How to Design ANFIS Based Boost Converter Model in MATLAB Simulink Software | Dr. J. A. Laghari

[@muhannaddrakalsebai4839]

Jazaka Allah. It was a simple explanation how to apply ANFIS in MATLAB Simulink.

[@DrJALAGHARI]

Thanks for the compliments.

[@hamidov123]

Thanks you si mush its thé first Time i understund thé anfis بارك الله فيك

[@DrJALAGHARI]

Thanks for the compliments.

[@oladipostephen8501]

Thank you Dr. Laghari for all you are doing.

[@DrJALAGHARI]

Thanks for the compliments. Do share it within your circle too so that they may also get benefit from it.

[@jimohabdulramonaroyehun919]

Thank you sir for your immense contributions to knowledge. Allow me to also use this medium to express my profound gratitude for wonderful KZbin video you have done in the past. I enjoyed all. Once again, thank you sir

[@DrJALAGHARI]

Thank you so much for the compliments. kindly share it within your circle too so that they may also get benefit from this video as well as channel.

[@jimohabdulramonaroyehun919]

Alright sir. Regards

[@jimohabdulramonaroyehun919]

@@DrJALAGHARI Alright sir. Regards

[@Syed-wb8lc]

Thank you DR JA Laghari

[@DrJALAGHARI]

Most welcome

[@Eng.ashrafLateef]

. Thank you for the interesting video .. I have a master's thesis on the use of ANFIS for a solar system and I am trying to control the output voltages .. and I assume that the load has changed after a short period of time from operation .. but there is a failure to maintain the output DC voltage level .. Note that the PI succeeded in maintaining the voltage opposite the ANFIS

[@DrJALAGHARI]

Thanks for the comment. ANFIS needs proper training for all events. Therefore, try to train it properly to get the desired results.

[@vibinrajan7636]

Really, an informative & very useful content. Sir, kindly upload research topics on AI based "Energy Management System" on power systems..

[@DrJALAGHARI]

Thanks for the compliments and suggestion. Ok I will try in the future.

[@Kashifbhangwar103]

muhnje University life jo behtreeen teacher Dr javed ahmed❤️❤️

[@DrJALAGHARI]

Thanks for the compliments

[@sebasthiranikathalingam9416]

Thank you very much sir

[@DrJALAGHARI]

Thanks for the compliments.

[@barisukauebari8563]

Thank you Sir for the great work you are doing. Please can you also make video using GA and PSO to design boost converter. Thank you.

[@DrJALAGHARI]

Thanks for the compliments and request. Sure. I will try to make video on this topic as soon as possible.

[@Syed-wb8lc]

If i want to apply two or more than two ANFIS controllers then how can I apply them Sir??

[@DrJALAGHARI]

Thanks for the comment. Just use two blocks and train them separately and use them in the model.

[@attiqullah5195]

where is ANFIS data to use for training...?? Plz provide it.. As you have uploaded for AVR ..

[@DrJALAGHARI]

Thanks for the comment. The file link is given in the description section of the video.

[@nomanmreedha5235]

How to train the model for boost converter with variable input?

[@DrJALAGHARI]

Thanks for the comment. For variable input use the varying signal by using signal builder block or something like that to include all values then train the model with the anfis.

[@nomanmreedha5235]

@@DrJALAGHARI I've used the signal builder block. I meant in the workspace how to change the output data? ( this is not the conventional boost converter,I'm trying to optimize a converter I found in a paper) I tested the duty cycle needed for specific input voltages. For example my dc input varies from 80v to 40v. For input 80-74v range there were overshoot and undershoot. So I checked the duty cycle needed for 80v,78v...74v. There were 2000000 samples in total, so I divided all the samples by 40. That gives 50000 samples per unit voltage. And then I changed the output for each 50000 samples with the duty cycle I obtained before. But that's not working,the output is worse than what I got from the PID controller. Am I doing it wrong?

[@DrJALAGHARI]

@@nomanmreedha5235 thanks for the comment. In that case, kindly follow the paper methodology.

[@nomanmreedha5235]

@@DrJALAGHARI The paper used normal PID controller. I'm trying to get better result than that.

[@saleemriaz5760]

AOA respected Sir can you please share the code or video for Grey wolf optimization method ? GWO algorithm

[@DrJALAGHARI]

Wa'alaikum salam thanks for the comment. At the moment, I don't have this code. But you may search it in Google.

[@nimrahsaeed002]

Much appreciated. Sir, are you in Pakistan right now?

[@DrJALAGHARI]

Thanks for the compliments. Ye. I am in Pakistan.

[@nimrahsaeed002]

@@DrJALAGHARI sir can i have your email address plz

[@MuhammadHamza-vy2ls]

Can we use this with Mppt solar ?

[@DrJALAGHARI]

Thanks for the comment. Yes sure you can use it with MPPT solar.

[@EISHANSHARMA]

what if there are multiple inputs in a controller

[@DrJALAGHARI]

Thanks for the comment. You can use more than one inputs if they are required. In that case use the multiplexer block and combine them in one signal and then give to ANFIS.

[@RevathyKP-rv8gs]

SIR CAN YOU POST VIDEO ON PSO OPTIMISATION IN DAB CONVERTER

[@DrJALAGHARI]

THanks for the comment. No. I dont have.

[@dnhj24]

Sir,can we design anfis for buck converter

[@DrJALAGHARI]

Thanks for the comment. Yes. Ofcourse. You can apply ANFIS for a buck converter too by following the same strategy.

[@mahfoudiarabah8684]

thanks

[@DrJALAGHARI]

Most Welcome

[@nachobunbury9111]

make discrete wavelet transform video in hdl

[@DrJALAGHARI]

Thanks for the comment. What do you mean by hdl?

[@electrictrick1360]

Hi

[@ataurrahmaneee6492]

plz check our mail. have some problem task sent to you.