DUAL 1009 (1000 SERIES) TURNTABLE MOTOR REPAIR

  Рет қаралды 5,426

audio

audio

2 жыл бұрын

REMOVAL, DISASSEMBLY, CLEAN, LUBRICATE & ASSEMBLY of DUAL 1000 SERIES TURNTABLE MOTOR

Пікірлер: 9
@BlakelyPhillips
@BlakelyPhillips 6 ай бұрын
Thanks so much for this! I have a 1019 with a motor whir I've been afraid to try and fix. Feeling better about giving it a shot now.
@elliottcrews4997
@elliottcrews4997 2 жыл бұрын
I did this with a 1229 a while back and it does indeed test one's patience. But it is a great feeling of satisfaction when it's done isn't it!
@dchampion267
@dchampion267 2 жыл бұрын
THANKS! Exactly what I needed. I'm going to give it a try.
@davesanders4381
@davesanders4381 10 ай бұрын
What about lubrication for the upper motor bearing; you only did the lower?
@bones007able
@bones007able 10 ай бұрын
My 1009 I can't get the tone arm set right ... push the start lever and it will cycle and just shut off... if I hold the start lever until the arm moves then it will work , the little hook that keeps the TT on slips off the loop when I push to start ... if I adjust it just a hair ... the hook wont get pushed off by the arm at the end of the cycle , so it will just run continually ...
@__gene
@__gene Жыл бұрын
Thanks a lot the video was very helpful and worked well for me. It was not necessary for me to disconnect the wires of the motor. Unfortunately the speed adjustment of the idle wheel is now misaligned. Have to put the switch to 16 to play a 33 and it's a tad to slow. Any advice how to fix that. Cheers
@jedbrady4711
@jedbrady4711 7 ай бұрын
I watched your video and have a question for you if you dont mind. I have the 1009 sk2 and when the idler arm contacts the motor it makes quite a bit of noise. spin the idler arm or motor by themselves and you dont hear anything. I think it is the contact between the two making all the racket but not sure what I can do about it. Almost feel like the idler arm should have some type of rubber band that goes around it. Any ideas? Thanks
@audio4335
@audio4335 7 ай бұрын
Perhaps the Idler might have hardened with age. Good luck
@jedbrady4711
@jedbrady4711 7 ай бұрын
@@audio4335 that seems to be the consensus from others as well. I appreciate you taking the time to respond back to me. I am looking to buy one now. thanks
Frustrating Dual 1019 Turntable Repair - Turntable Won't Shut Off
22:56
MillerVintageHifi
Рет қаралды 3,4 М.
Garrard Motor Repair Synchro Lab Turntable
5:40
xfireamg
Рет қаралды 1,6 М.
Despicable Me Fart Blaster
00:51
_vector_
Рет қаралды 25 МЛН
THEY made a RAINBOW M&M 🤩😳 LeoNata family #shorts
00:49
LeoNata Family
Рет қаралды 43 МЛН
Beautiful gymnastics 😍☺️
00:15
Lexa_Merin
Рет қаралды 15 МЛН
What it's Like Owning a Vintage Stereo Store in 2024!
17:38
Skylabs Audio
Рет қаралды 25 М.
Dual turntable repair constant on and off problem - SOLVED
5:00
Dual turntable steuerpimpel replacement (701, 1209, 1219, 1229 etc.)
10:19
ArtOfVinyl Turntable Repairs
Рет қаралды 49 М.
Pro-Ject Debut & Xpression Motor hum and Noise Fix
19:55
Northa40
Рет қаралды 27 М.
The BOSE Prototype that Never Made It
20:54
Mend It Mark
Рет қаралды 117 М.
Dual 1019 in the worst condition I have ever seen
1:11:04
12voltvids
Рет қаралды 24 М.
Dual 1225 Servicing
22:31
Amorphous Audio
Рет қаралды 47 М.
Despicable Me Fart Blaster
00:51
_vector_
Рет қаралды 25 МЛН