My brother you are the best . I was just watching one of your videos and I see this one cool.😊
@Harshwardhanharsha2 ай бұрын
total FPV noob here - this video helped me get started with my rekon 3 ! and I would say its flawless!! Keep up the amazing work @drainman
@breakalegfpv9532 Жыл бұрын
so glad I use XM+, this is soo crazy.
@ibrahimalrabiah1179 Жыл бұрын
You always been very informative person, nice job, Here I want to add something maybe no one take attention to it (((SPI receivers DO NOT support D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) Modes (Packet Rates) and thus will not bind or sync with a TX module in any of these modes.))) so when you did above and the reciver not bound you need to change the frame rate from the radio to 500HZ
@DarthPenguinius Жыл бұрын
Thank you for this comment! I just got geprc tinygo with SPI and now trying to connect it to my tx12. Before I found this message about freq I thought that I can't connect it at all. But now I got at least some connection and trying to find details.
@pietrinico Жыл бұрын
Wooouh men, This kills the configuration of my other ELRS models a little, because I see 100Mhz full res fixed wings. 8Ch The drone arrives this week, I want to try it (and be able to bind it)
@bluegradientfpv Жыл бұрын
Perfect timing! My mob7 arrives Monday 🎉
@Tiemen_Deschacht8 ай бұрын
Thank you helped me a lot!
@techFPV5964 Жыл бұрын
Drainman it was your video of understanding Channel mapping that finally clicked in my brain and now my Baby Nazgul 73mm is arming and its flying very well. The one thing i noticed it does not have very long range maybe 70' and it drops out of the sky so i increased the power from 25mw to 50mw and hopefully ill get more range. Thank you for the simple videos which helped me a whole lot!!! You are tbe man!!! 😅
@gustofpv4470 Жыл бұрын
very comprehensive.....nice vid....I'm still stuck on frsky (it's actually worse than that - I still use ACCST), but I'm going to try ELRS soon .....your vid should make it easier!
@outdoorcreationsnwa Жыл бұрын
PLEASE DONT DO THIS IF YOURE A NOOB AT FPV. The video works, only if you know what youre doing. When you do this method you will get that error of “apply custom ports” or whatever when you re open beta flight. What this video fails to mention is, yes although you flashed to 4.4.2 you still need to attach the 4.4.2 DIFF file into the CLI in Betaflight otherwise your whoop will be all screwed up and not bind. The DIFF file basically tells your drone how to act and to be able to be bindable with your ELRS radio. I struggled for weeks trying to figure out what I did wrong from following this video, but it’s missing a whole other half set of instructions for you to do this successfully. Now that I know what I did wrong it’s easy, but if you’re new like I was at the time it’ll be a complete nightmare and you’ll spend 4 hours every night trying to figure out what you did wrong!
@Langor Жыл бұрын
i think i saw it on another video (by luck) that you backup your current version, and you can restore that section from the backup
@outdoorcreationsnwa Жыл бұрын
@@Langor yeah I had a group of guys on a discord who know their stuff who had me install the correct DIFF files back into the cli and it worked perfectly for me. But my rant was towards the newbies that have no idea what any of that means, just like me at the time it really sucked lol!
@Langor Жыл бұрын
@@outdoorcreationsnwa I know nothing. 😂 I just happened to get a different 1 minute video showing another way to do it. But for most people like you and I we'd be like "whaaaaaa?"
@andrebenjamin3289 Жыл бұрын
Somewhat unrelated, but i have an issue with one of my whoops and i was wondering what discord servers y'all are in that help with troubleshooting this side of fpv?
@freedeeztallbikes827 ай бұрын
Thanks for the info I’ll go ahead and dislike this video
@propwash80458 ай бұрын
How do from Yorkshire👍🏽 Thank you so much Drainman as I’ve just got my first spi elrs whoop and have been struggling just to bind the bugger . Bound it first time after watching your video. Bind phrase is awesome 👌🏽
@dayworkhard Жыл бұрын
binding phrases You LOVE IT. wE DO
@12felixjunior4 ай бұрын
Thanks for the video, just fund out that my transmitter had a older version of elrs , but I figured it out.
@jondoe6618 Жыл бұрын
This is a GREAT video!!
@ilhamismail29083 ай бұрын
thanks buddy im gonna try this out later
@outdoorcreationsnwa Жыл бұрын
The only issue I noticed for those new to this, when you do this it somehow screws up the video transmitter section in Betaflight meaning you won’t get camera feed to your goggles, and if you’re new like me, you’ve hit a wall and don’t know what to do next, you’ll ask around and those experienced will say it didn’t happen to them. Or maybe I just had bad luck! But I tried it on 2 drones with this method and both did the same. For those wondering, I did it on the Mobula6 and Meteor75 pro
@adamviaja9 ай бұрын
Got it all set up! thank you so much for making this!
@anthonydobija3669 Жыл бұрын
There is a led mouthpeice that has a circut board with 4 flashing differnt colored lights and can be placed on micros.very light.its only like a dollar.
@RoolandTheunissen Жыл бұрын
Good times have to re-watch 😊
@acriley87 Жыл бұрын
I’m giving up on getting my whoop in the air. Haven’t flown in over 5 years and I guess it’s gunna stay that way as I am at a loss. Unfortunately I’m going to be sending it back and selling all my gear. I guess flying again will remain a pipe dream.
@rapaduratv Жыл бұрын
oooh my godness i not believe! you the best Bro! 🎉🎉🎉
@f2f.photography10 ай бұрын
I was listening intently and then noticed your background wall. 🤣 I'm like... wait wut! I am waiting on the arrival of my first RPV .
@lynsmith1096 Жыл бұрын
Good tutorial. Just subscribed.
@SOKOL60A Жыл бұрын
Это Так Здорово!!)) Наконец я понял что означает набор цифр и как он связан с фразой. Я смотрю Еще Ваши ролики и по ремонту FC у нас говоря про таких - ПРСТО ВОЛШЕБНИК!++ Продложайте нас ОБУЧАТЬ!!+++ This is So Cool!!)) Finally I understood what the set of numbers means and how it is related to the phrase. I also watch your videos on repairing FCs, talking about such people - JUST A WIZARD!++ Continue TRAINING us!!+++👌👍😜
@justt4der8717 ай бұрын
Really good vid really informative nice work
@julienrodrigue917011 ай бұрын
You are the best!!!!!!
@DannyFPV04 Жыл бұрын
Can you flash new ELRS versions to aio flight controllers to keep you transmitter updated to newest firmware?
@tanoenaczycaitin Жыл бұрын
thanks Bro.. you got me sort my quad out..
@LordRejion8 ай бұрын
I tried to follow along. I just got the elrs boxer radio. And I am clueless to this stuff. I backed my stuff up. But I don't know where it is in my computer. And I messed my set up up or. Messed it up and never finished.. I don't know what to do. And don't know who to talk to about it. When I press my sys button. I have no tools. The radio now when plugged in... I hit USB. The one page comes up that I'm not supposed to touch. But not the other USB page . I've watched a lot. Tried 3 different videos.. and I messed it all up. And I don't know how it's supposed to be. Should I erase everything.. only thing I know to do.. but I don't know what is supposed to be there from the factory. Hope I'm making since..
@no2lagwev251 Жыл бұрын
Super well made. Very useful!!
@tanahhuat1757 Жыл бұрын
Thanks for the tips Sir. Awesome
@BeachbumfromBrick2 ай бұрын
So are you saying I should buy that RAD controller you have and make life easier ??
@MichaelRogersJesusrules4 ай бұрын
Hey DrainMan .my mobula6 analog wont even connect to betaflight but its bound to the new pocket ..ill be binding the eco 2024 hdz to the tx16s if i ever get this connected :0 thanx for all you videos there always in depth:)
@Les_Grossman Жыл бұрын
Are you missing the most important point in Method 1 and 2?? Same FW Version on TX and RX??
@dennismatovich84119 ай бұрын
well done!
@chestergt7765 Жыл бұрын
Damn. I should have paid attention to the presets for the VTX and the other stuff.
@jayzzz1234 Жыл бұрын
Sup drainmam
@thatguythere98 Жыл бұрын
Really great stuff man! I got a baby Nazgul a few months back but I broke it and had to get a new board, I chose one with ELRS on board. I could not get the thing to bind no matter what I tried so I decided to start fresh and follow your guides step by step and it works like a charm. Subbed!
@-KillerHawk-9 ай бұрын
5:59 looking cute
@getitdone361 Жыл бұрын
Can i use the easy method to bind more then one to the radio i plan to have 3 or 4 drones just want to be able to grab or or the other and it be good at all times
@techFPV59647 ай бұрын
Hey Drainman I have an Iflight Alpha 65mm V2 whoop drone however it will not bind with my Taranis QX7 that has not been upgraded yet, is there a way around avoiding to upgrade fw on my radio? Thnx! ✈️👍
@HorstLagerfeld Жыл бұрын
If understood right, you can bind any spi receiver even the dsmx from spectrum with an expresslrs transmitter? How does this work?
@nfconstruction108711 ай бұрын
So I just got a mobula 8 did the back up flashed newest b.f. put tried all 3 methods can’t get it bind I have ran through all the ep1 on kustom 5” worked fine also mobula 8 won’t go into Wi-Fi mode I’ve seen other do the WiFi binding fraise have reflashed radio a few time double checking binding fraise am I missing some thing or got a bunk kwad
@Marcus-xl9krАй бұрын
What if my board has built in elrs reciever but uses crsf?
@tristantamdalque7334 Жыл бұрын
Is it good at mobula 7 1s
@Todd_G_FPV5 ай бұрын
Will a crossfire rx bind to elrs tx? Goggles says yes but I don't see anyone explaining how
@benherr27369 ай бұрын
Dumb Question.... I only have one quad with ELRS using a Taranis QX7 with module If I set it up The Easy Way and find I want more ELSs receiver's can I rebind the first quad later? Thank you in advance, Ben Herr
@freedivecraig2 ай бұрын
hi Drainman I have been trying to follow your directions for connection on my emax freestyle 3 to bind with a radiomaster pocket. and it keeps telling me failed to open serial port every time I try flashing. can you help please
@montrodg2 ай бұрын
Hi, how are you? I have an SPI board and I have followed all your steps and I cannot connect the drone to the controller. When I type get expresslrs it tells me an error and does not give me the code. Can you help me? Tell me about step 3.
@kylenordhaus8808l Жыл бұрын
There any way to just get by all the pc stuff? Currently living on the go so having a computer is difficult for me
@kardady Жыл бұрын
Thanks man 👍👍😍
@getitdone361 Жыл бұрын
Does the radio firmware mater ir as long as uts same phase dont mater ik it used to have to match been along time since ive done anything with drones
@jrhager848 ай бұрын
Bind receiver button is missing. How the heck do I do it?
@MrDee-x7j8 ай бұрын
I am on betaflight "Firmware: 4.3.2 BTFL" . I do not see bind option while navigating to "Receiver" section. Therefore, I tried "bind_rx" on CLI which throws error as "ERROR IN bind_rx: Not Support". Any idea what I might be missing ?
@bunnykiller Жыл бұрын
I was given a RadioMaster TX16S loaded with EDGETX_tx16s 2.8.4 selfbuild 023-05-20 along with an Mobula6 900/915 ( dont know if its 900 or 915 ) Blueframe whoop with a CrazyF4 ELRS V1.0 AIO board loaded with Betaflight 4.4.2 STM32F411 CRAZYBEEF4DX f3f3a3c2.hex... this thing will not play nicely, it wont bind. What FW./SW do I need to use to get this combo to play nice, and who do I DL it from?? Express?, Radiomaster?, EdgeTX?, OpenTX?, Happy Model??? I now understand why this combo was given to me, the previous owner could NOT get it to work either... and BTW Betaflight "sees" the reciever and it moves the model on the screen when moved in real time... any help or direction to a solution would be greatly appreciated... forgot to mention, it also has a Happy Model 900 TX add on pack in back....
@vuchuong74 Жыл бұрын
If your radio is talking to your drone when connected to betaflight the check the values min and max throttle when you fully deflect throttle stick. If not set right it won't arm? Just a guess.
@vuchuong74 Жыл бұрын
Oh wait you are talking about binding. 1. Just upgrade or flash radio firmware to latest EdgeTx (may not be essential). 2. Flash the Elrs module (internal or external) to the latest version (elrs v3.xx?). 3. Flash betaflight to drone if SPI as in this video. Note elrs Tx v2.xx firmare will only talk to Rx v2.xx. If your radio elrs module had v2.xx then betaflight v4.3 and above have elrs v3.xx baked in? Maybe that's why it won't work. I am still on elrs v2.xx but will update my gear in a couple of months. Hope I dont fuxup 😂.
@Hrichs Жыл бұрын
Followed this guide with jumper t pro v2 and I still can’t bind! Please help.
@Jmagdiel6910 ай бұрын
Help help me please, I’m putting bl in beta fly but isn’t working, is not showing the DFU name
@ChristKrew-Rev1.8 Жыл бұрын
Hey DrainMan... will this work if I have spi elrs RX's with v2.0 on them? A little gun shy as I am unsure about updating my TX module and loosing use of all my quads. Firmware gets me every time lol. I am looking to put a rig together to get friends into fpv.
@Krash_fpv Жыл бұрын
Mobula 7 1s with frsky spi.....took 4 days to fet setup and bound properly.(nothing was working) and then it falls out the sky every 20 sec and says rx loss....video is perfect but not rx signal....ordered a zorro and express lrs and hopefully i can get a serial rx to work on it
@parkour_dad Жыл бұрын
Can't connect the boot loader. When I type in the command bl from the cli it fails to open the serial port and I don't connect to the bootloader
Binding FrSky quads to FrSky radios or modules should be very easy. Should not need to mess with firmwares at all.
@gabormihaly667 Жыл бұрын
Why did you pile up so many drones around you?
@Blizofoz45 Жыл бұрын
Tried the first two methods and they didn't work. The third way is absolutely ridiculous. Looks like I have a $270 paper weight.
@vuchuong74 Жыл бұрын
Its a bit of a learning curve but stick with it. Will be worth it in the end. There are many points not covered in this video. I suggest looking up Joshua Bardwell's tutorial for things concerning elrs. Or Painless 360 is pretty good too.
@Blizofoz45 Жыл бұрын
@@vuchuong74 Figured out I had to turn down the packet rate. SPI receivers won't bind if the radio is set at packet rate for serial receivers.
@tommaillard14152 ай бұрын
"the two shall connect, oh don't do that..." 💀
@bull_shannon_fpv Жыл бұрын
Not into fencing? Not that there's anything wrong with that🤺
@shanehinckley51803 ай бұрын
Fencing vs hema
@bunnykiller Жыл бұрын
now I know why they call these tiny quads "Whoop", when it comes time to flash and bind, they will WHOOP your azz...
@mitchfowler646 Жыл бұрын
Still don't work elrs sucks. Update oops don't work,binding phrase now spi don't work no matter what everytime I have to bind a new whoop it is hell. EVERYTIME
@slappomatthew Жыл бұрын
only 10% of viewers are hitting the like button. give this man some love. he needs to blow up like and comment so he can get some sweet sweet google $$$
@breakalegfpv9532 Жыл бұрын
none of this is working anyone need a zorro radio and 2 quads there in the dumpster now.
@darielsabay1391 Жыл бұрын
you cant bind elrs?
@vuchuong74 Жыл бұрын
Sorry to hear that mate. Elrs is very elegant, has very good range and stability for the price, but does require a small learning curve. I am sure there are people near you that may be able to help if you stuck with it.
@drdamonjackson4529 Жыл бұрын
Great timing, I'm just getting into ELRS from the sbus. I'm excited to learn something new. Thanks for putting this together.