Dual Humbucker w 1 vol and 1 tone

[@miltonrobinsonquininires9493]

Thank you, I did it on a guitar that I built and it turned out spectacular, a hug from Argentina

[@TomClarkSouthLondon]

You are the Greatest and VERY much appreciated 👍🙏🏽

[@jerveman]

This was by far the most informative video I have watched so far regarding the DPDT pot wiring. Most videos only show the casing with the 6 terminals for soldering, but don't show the rest. ...I went to many videos and they didn't even show the Complete wiring diagram, as you so WONDERFULLY displayed. When someone searches youtube to install a new guitar part, YOU ARE THEIR SAVIOR. Bless your heart and I will subscribe/like this video, whole-heartedly. my guitar WORKS NOW. I just need to figure how to include the 2 wires I taped together on the 2nd humbucker on the DPST switch so I can run from 1 coil from each humbucker.

[@jerveman]

btw, I am running 2 humbuckers (with 4-conductor wires, each), a dpst pot as volume for the bridge, a 500k pot as volume for the neck, and a master tone switch. [NOTE: every part in the guitar is grounded to the switch through a chain of soldering points and wires]. It works but no parallel or coil split action :\ ...There is a learning curve with guitar repair, like anything else in life.

[@joes.1836]

You just saved my sanity!! Great video and clear explanations video! Now I just wait till my solder wire and new tips arrive so I can do a proper wire with my new lace sensors! If you still check your videos for comments, you rock!

[@Reid6505]

I'm replacing an active system with passives and have 2 knobs. This helped a ton, thank you!

[@donrepcon7704]

Amazing. This is exactly the video I needed at the exact time I needed it. Great timing. Thanks

[@nicktodorov669]

im so fucking glad you made this video. i noticed my guitar wasnt producing sound unless on overdrive channel on amp and it was coming out clean. its jackson dinky js 11 with this exact schematic and noticed the middle position of the pickup switch wire had broken. using the schematic i figured out where it should connect and did a quick test while touching it to the solder point while strings were ringing and it made a sound. youre the best

[@nrthrn_dcy]

What a coincidence lol, I have the same model of guitar that was used in the intro. Sweet, I'll have to work on that soon.

[@c420_nights]

Your voice is a perfect blend of Iggy Pop and Mike Judge.

[@tunemeister99]

Very concise and detailed tutorial. Excellent video!!!

[@chrisball8080]

Fantastic. Very well presented. Just what I needed to know. Much appreciated. Cheers from OZ, Chris.

[@garyheighway7635]

Wish everyone would explain it this easily

[@kornvirat]

Great video Thank you very much

[@kromus1]

I was looking to do exactly this, so thanks very much for the help 👍

[@barrykimber]

Exactly what I needed thanks

[@alfons1976]

Great video, super well explained. Just what I needed. Thanks for posting!

[@robertirby4605]

fantastic video, super helpful

[@ronin2167]

There is an updated corrected version of this video. The cap should be grounded to the tone pot and then connected to the middle connector L2, not L1.

[@jnicholls21]

You saved me some hassle here, my man. Cheers.

[@davidkennedy1271]

I agree with doug.....it would have been nice to see this without the push pull. Then it would be probably the best video out there for the newby's

[@johnheick3205]

@Possumlove hahaha yeah that's what it seems like. It doesn't exist because it's just "assumed". So it's pretty frustrating.

[@sbrave]

​@@johnheick3205 Check this out. guitarelectronics.com/2-humbuckers-3-way-toggle-switch-1-volume-1-tone/ I guess you wire a long connection from the switch to the pickups, unless you have a PRS or SG type guitar. I was curious about this too.

[@christiandad9369]

Why are so many people thanking the person who uploaded this? It’s just a breja toneworks reupload. (If you are reading this breja is great and def worth a look)

[@_viy]

Can you do the same diagram but with two volumes for each pickup and the coil split for each pickup also. So set up will be two 500K push-pull pots for each humbucker & 3 way switch.

[@cesargonzalez8260]

On the bridge pickup, how do you connect the black wire to the 3 way switch and to the tone knob if you only have one black wire on the pickup?

[@dandresaldi]

Great video, I´m going for my second guitar mod (the first was just changing pickups connecting everything like it was in an Ibañez RG prestige because the switch it has is really complex for me (VLX91). In my second mod I´m changing pickups of another Ibanez and also installing push pull pots for coil splitting and different pickup combinations, the with it has is simpler, its a 5way Ibanez COR-TEX. Do you have a video of a more complex project involving a 5 way switch or super switch ?

[@edwardcastro6864]

thanks for the video!!! looking forward to emailing you. With my wiring problem and questions.

[@scottwillis3281]

This helped me tremendously! Thank you!

[@FairlyUnknown]

Stolen video re-uploaded. I don't understand how this has stayed up for so long, but I am reporting it to the original owner Breja ToneWorks to hopefully file a copyright claim. Better late than never.

[@cugir321]

report it to youtube

[@FairlyUnknown]

​@@cugir321 I would absolutely love to, but KZbin's system only allows the actual owner of the video to issue a report, which is silly because if that person is no longer around on KZbin there is basically free reign to re-upload old content without any repercussions.

[@HigherPlanes]

You know what else gets stolen, your tax dollars. Go report it.

[@joshualoveless20]

@@HigherPlanes Ha ha ha ha ha! Good one!

[@patrickmoreno5950]

If it's an instructional video, who loses really? It's not an original song.... It's help for a community. Such a silly thing to be offended by. The video even has the original breja notice... I don't think this person is stealing any value or intellectual property ... They're reposting an amazing video that they (and I) have found incredibly helpful.

[@williamshilling2198]

Suppose I don't want to put a push pull switch then where do I make my connection the on the pot?

[@profemartinez2672]

Confussion: Why the South Hummbucker split coil switch connects black, green and red? the black (hot) is not supposed to go to the selector, and the green/red are not supposed to go to ground when the switch gets pulled? I mean, in the same way that the North Pick up... on the other hand: white and red are not supposed to interconnect instead the green???

[@elliottsmith8636]

Damn, was gonna use single coils but they aren't very splittable. Who'd have thunk it?

[@dougbramer4552]

Can you do this without coil split. Stuff. I have same setup. 4 wire pickups. And a three way switch. One volume. One tone.

[@BillLarkinmusic]

Me too!!! HELP PLEASE !!!!!

[@TheWordprophet]

It is basically the same, except the tone pot does not have the DPDT 6-pole connections, and you just tie off the middle pickup wires together (red & green in this video) and tape the end and tuck them away somewhere. (NOT connecting the two pickups to each other - just tying off the middle wires of each humbucker separately) That's all there is to it.

[@schizophrenicdolphinz9822]

William Larkin for people who don’t really know what they are doing it’s confusing to add a ton of unnecessary stuff

[@philipcarroll7151]

So, someone asked for a help with two humuckers with a three way switch and 1 tone and 1 vol (something loads of us have) and you added into the mix a push pull switch and told everyone that unless their humuckers have 4 wires it's not going to work...lol...that's so weird you added your own parameter. Quite a clear demo all the same. Thankyou. Why did you add the push pull switch?

[@johnbanks2275]

what about a jaguar demo with humbuckers

[@danybracho]

Hello, thanks for the video! What if the volume os the push pull pot? Is the same but inverse the volume and the tone connections? Any tip would be helpful

[@matthiassoellner]

Both humbuckers only have 2 wires (1 wire an 1bare wire!) Very good explanation - but unfortunately not for me!

[@krokovay.marcell]

just ignore black and white wires, then it´ll fit...obviously, you won´t be able to split your humbuckers if you only have two wires coming from them.

[@zolar55]

Thank you!

[@oldguy5381]

Could you show me what that drawing would look like with a 3 way tele switch?. Any help would be greatly appreciated, thank you for your time.

[@mpoadmin2978]

if you have to ask please dont even try it. this is what leads to poor wirings and electrical deaths and all that

[@oldguy5381]

@@mpoadmin2978 it’s simple switch change, it’s also a none active circuit so death is off the table. But your answer was good for a laugh.

[@edwardodee2661]

How would you wire 2 humbuckers /1 vol./1 tone and a normal LP switch in a Strat body not using a Push Pulss sw.?

[@Alienadin]

Your videos are great. I can't find one for 2 humbuckers wired in serial parallel, inner and outer coils, etc. using a 5 way super swich slector switch. That would be immensely helpful.

[@tomasmedina488]

Did you find one?

[@firedog9113]

What if I got a humbler and a single pickup. God a sweet guitar and great pickups, is there anyway to do a push pull pick up

[@firedog9113]

Got a sweet guitar I meant

[@creationinspired200]

Literally couldnt have made this more confusing

[@daveogden772]

Wish you had a come picture of the harness nobody does screw up

[@diegoriveira3579]

This is great, but i'm actually looking for a similar config but except with 5 blade switch. Coil would tab in positions 2 and 4.

[@elchivojota]

would love to see this same pattern but with the series/parallel mod just on the bridge pickup-

[@FloydianNM1]

What would the wiring diagram look like if one of the humbuckers only has two wires (Gibson 57’)? Can you wire it so you can split just the one humbucker (w/ four wires) using a single volume and tone knob?

[@sv0205]

Hi tnx for sharing this.......... can u hlp Me my neck pickup is Ok but while plugging guitar only bridge pickup working .... & the nob is Also wrkng How to fix This ....???

[@skipbass2771]

hi,i just got a 80's dean bel_aire guitar has 2 humbuckers 1 volume 1 tone and a mini on/on/on.would would i wire that?not worried about coil tapping just want to use it as a 3 way switch for 2 humbuckers.thanks

[@kevinbrown1833]

Do you have a video for a 2 humbucker, 1 volume and a 3-way toggle. Volume can be a regular pot or a push pull pot. I appreciate your time and help

[@chrisminahan9846]

I need help trying to Find detailed information about Wireing back to factory My Ibanez S 520 EX With 2 dual DiMarzio Humbucker's, With one volume, One tone and a 3 way Selector switch. I just want to wire it back to it's standard Wireing from the factory. Thank you in advance. If you can help me..

[@adrenqlin]

the place where my strings go through, behind that panel there is a single block wire, connected to the place the strings go. it was obviously disconnected from something, but i can’t figure out what! i’ve looked at so many diagrams and NONE show this…

[@DanielColborne]

I think that is your bridge ground wire which should be soldered to the top of the volume pot.

[@p3rc1fernando54]

Can you show us a 2 humbuckers (4way conductor),1 volume, 1 tone, 5 way switch. No push/pull pots. Same as the one Surh did on their Alt T pro with thornbuckers pick ups. Thanks

[@longztar]

Can I use this same method for wiring 1 motherbucker 1 single hot rails with a push pull volume pot and 1 tone pot and a 3 way switch?

[@lithium122003]

Could you make video for 2 Humbucker, 1 Volume, and On-On Mini Switch (Without Selector Switch) ?

[@trevormccann7083]

I thought it said 1 vol 1 tone What's withe the coil split? If I wanted a strat I would have bought one Not looking for coil split

[@davidmurray9193]

I'm using iron gear pickups but no bare wire everything is there but I have a thick black wire and a thin black wire, how do identify which is the north start earth and the bare??????? And the capacitor does it go on a certain way or any way on? I have two guitars to set up one with this set up and the other with two volumes and one cts tone push pull (push pull pots cts on both)

[@Brothersjguitarrepair]

Can you better explain this with no push/pull switch

[@luketanner7638]

Awesome. Now I have no sound output at all.

[@Badrs2810]

What if I don’t want to use a tap coil?

[@adama2562]

does this wiring color scheme work for dimarzio pickups?

[@DougHinVA]

I do not follow what he is saying and to me, it seems he needs to go more slowly and explain just what he is doing and why a bit better. A lot of fellows do NOT know anything at all about wiring in 4-wire humbuckers. So, for example, is A1 the first tab NEXT to the bottom of the pot or the third one?

[@surpk1]

Hi, I don't know if your answering anythiny but same wiring whether or not you have a push pull pot? Thanks

[@Ry_Valz]

Great tutorial! Do you have a diagram having a CRL 3-way pickup selector switch instead of a 3-way Toggle switch?

[@jstro-hobbytech]

What about 3 wire active humbuckers in the same configuration

[@thomasvannatter6361]

Question can I wire up a set of antiquities with braided wire to an only one volume 1 tone

[@markzikosky1588]

i need this same set up with regular pots and 8 pin 3 way switch can u do a vid

[@jasondekemper5476]

That pretty much explains how my PRS is wired.

[@gigiwalker9331]

Hey there, i just followed this amazing scheme but idk if i did it correctly as my 2 humbuckers pickups are Dimarzio a superdistortion for bridge and a paf for neck can someone explain this? I know im a little bit too late as this video was uploaded 8 years ago

[@OBandPL]

Can you get the pups in parallel with one one tone and volume pot? I have push/pull on both pots.

[@CJsFotoArt]

Hi I have a question and hope you can help I purchased a wiring harness for a epiphone special and it was 2 volume and two tone one toggle and a guitar jack outlet, problem is my guitar has 1 volume 1 tone toggle and jack , can I use this harness so that I only use 1 volume and 1 tone and cut the rest out? any videos on wiring this guitar would be helpful no pull up button I have two humbucker pickups switch sits at the bottom between the two knobs.

[@neobonus5864]

Please make HSH 3 way selector

[@0074craig]

do you have a video like this with 2 wires on the pick ups ?

[@evanchristo708]

Will this work with a 2 wire pickup?

[@Stephen_Eee]

I gotta get checked for dyslexia, bc I read comments as 'comunist'.....my real worry is why I clicked on it so fast, lmao

[@milfaby]

2 Humbucker, 2 vol, 1 tone,3 Way, puspull?

[@tannertruong4249]

what if 1 humbucker has 2 wires and the other has 5?

[@witheredmedia]

I have a push-pull pot that I want to wire as if it was a normal pot that didn't have the push-pull feature. Can I just wire it like a normal pot and ignore the 6 extra DPDT switch lugs?

[@todoguitar]

Hi, I have 2 DiMarzio PAF Pro Humbuckers on my Ibanez guitar with a 5-way switch. I took off the Tone and I want to do 2 separate volumes no tone and keep the 5-way switch the way it is. The wiring part is the only part that I'm laking when it comes to guitars I need help :)

[@-Helios-33]

How are you getting two north starts on bridge pick up?

[@-Helios-33]

For anyone with this same question, use a jumper wire. Also had to get a bigger capacitor bc my tone knob was turning off volume.

[@bacohen8]

Hi Don, Is it possible for you to do a video adding a generic onboard effects processor to this configuration but with a 2 single coils on a humbucker platform at the neck (only one of the coils connects to the effect)?

[@tylerclark9322]

Can you make one with 2 single coil pickups, 1 double pickup, 1 volume nob, 1 tone nob, a switch and input

[@BenjaminVallejera]

Hi! Question though, how do you wire a 2humbucker, 1 vol, 1 tone (push pull) no selector switch? (i.e. the tone will select 1 of the humbucker. not using both). thank you in advance!

[@spencerwarren9219]

Yes I dont have a spit coil. No body uses those on humbickers. Why would anyone one that crappy buzzy single coil tone

[@miamiroadcyclist9579]

Can I get 8 different pickups positions using a Volume Push/Pull Toggle, plus a Tone Push/Pull Toggle and a 3 way switch ? DO YOU HAVE ANY DIAGRAMS OR VIDEOS HERE IN YOU TUBE ???

[@johntrip07]

Anyone have a diagram for 2 Humbuckers/3-Way Toggle Switch/1 Volume (no tone)?

[@thatrato]

Honestly good luck with that man, im struggling myself finding 2 humbucker/3-Way Toggle Switch/ 1 vol/ 1 tone without push pull and cant find it anywhere

[@oudaijawad5809]

Do you have dual Hum with 5 way switch toggle 1 volume 1 tone push and pull

[@darwinrucker8488]

What do you mean by solder the wires together?

[@glytch5]

Seems like when manufactures wire guitars there are tons of extra ground wires all over the place.

[@meyeshots3426]

Just have the same thing here with my LTD EC-256

[@AxleGunnactorandvoartist]

thank u for this video, just one question. re the A3 lug re the red n green wires.. where do the red n green wires goon a standard non push pull pot?ie is it one of the lugs on the tone pot?

[@stratacaster55champ]

What value compositor are you using?

[@molinamusic5110]

Hey bro you have a video same but with a 3 way switch?

[@BisonWorkshop]

can you please do this without the push pole switch.

[@manny75586]

The wires he attached to the push/pull can be soldered together at their ends rather than to the push/pull. Then wrap the joined end in electrical tape or some electrical supply stores have tubing you can shrink wrap around the end if you want to get very fancy. It's just important for neither of those wires to be touching anything but one another. Look up the wiring diagram on the manufacturer's website to make sure you have the right ones.

[@ivanasin1268]

Thanks for this video. Question: can I set this up in a way that I can also choose the inner coils ?

[@ericsanders5357]

Diary feel?...I can only imagine the what kind of emotional wreck you must be,..here let me fix-the world owes you(me, or anyone else) anything...you're welcome.😉

[@anthonya.p.dellaquila8183]

Excuse me. What writing is that on your youtube account name and videos. Thanks

[@rodmills6750]

That is a four wire pickup.

[@dikdikmulyadimulyadi1755]

how to kabel brige two cabel.midle twi cabel and neck two cabell...??????

[@paulk.bowden7134]

Looking for a duel 2 wire Humbucker, single volume and single tone wiring schematic.

[@theorncampbell4432]

Go to Seymour Duncan's website. They have schematics for most configurations, just no push-pull kill switch set ups. www.seymourduncan.com/wiring-diagrams?__uuid_ref=5a87c2044ddac

[@woofystevenson2943]

Theorn Campbell push pull kill is easy, jump the bottom two lugs 5 and 6 and then do input lug 3 and output lug 4

[@kevinintong7664]

is this dimarzio or seymour duncan ?

[@spencerwarren9219]

For the record I hooked my two humbucker up with my volume and tone pot exactly to the T this was and nothing did not work. No signal

[@russoBLT]

I really need your help friend! plss

[@guitarpro594]

You should really give the credit of the video to the rightful owner *Berja Toneworks* instead of posting someone's intellectual property without permission like it is your own..