Drill Pipe Running_ For DERRICKMAN drilling machine drilling oil and gas oil and gas industry

#interesting #petroleum Engineering #problem and solutions
#drilling oil and gas wells #land rig drilling operations #tds drilling rig #drilling rig components and function #drilling rig components #national oil company #oil well drilling #oil well drilling process #drilling oil and gas #drilling machine repair #drilling machine #drilling problems and solutions
#drilling process steps
#drilling process in oil and gas #drilling process #oil & gas development company #drilling professionals #drilling problems and solutions
#drillpipe #running #trip #coil #drillingmud #oilandgas #oilfield #rig #drillingrig #drilling #nice #oilwell #derrickman #floorman #Asst-Driller #drillers #varco #vfd #vfdd #scr #plc #landrig #ironman #beautiful #drillercabin #scrrig #vfdrig #beautiful #mud #hivis #video #viralvideo #national #nice #oilwell #derrickman #floorman #Asst-Driller #drillers #varco #vfd #vfdd #scr #plc #landrig #ironman #beautiful #drillercabin #scrrig #vfdrig #beautiful #mud #hivis #video #viralvideo #national

[@nananang5127]

Top driver DERRICKMAN easy money

[@ricktbdgc]

Easy job

[@DELTA_N9NE]

That's CADILLAC work. When I broke out in the Derrick you had to throw that pipe out there and latch them elevator's by hand on the run. I did break out on an old 50's model rig though.

[@rajakhurram1196]

MASHA'ALLAH MASHA'ALLAH, ALLAH NAZER SE BACHAYE BHAI KO , LEKIN ROPE ZAROR DALIEN PYARAY BHAI

[@nabadipgogoi1877]

Nice short❤

[@brucemorris6319]

Man that just blows my mind seeing that. I worked derricks back in the 60s and 70s. If you told me back then that the Derrick hand could latch pipe and never touch the elevators in the future I would have laughed in your face .

[@DELTA_N9NE]

LOL I know man. I broke out on an old 50's model rig and is was work no matter what you did plus we dug EARTH pits by hand. No metal containers for drilling fluid back when I broke out. Now days you probably have to fill out a job safety analysis sheet before picking up a hammer lol.

[@mikedawson1907]

@@DELTA_N9NE the rigs I currently work on we throw it but still have to manually latch

[@lightningdad13]

kzbin.info/www/bejne/bYjUpZ-IapaZf7c watch this video and you will see me latch pipe from back of the board.

[@Raptor4fx]

Wait til you see automation

[@WaqasAli-ky3ly]

👍

[@f.s.6536]

good

[@leooneill1693]

No hard hat, well done genius!

[@mushtaqhussain4774]

Good

[@johnnyellis4987]

Try it on a old school rig with swing blocks not much fun

[@AnilKumar-om2qe]

Nice brother

[@mosinholic2695]

Nov rig... same my rig.... easy to work.... which rig is there and location?

[@dalvirsingh8797]

Gud job

[@namasteworldone]

Hiiii

[@ConnorLyon]

That's it??

[@wrongway100]

Hey did you guys check the water in the crown

[@bobfeller604]

If I was young again I'd be there.

[@aleksivanov6976]

Обычно свечу кинул в элеватор, и когда её с подсвечника срывают сверху верховой должен веревкой её поддерживать. Иначе внизу трудно будет ниппель( наружная замковая резьба в нижней части трубы) в замок вставлять ....Мы так делали.

[@joelezekielbruce1060]

This skill looks great easy my little brother baby could manage.

[@мажитмажит-с2д]

Сам буровик 👍👍👍👍💪💪💪

[@saidbah3171]

RIH with DP 5", I like working with Topdrive as a DD.....

[@BubaRedneck]

Worked derricks in the 60's n70's ran 18000' of 4 1/2 pipe and 6 stands of 6 in collars when the bits were harden steel and not diamond coated carbide. that means 4 to 5 hours on bottom and trip it again.

[@SideStrafed]

4 1/2 dp and 6 in collars are baby pipe. Easy to rack back

[@BubaRedneck]

@@SideStrafed So what size pipe did you run, and what wait per ft?

[@SideStrafed]

@@BubaRedneck we’re running ptech 5 1/2” Dp and 5 1/2” HWDP.

[@cravenm.2295]

U guys r both women. I ran 7 inch drill pipes and 10 inch collers and we trip every 2 inches we drilt that was in the dessert back in the 70s it was 140 degrees farinheight at nite

[@rudrajitgogoi2714]

Shaktiman. Shaktiman 😄😄

[@davidd.foxell4271]

And you're proud of yourself 🤣😂

[@DELTA_N9NE]

Lol self latching elevator's. That isn't roughnecking unless you're leaning out there and grabbing them horns to latch that sh1t by hand.

[@lightningdad13]

@@DELTA_N9NE I can latch pipe all day long without touching the elevators.

[@lightningdad13]

@@DELTA_N9NE and no they're not self latching elevators either. kzbin.info/www/bejne/bYjUpZ-IapaZf7c

[@sangwarok1862]

Our content is not much different

[@mikedawson1907]

Wtf I have to shave my beard at my company !

[@ikramkhattak6680]

Unsafe because incase mess you stand big hazard,first stop travling block and then throw the stand

[@GordonTurnerr]

HAHA as if

[@1Imrichard]

@@GordonTurnerr thats easy as fuck .

[@1Imrichard]

he is almost stopped . people would die of boredom

[@bwoodard907]

We only stop for BHA but…. With that said we expect one hand on the horns before you throw one in the elevators. Moving blocks and tripping is very safe if a PJSM is held and the driller, derrickman and floorhands are all on the same wave! Stopping is all good too if you feel it’s necessary but over time you will get behind the well plan and I have no doubt the company man would shit twinkies if he was watching you trip like that. Hahaha

[@Rigworld1]

👍