DRIVESHAFT DELETE!

[@Shawn_42850]

Poor Berger 😢 that thing mangled everything under the car!

[@ogsuperflygarage]

My hats off to Berger for being a go getter and not giving up!! That’s a scary thing for the driveshaft to let loose like that… I am so happy that they are ok Brother!! Driveshaft safety loop time!💯👊🏾

[@paulhudgins5120]

Man that sucks for Berger, it's a never ending bad luck, good thing is nobody got hurt, big time damage underneath.

[@scottglaister158]

glad nothing bad happened to you guys !

[@scottharvey3054]

Holy chit….. I had a front u-joint failure on a FMS D/S, thankfully I had a Metco loop that saved me…. And it still sounded like a gunshot inside the vehicle… I’m so glad those guys were not hurt !!!

[@blainmcdevitt2495]

Man, that’s sucks. Poor guy. It’s never ending with these cars.

[@ilike9s]

Hang in there Berger.

[@mrbighands]

that's why I have a driveshaft loop installed, on my 91 LX Coupe 5.0 a must-have.

[@nunya2814]

Man hes lucky that thing didnt come thru the bottom of the car and say hello. Looks like it got the fuel lines too, glad no one got hurt though.

[@bobbysmith4783]

Dam. Id recommend the ptfe lines from evil energy. Cheap and ive been running it on my fox for 2 years without any problems. Glad everyone's unharmed.

[@cleonclink6811]

Damnit that sucks. Berger works damn hard to make that car nice and then this shit happens. It’s just car related problems though, it can be rebuilt. Future content!

[@glennramsey917]

Theres simply no place to quit … be like one of those guys that just don’t have no quit in them … ppl can look at your car and appreciate the work thats been put into it but only we appreciate the grind that it took to get it there !!!

[@rr122608]

It could have been worse. 😬 Verger’s fox will live to tell a story. ❤

[@pimpovic2]

When it rains it pours. Thankfully, tomorrow is another day and you have many hands to help out.

[@rolandlluis3153]

" The Twizler " 😝

[@ryandoyle4344]

Positive vibes sent, Best wishes Berger! If both tkx had an input shaft (4th gear) issue, check the run out of the bellhousing (aka: index or center aligment). Some need offset dowel pins to properly index their TKX bellhousing. If not in proper alignment, the input shaft bearing will wear out. GL

[@bama_5.051]

Damn it man I hate to see that brother ..atleast no one was hurt.. Well it was right in front of the barbecue shack you could have gotten a sandwich..

[@imichaelburger]

😂😂😂

[@jimmyjamesgarage3290]

Damn that sucks man! I feel for Burger. That was painful to see at the end.

[@jcnpresser]

Dang that sucks man. Think that happened to my car before I got it, it’s got some questionable dents in the floor board trans tunnel area. I’ve got a old steel drive shaft if y’all are in ky any time soon or come up for ford fest, it needs a new companion flange for the rear diff end, the u joint fits little in the loose side and has a touch of play, but if his is ok then you could swap it. Other than that it seems to be good. Has new u joints in it.

[@jesseworkman4418]

Dammit Man 😂

[@noahsfifty]

Had my Ujoint break off, Cracked my input shaft retainer, entire bellhousing, put some gnarly dents underneath and in my bassani x pipe

[@dylanmorgan1440]

Wow that's heartbreaking.

[@H.O-T.V]

Seeing the issues with tkxs lately, im glad I found a good deal on built gforce t5 with gforce case.

[@BigKidsRC]

Wow crazy man sorry Mike but cant wait to see a rebuild ive sold a cple of my foxes over time for things like this lol

[@theANGRIERone]

Hey, if you're gonna break stuff, don't half ass it. Lol

[@robaxelsson530]

Wow!! Looking forward to you guys diagnosing the cause..(u-joint, slip yoke)..would a drive shaft loop minimized damage?

[@wadestewart901]

Man, I had an aluminum quadrant that was the culprit on mine. I changed cable after cable. I even went hydraulic! It wasn't until I was installing the Hydraulic set up that I noticed the quadrant was digging in the mount! I was pissed, but that's the foxbody way....

[@gennarohock1572]

What do you mean by digging in the mount what mount

[@RandallMullis-d8e]

I have a stock manual drive shaft if you need it. No charge in GA.

[@Spartacusfinkle]

Time for a Wifi driveshaft!😅

[@BREW2LFOXBODY]

🤣

[@matthopkins1107]

Been fighting a rich idle for months just throwing parts at it. New ecu, MAF sensors. Welp today I pulled a vacuum line off that was ehh looking and gas poured out. Diagram in the fuel regulator went bad. I think

[@91foxbody]

Had my fox drive shaft let go, scary shit! Thought I was done!

[@VictorSanchez-kp9nt]

Dang it that's not good but like we all know it never ends. I'm dealing with a brand new power steering pump squealing yet again I mean how many times do I have to do this before it's right? Manual rack? Yadala. And that's just one of a handful of issues I've dealt with. Foxbody life.....

[@sn95garage18]

Are you guys checking the run out on your tkx installs . ?

[@BREW2LFOXBODY]

Yes sir

[@sn95garage18]

@@BREW2LFOXBODY ok great . I hope Berger is going to get hooked up with stifflers drive shaft loop . I felt so bad for the kid he’s been busting his ass non stop on that car it’s came so far . I guess I gotta good tkx mines been problem free for 2.5 almost 3 years

[@TommyT236]

Clutch cable hot without the car running??? Clutch cables are not ground wire. I’ve seen it before.

[@BREW2LFOXBODY]

It was from the friction within the cable

[@richlong4119]

The dirty South 🤘

[@russellbroadwell]

At least it didn't come up through the floor.

[@gennarohock1572]

I bet they didn’t tighten the driveshaft bolts correctly when they were in the floor

[@ThaSilentOne420]

💚💚💚💚💚💚💚💚💚💚