Changing crankshaft seals on a STIHL MS211/C chainsaw. Donations accepted at: youshouldbuildit.blogspot.com... Blueprints available at: youshouldbuildit.blogspot.com...
Пікірлер: 120
@jeffcamp4816 жыл бұрын
To remove flywheel, position a punch on center of shaft, after removing flywheel nut. Strike punch with hammer, the shock will loosen flywheel. Remove by hand.
@daphlavor5 ай бұрын
You’ve given me more courage to tackle my ms250, which needs a new piston & cylinder, great info on the visuals especially the sealant at the bottom!
@dbaker32646 жыл бұрын
Light coat of RTV in the seal channels of the case both side needed as well. Hence casing seal and bearing channels are part of the molding, not a milled process to make sure they are perfectly round, so the light coat of RTV is needed in the seal case channels so the outside of the seals get fully seal to the case channels as well.
@Mike-tg8gl7 жыл бұрын
I enjoy watching your videos.
@DonnDIY7 жыл бұрын
Thanks, buddy!
@geedubb20057 жыл бұрын
another awesome project Donn!
@DonnDIY7 жыл бұрын
Thank you, Gee!
@timsturgill36175 жыл бұрын
We do repairs on chainsaws & I learned from this video
@phillipkramer18977 жыл бұрын
Did you dirco the outside flanges of the seals and grease the insides? I also was surprised to see you didn't use a feeler to gap the coil.
@tm1717173 жыл бұрын
Great video, thanks.
@moeenahmed68539 ай бұрын
Hi. Where did you get the sealant from and what is the brand called??? Can you use any sealant which is heat resistant?
@claudiocorigliano84937 ай бұрын
Ciao, interessa anche a me questa informazione
@Antonio-pd7tn5 жыл бұрын
Неплохая бытовая пила , мягкие амортизаторы , приятная работа двигателя . В хозяйстве с 2008 года .
@marcb88746 жыл бұрын
THANK YOU FOR THIS video but you change the segments, and the grooves on the cilyndre what do you do? I ALSO SEE BEARINGS open without grease? I AM TR7S SURPRIS are they greased by the oil of the mixture?
@robertstroh48034 жыл бұрын
Yes the oil in gas lubes bearings .if you think about it kinda amazing that they don't burn up
@danhenderson7837 жыл бұрын
The flywheel pops right off with a slight pry to the backside while tapping the loosened flywheel nut. Don't drill Hiles into it!!!! It is precisely balanced.
@crankshaft10534 жыл бұрын
Dan Henderson I just tap the crank with a hammer
@BobChanter3 ай бұрын
Was balanced. Not anymore.
@Wcf-qn9ip4 ай бұрын
Great video. Thanks
@ciftsarili3 жыл бұрын
Nice job👍
@jacoblang27125 жыл бұрын
I just love my 021
@KentuckyFriedFixes2 жыл бұрын
This is a great video. I can see why its gotten over a quarter million views. Good stuff.
@roystheboy3 жыл бұрын
I had a customer that replaced hes own crank case and piston rings but engine fires but wont run unless I'm holding the throttle in and cuts out even when the throttle adjustment is on full, I did a compression test only showing just over 25 carb has been cleaned this one has got me
@neddy1287 Жыл бұрын
Well the compression should be well over 125 psi but you mentioned 25psi usually means there's air leak somewhere on the engine. Or worse case the cylinder head, piston and rings are shot. To get compression to come back you would have to clean the bore with two stroke oil and a lint free cloth, clean the piston ring gaps for crud buildup and clean the rings as it needs to be moving. I have heard of sticky rings stuck to the piston resulting extremely low compression or holding the pull cord letting the chainsaw free falling on it own as signs of dropping too quick is lack of compression. That all I can think of due to my brother asking me 101 questions of why it not working for him
@perkypat22146 жыл бұрын
How did you stop the crankshaft from turning when you loosened the flywheel nut?
@gonkeyhughes3 жыл бұрын
I put parra cord in top of cylinder through the spark plug hole about. 2 foot leave a bit hanging out and it traps piston on the head. After undoing the nut pull cord out easy
@lildonkey2926 жыл бұрын
you should get a flywheel puller and crank case splitter . they make life alot easier
@BobChanter3 ай бұрын
A crankcase puller is not needed in this job.
@johnclarke66477 жыл бұрын
just screw the flywheel nut on the shift a few turns and hit the nut with a small hammer, sharply, and the flywheel will usually come off the shift. if not try a BFH.
@AFHProjects7 жыл бұрын
Good work! :)
@DonnDIY7 жыл бұрын
Cheers!
@clearlakebunch8569 Жыл бұрын
Excellent very helpful I have question on Seals my old seals are ones brown the other is blue Why// why are they called soft seals and hard seals and if they are different which one goes where??
@AndrewBrowner6 жыл бұрын
i assume the flywheel only goes on the crankshaft one way so theres no timing settings as long as those two parts are bolted together the sparks timed properly?
@DonnDIY6 жыл бұрын
Yes, it goes on only one way.
@Adam-xs3ng7 жыл бұрын
good video, really clear video with good focus, what camera do you use¿
@DonnDIY7 жыл бұрын
Nikon Coolpix.
@dstevenpaisley7 жыл бұрын
I have a 034 that's going to need seals .flip it to cut a tree runs like hell works all right blocking wood.How long did it take you to do? I know the 034 is way different than that saw but gives me a idea!
@DonnDIY7 жыл бұрын
It took me a whole day basically. If I had known in the first place it needed new seals it would've taken less time.
@AYALARAMON1006 жыл бұрын
Nice video
@same90906 жыл бұрын
very good video
@DonnDIY6 жыл бұрын
Cheers!
@musurmonergashov12983 жыл бұрын
Good job nice
@phillipkramer18976 жыл бұрын
I hope you cleaned out the exhaust port at top dead center
@mimiporsche7 жыл бұрын
Bravo you have replaced the crankshaft oil seals! The ball bearings were good?
@DonnDIY7 жыл бұрын
Bearings were good.
@wojciechostrowski36867 жыл бұрын
fajny film
@dejan97136 жыл бұрын
How long you wait usually after aplications of gasket sealer?
@DonnDIY6 жыл бұрын
24 hours is usually said on the sealer tube. Check what your label on the sealer tube says and act accordingly. ;)
@robertyearian2273 жыл бұрын
How long did the changing of seals take
@DonnDIY3 жыл бұрын
One evening.
@stevewrightington15836 жыл бұрын
put the nut back on flywheel a few turns and put socket on nut hit with hammer two taps flywheel will pop right off
@leogagnon53395 жыл бұрын
Exactly what I was about to comment... simple fast and easy
@crankshaft10534 жыл бұрын
I just tap my hammer in the crank
@vwtaro2 жыл бұрын
What was the problem Don?The saw won’t start?
@johnclarke66475 жыл бұрын
Just run the flywheel nut down until it is flush with the top of the crankshaft and hit the end of the nut with a brass or hard plastic hammer while putting upward pressure on the flywheel. I use small pry bars to to that and the flywheel, after a few raps, will pop loose. They do make flywheel pullers but they are specific to each model of saw. I just do the rap method. With the nut screwed on to protect the threads on the. Rankshaft.
@JamesParus7 жыл бұрын
yep, getting two stroke to start and run with bad seals is very hard.
@DonnDIY7 жыл бұрын
It did start eventually with the choke fully on though. But yeah, the joys of two strokes... :D
@AndrewBrowner6 жыл бұрын
atleast it could be fixed for 10$.. a 4stroke will cost alot more when you get into oil seals and pumps and valves and rockers ect 2stroke small engines are the way to go if youre gonna fix them yourself.. if youre paying someone to fix them go 4stroke as 2 strokes typically have an issue yearly where 4 strokes can be quite reliable
@isotsakov91594 жыл бұрын
Very good
@DonnDIY4 жыл бұрын
💪
@Junk45087 жыл бұрын
what are you use oil?
@DonnDIY7 жыл бұрын
For the fuel mix my grandfather uses special Husqvarna oil, those little bottles pre-measured for 5 L of fuel. I used some generic oil while assembling the saw just to make the piston and cylinder more slippery.
@nadingjeff6 жыл бұрын
Awesome.
@nygardenguru5 жыл бұрын
Danka shein
@JuhaErkkila7 жыл бұрын
This was cool. Have to do the same for my 026 some day! :)
@DonnDIY7 жыл бұрын
That's funny, I have my 026 (MS260) waiting in the line for a top end rebuild and crank seals replacing. I will make a video of it for sure. Stay tuned. :D
@JuhaErkkila7 жыл бұрын
You can bet on it.
@jfox93177 жыл бұрын
What was the red sealant you used.
@DonnDIY7 жыл бұрын
Some generic engine putty.
@jorangel87 Жыл бұрын
@@DonnDIY how long you let sit before installing together?
@garengtutorial8923 Жыл бұрын
Keren bos
@fu420b93 жыл бұрын
Omfg to the drilling.
@fendtonafarm85137 жыл бұрын
Nice! How old is the chainsaw?
@DonnDIY7 жыл бұрын
Probably around 7 years I think. I remember the time when his previous Husqvarna blew the piston and he bought this one new.
@nutmeggrove84296 жыл бұрын
Nice.
@sthilthemiracleofalteratio95723 жыл бұрын
А как же опресовка?
@bonsaitree13507 жыл бұрын
Runs like a champ! Does gramps get it back lol
@DonnDIY7 жыл бұрын
My grandfather already got it back. He has a new saw already so it's unclear whether he will use it or not.
@agritechnicsvideography54977 жыл бұрын
You are a genious
@phillipkramer66387 жыл бұрын
You really had to get into that thing to replace those. Think they should be made of some special material instead of just any type of plastic or rubber like I have seen on different brands.
@jdailey198116 жыл бұрын
Phillip Kramer this is typical of the homeowner series of saws. The pro series has easy access to the top end bolts on top and can easily replace the top half an about 2 hours, if you know what you are doing. The homeowner series engines can be fixed, as proven here, but takes more time to get into everything. If you have the know how, you can take a homeowner model and replace things and they will last a lifetime, if you use them for what they are intended for.
@sergeyprohorov16594 жыл бұрын
Магнето снять минуту, на 1/3 откручеваешь гайку , берешь за магнето пальцами , приподнимаешь за магнето пилу и по гайке резко молотком бьешь.
@user-yd1oe5tj1u2 жыл бұрын
Так только наши умеют)
@roxy-tj3jo2 жыл бұрын
What does RTV mean
@andrewklein23492 жыл бұрын
Room Temperature Vulcanizing
@125dan67 жыл бұрын
cool !
@DonnDIY7 жыл бұрын
:D
@danhenderson7837 жыл бұрын
Should do a simple vacuum test on the engine before tearing into the saw.
@dstevenpaisley7 жыл бұрын
we use a match book cover to set clearence
@bborkzilla7 жыл бұрын
I've used a good stout business card for the same purpose!
@Wanous-hv7zo7 жыл бұрын
D Steven Paisley i use the Stihl tool
@olivierj.24353 жыл бұрын
Don't forget to use gaz resistant gasket maker
@carloscosta12805 жыл бұрын
Esse eu vi desmontando
@bradleyhofer44745 ай бұрын
👍🏽
@Chogall32953 жыл бұрын
Blue chinese seals... why?
@richardschofield22012 жыл бұрын
My original Stihl seals are blue from the factory
@Chogall32952 жыл бұрын
@@richardschofield2201 Original is between violet and blue.
@leoramirez40246 жыл бұрын
Go get parts from the web site called sawzilla they have much better prices and quality parts good luck on your next project
@magicone93272 ай бұрын
Please don’t go through this type of flywheel removal technique. Just put the nut back on the shaft so that it can be hit upon without hitting the threaded end of the shaft. Get a brass drift punch to hit the nut with. Place a wide blade screw driver or similar under the flywheel at a magnet location and against the main body at the top of flywheel. Apply slight leverage and wack the nut using the brass drift with a hammer. It will come off!
@jdubya545 жыл бұрын
Next
@Wanous-hv7zo7 жыл бұрын
take the china bearings out while you are at it
@usaisalwaysnumber15 жыл бұрын
no grease in the seal lips installing them? no dirko on the outside of the seals? I SMELL AIR LEAK...
@ivamsousa92756 жыл бұрын
..beya
@chiranagheorghitaeugeniuth983 жыл бұрын
you could take those seals apart just by prying them out. no need to tske engine apart. But good job overall
@usaisalwaysnumber15 жыл бұрын
word of wisdom REMOVE THE CHAIN AND BAR FIRST...save your hands..
@user-zs9ht6dp1j4 жыл бұрын
Я понял,что нехера непонял.
@fredo502505 жыл бұрын
wtf l'arrache volant
@alexandarpenchev71625 жыл бұрын
STILL 0 23 nombar1
@gouran217 жыл бұрын
Clear this filtr ;---------;
@DonnDIY7 жыл бұрын
Air filter isn't dirty, it only looks like it's covered with saw dust.
@johnkosheluk10416 жыл бұрын
By your self a knock off i am a cirtfide stihl tech
@punchogunter23624 жыл бұрын
You didn't show that you supposed to lube the cylinder wall and you didn't provide how long the gasket sealant supposed to set up before installation of everything else! Plus provide torque specs for screws!
@luksurias3 жыл бұрын
omg u go so wrong
@filipandonoski256 жыл бұрын
haha funny why u take off engine to change a bearing cap ?? that problem why chainsaw no start ?