out on top. We used to buy it by the gallon and use it in misting systems on all of the equipment. Tool life was phenominal. Glad to see that you found similar results.

[@rrvette7953]

Again Project Farm does another awesome job testing products. THANK YOU..

[@ProjectFarm]

You are welcome!

[@Welwynnick]

Fantastic video as always. If only all KZbinrs could get this much into a video! Many thanks, Nick

[@ProjectFarm]

Thanks so much!

[@O.D.B.420]

I love how you are fair on all your evaluations. Same weight on drilling, using timers, just every test you do is fair to all the things being tested and minimal human error or human influence in the tests. Great work.

[@RedBeardOps]

Dude... thanks a million for this! Ask and you deliver! You're fast!

[@ProjectFarm]

Thank you very much for requesting this one! 100% of the videos on this channel are viewer requested.

[@PovlKvols]

As always an excellent test from the one man testing center. You're amazing!

[@ProjectFarm]

Thanks and you are welcome!

[@CALDues]

Nailed it! Thanks for your time and dedication.

[@ProjectFarm]

You are welcome!

[@kenball1980]

I never knew cutting fluid actually speeds up drilling times. I'm going to start using it all the time, probably CRC or 3 in 1 in a pinch.

[@evanvokes1694]

Nothing really works once they got rid of 1.1.1 tricholoethane in rapid tap. Cutting with the new rapid tap with 5% acetone works better than anything that was presented but its still useless by way of comparison. Relton should have fought this as it has created far more environmental damage by not having it than the small amount of tricholo damage from use. Its not like there were millions of gallons of it made

[@tymz-r-achangin]

My dad has worked at Timet Metals as a machinist for 0ver 40 years. They manufacture rolls of titanium for companies such a Boeing, and Tap Magic is one of their top cutting fluids used. They also have special cutting fluids specifically made for them when having to machine titanium.

[@ProjectFarm]

Thanks for sharing.

[@unclemarksdiyauto]

Great video and nice to see real results as your videos always do!

[@ProjectFarm]

Thank you!

[@JohnDoe-pv2iu]

I knew the outcome of this when I saw the title. I have been using Tap magic, recommended by a firearms engraver for it's super slick properties for All cutting tools... I have used it for about 30 years and it is the Best, hands down! I have also tried nearly everything and nothing comes close to this stuff. Other items might help cutting kinda close but NOTHING comes close to Tap Magic for taking Care of and protecting expensive cutting bits. Great video! Take Care and be safe, John

[@ProjectFarm]

Thanks so much!

[@KingAdrock420]

You almost made me shoot Coca-cola out my nose when you started listing off the fat content of the shortening. But for a request, how about a video testing studfinders?

[@Ronsonic]

That was my request yesterday. Buying a new house and will be doing a fair bit of work.

[@DorianM222]

And to also test the live wire detection in concrete and other types of walls. It never really works for me.

[@PhaedruS007]

Stud finders! Good one. I have many unnecessary holes in my drywall. I recently needed to hang something on an exterior wall covered in Stucco. I didn't even try my stupid studfinders on it.

[@robholmes2129]

@@Ronsonic Dewalt and Milwaukee both offer wall scanners that show everything inside a wall,electric,plumbing and studs

[@hailster]

This is a great idea, I've used some pretty crappy name brand stud finders and some unknown Chinese brands that were awesome stud finders. I think this would be a great video to watch.

[@davidr6585]

Excellent! You keep setting the bar higher.

[@ProjectFarm]

Thanks!

[@donqpaul5551]

I love that we get a serious challenge on cutting oils with a fun bacon grease thrown in the mix. Fun and Educational.

[@ProjectFarm]

Thanks!

[@electronicsNmore]

I'm always drilling through steel plates when working on projects. Now I know what to buy, thanks to your outstanding tests! 👍

[@ProjectFarm]

Glad to help!

[@Laffen47]

I've not watched it yet, but I'm hoping it's great value shortening

[@SilmarilS79]

@Hydin Biden You realize that most press drill beds are made with a hole in the center just for that!!!

[@dariuszskiba8113]

For the first time in my life I have actually used the knowledge from the YT channel in real life situation.

[@ProjectFarm]

Glad to hear! Thanks for watching.

[@RickaramaTrama-lc1ys]

I was so glad to see at this time you have almost a million and a half subs~! This is another one of your videos that explains what I have been wondering about for over 50 yrs.~! Where else on Earth could we get these kind of comparisons~? You might not realize it but you have become something of a Scientist that we all have access to for all our questions about things we never knew but thought we did. Much Respect~!

[@ProjectFarm]

Thanks so much!

[@seanwolfe9321]

Wow! That was VERY informative! You gained a new subscriber just from this one video. Nice job!

[@ProjectFarm]

Thanks for watching and subscribing!

[@berlinetta350]

I guess I'll be using tap magic in my diesel motor from now on.

[@MicahS70T5M]

Berlinetta I think you'd probably junk your engine. even though it might be better at lubricating, I'd be concerned about the hundreds of heat cycles your engine will experience in the time between oil changes.

[@krASHExxx]

Ahahaha good one

[@Jack-bv5xd]

Micah N. r/whoosh

[@jamesfrench7299]

Bacon grease would be great for drilling in the morning, and personal lube for "night drilling" 😂.

[@Promethium666]

Mmm bacon creampie, yum.

[@henrymatthews9365]

Wow I think I saw that once on RT

[@earlcousins6635]

Really enjoyed the info. GREAT JOB!

[@ProjectFarm]

Glad you enjoyed it!

[@thereeljahjah]

BRO!! BRO!! Wicked review!! I recently bought the deWalt Step Bit you reviewed and I hadn’t yet seen this older review.. it so happens by accident I also bought Tap Magic… WHAT A COMBINATION!!! RESPECT IS DUE TO YOU SIR!! 👊🏼👊🏼

[@ProjectFarm]

Thanks!

[@oledcrt]

I’m blown away by some of those tiny wear scars on the lubricity tester. I wonder how well RapidTap would work as engine oil? ;)

[@greatdaneacdc]

Be a expensive oil change !

[@evanvokes1694]

Film strength on a plain bearing is not the same as how a tapping/cutting agent works.

[@Erik_Swiger]

He should run engines using cutting oils! Would be a great competition!

[@bagelbandit6076]

Or a 50/50 mix lol

[@spankey0069]

Best me to this comment

[@johnossendorf9979]

Tap magic was all ways the cutting oil of choice in my father's steel fabrication shop.

[@sonofTMHYAH]

Just an awesome, well put together review!

[@ProjectFarm]

Thank you kindly!

[@tropicalspeedbmw]

Great video! Thanks PF!

[@ProjectFarm]

You are welcome!

[@LBCBassKings]

Oooohhh, THOSE kind of drilling lube.

[@ProjectFarm]

Thanks for watching.

[@DMalek]

@@ProjectFarm Not even a BOT can answer that well to that comment :P

[@ripnsoar]

😂😂🥴🤙🏻

[@wls64]

LOL!

[@igorbarbarossa]

07:30 lol, that's what I look for when buying cutting oil

[@ProjectFarm]

lol Thanks for watching.

[@martyb3783]

Great video! Another amazing learning experience. I don't know how I missed this one until now. Thanks a bunch!

[@ProjectFarm]

Thanks! Glad to hear!

[@davehoward2791]

Been using 3-in-1 and WD-40 for decades for drilling and cutting threads (when I used anything at all) and have always been satisfied. But now that I'm older and tired of trashing good drill bits and taps & dies (especially when using nothing) I just ordered a big bottle of Tap Magic EP-Xtra after watching your video. Your videos have directly influenced at least a dozen of my purchases over the last year or so on numerous items, and I am grateful for all of the hard work and unbiased information you provide your viewers. Many thanks and please keep up the fine work, it is appreciated by many! 👍

[@ProjectFarm]

Thanks, will do!

[@Zuuby]

Dang, that was nearly 15 minutes long? Not once did I get impatient or check the time remaining in the video. I was completely absorbed and lost track of time, similar to dreaming. What is this sorcery?! 👍

[@ProjectFarm]

lol Thanks for watching.

[@SonicBoone56]

I just get sad when the video actually ends lol

[@DoctorPrepperMD]

As a man that quit high school, ended up with a physics degree and a medical degree, now returning to the trades I find you videos awesome. You understand and do an amazing job of scientifically evaluating comparisons and at the same time being real!!!

[@ProjectFarm]

Thanks so much!

[@markhull1366]

Wow, that's an amazing story. Would you consider making a video on how all that came about and post it on YT? It sounds like a very interesting story that would be very inspirational.

[@dtj9923]

You consistently put out some of the most entertaining and useful content on KZbin. Your comparisons are really great. I love the garage test lab equipment, and of course bacon grease whenever you can test it! I typically use one of the two different versions of TapMagic depending on my application. The thick sticky version is great when you need the fluid to stick to something like a tap or you're loading it up into the flutes of a drill. The thin version is good all around if you aren't running coolant or a Kool-Mist unit. Loading it up on a chip brush and using it to keep turned or milled surfaces wet really improves cutting speed, tool life and surface finish. I also keep it in a pump oiler for shooting into holes especially when drilling or boring on a lathe. Definitely my go to cutting fluid.

[@ProjectFarm]

Thanks! Thanks for the feedback.

[@ndungukaberere8477]

This was definitely a good video, the idea & execution is simply superb. I like your scientific approach to this & for that I've subscribed to see more of your content in future.

[@ProjectFarm]

Thanks for watching and subscribing!

[@GoblinKnightLeo]

I've only ever used Tap Magic. These results were really interesting!

[@ProjectFarm]

Thanks so much!

[@dpt4402]

Same here, the small 4 oz cans are handy when your work involves the use of an extension ladder.

[@dougberrett8094]

I have used Tap Magic since 1970, but only to tap. Mostly with power tapping heads that tap much faster than hand tapping. Don’t use other stuff.

[@paulkolodner2445]

Same here. But you have to admit that bacon grease has the clear aroma advantage.

[@blackbirdxx928]

Tap magic,? It's not called drill magic? Must be a reason..lol

[@jacobstephens6937]

Genuinely one of the best scientific-but also practical-shop product testing channels out there. Anybody can see how much thought, prep, work, and analysis goes into these videos. There’s never a video from Project Farm where I find myself wanting to click away before the video ends. Great work. I’ll see you on Patreon

[@ProjectFarm]

Thanks for watching.

[@GYccUsefultips]

Top notch you tuber..Gluten free..Organic and proudly made in the U.S.A with imported materials...lol...You're the best brother..The world thanks you...Ppl love you brother

[@ProjectFarm]

I appreciate that! Thanks!

[@chuck1607]

I am in the market to purchase cutting oil. Thanks to your video my decision was quickly narrowed down to CLI & Tap Magic. Thank you for taking the time and effort to do this video.

[@ProjectFarm]

Thanks and you are welcome!

[@TheRCBasher69420]

Who thinks that he should try rapid tap as engine oil

[@TBPony]

yeah seriously the super low wear marks on the bearing is very interesting, like a full oil and heat analysis would be fun to watch compared to a good synthetic motor oil or like an oil additive

[@darkfur18]

Absolutely this, It would be neat to see how it compares

[@nashsimon8120]

I agree

[@justmetal227]

This

[@AndrewHowe_Is_Really_Neat]

Was about to come down and comment this myself, I think it'd be neat if he did all others the ones with a small wear scar as well.

[@iteerrex8166]

I would've liked to have seen the humble mineral oil.

[@MrTheHillfolk]

And water ... I've been using water with like 5% soap from a squirt bottle on the band saw lately,and it seems to make a nicer cut, probably because you can flood it heavy and keep it cool.

[@deltastvyt]

And WD-40

[@Dial8Transmition]

I use wd40 and was hoping he would include that :P

[@HadToChangeMyName_YoutubeSucks]

@@treyhart6861 -- I ran out of cutting oil just this weekend, thought I'd give wd-40 a shot since I had some handy. Just wasted my wd-40 as far as I could tell. It did boil off quickly so I expect it cooled things pretty well just by boiling off, but it didn't seem to provide any lubrication. That said, lots of people swear by it, so who am I going to believe, lot's of strangers on youtube or my lying eyes?

[@Bob_Adkins]

@@HadToChangeMyName_KZbinSucks I've only found it useful as a cleaner to remove oily scum. It's about as effective as paint thinner, but smells better. Drilling-tapping-cutting? Zero effectiveness.

[@davefoc]

Non machinist here that has always been skeptical of the idea that cutting oils help all that much. I just didn't understand how they could work. I still don't understand how they work but now I'm sure they do work. Thank you.

[@ProjectFarm]

You are welcome!

[@NorfKhazad]

Glad to see my preference for tap magic vindicated! Great video as always.

[@ProjectFarm]

Thanks so much!

[@highnoon9333]

it's amazing how you devise all of these tests. That bearing wear test is so cool

[@ProjectFarm]

Thanks for watching.

[@alistairunie1710]

Would love to see a Behind the Scenes style video. Maybe showing how much raw footage you have to look through and edit, camera setups, how you started out, how much effort you have to do shopping for all the goods, and bloopers lol idk I am just spit balling ideas! I love the channel, its borderline theraputic watching and listening to you work away! Keep the videos coming!!

[@ProjectFarm]

Thanks for the suggestion.

[@RickaramaTrama-lc1ys]

I second that emotion~!! (borrowed from Smoky)

[@BSAElectronics2014]

Great video and testing method, I just found your channel, you have earned a new sub! I just ordered the Tap Magic fluid

[@ProjectFarm]

Thanks and you are welcome! Thanks for watching and subscribing!

[@Anonymous-it5jw]

Great test! Next time, the test might have a more level playing field, if any solid greases, like bacon grease and solidified shortening, were heated enough to liquefy them before application, so that they would flow and have surface tension like the other lubricants in the test. I think that most people with regular shop tools and a need to drill plate steel would gladly take a minute or so to liquify the grease, if only to avoid ruining their expensive drill bits. For a future test, consider testing oils or liquid oil additives that contain Molybdenum or some similar wear additive, such as the OEM and other oil additives for limited slip differentials. Thanks again for your unbiased service to farmers, DIYers, hand & power tool users of every description, including mechanics everywhere, especially those in small places like Avoca NY, Staten Island NY, Pine Hollow PA and Rocky Tops everywhere.

[@bigj1718]

Since July 4th is coming up I was wondering if you could do a video on some charcoal and some other things related to grill outs like brushes and temp gauges. Other than that great video!

[@ProjectFarm]

Great suggestion!

[@thorwaldjohanson2526]

lots of pressed brickets contain a large portion of sand and dirt as cheap additives. Could be interesting to see, if there is a 'good' bricket brand out there. You can judge the quality by the amount of ash left

[@tinncan]

Agree, it would be great to follow up on the AvE ash video.

[@virtualtools_3021]

@@thorwaldjohanson2526 Try lump charcoal, i use a heat gun to get it going fast!

[@bigj1718]

@@thorwaldjohanson2526 yeah and like charcoal alternatives made of wood

[@mtlefty8687]

I'm absolutely hooked on your videos. Always looking forward to your next one. Would love to see a comparison on gas powered wood chipper/shredders for the average home owner.

[@Chris-sx3he]

I'm always amazed at you're videos. Well done.

[@ProjectFarm]

Thank you very much!

[@rustynail8005]

Another awesome video great job!! 👏

[@ProjectFarm]

Thanks so much!