Duracraft 14'x36" Jon boat jack plate / setback bracket installation

  Рет қаралды 51,717

Slab4x4

Slab4x4

Күн бұрын

Пікірлер: 38
@seychellesnews
@seychellesnews 9 ай бұрын
Thanks for them internet videos you make Billy Bob, really be helping us water folks
@6Alpha-yankie_novemberdy2n
@6Alpha-yankie_novemberdy2n 6 ай бұрын
Installed a 75 Merc on my 14ft Mon Ark. Had to do the same, except i used a set back with riser for South Carolina swamp's
@nicholasboyd7658
@nicholasboyd7658 2 ай бұрын
Will you run the motor with the breakaway open also or since it’s on a kick plate will you keep it latched? Thanks
@mvboutdoors
@mvboutdoors 2 жыл бұрын
How did this affect the weight balance? Any issues with it? Im looking to move my motor back a few inches for the same reason but I didnt think I'd need a 7" setback but yours looks good.
@slab4x477
@slab4x477 2 жыл бұрын
Hey thanks for watching! I haven't had any trouble with mine so far. I do have 2 12v batteries behind the front seat so that helps when I'm using the outboard solo. Vance does make a 5" version and I'll attach the link for you, this one is up to 20hp www.vancemfg.com/5inch-setback-mini-jack-plate-p/jpl2410sb.htm
@mvboutdoors
@mvboutdoors 2 жыл бұрын
@@slab4x477 Good to hear, thanks for reply! I'm trying out a 2.5" setback to start, going to see where that gets me.
@mjones529
@mjones529 2 жыл бұрын
I just bought the same jack plate you got. Instead of installing the transom support brackets horizontally, I wonder if I can install them vertically?
@slab4x477
@slab4x477 2 жыл бұрын
Nice! I dont see why you couldn't, it should work. Thanks for watching!
@c.shoefish
@c.shoefish 3 жыл бұрын
Could you post the measurements of the bolt holes? Like how far apart they are horizontally and vertically. I'm trying to determine if they'll at least come close to my existing holes...thanks!
@toddthames8326
@toddthames8326 Жыл бұрын
Hey I know this thread is 2 yrs old , but I'm from south east ga to and I'm redoing my jon boat as we speak , and running into same problem with the motor to close to seat , how do you like that offset bracket? You still ok with it ?
@royalroachs
@royalroachs Жыл бұрын
Does the motor get in the way in adjusting the bracket up or down?
@slab4x477
@slab4x477 Жыл бұрын
Yeah some.. smaller engines I'd recommend unclamping to adjust. Its possible to do it while clamped on.
@CC-xs1hh
@CC-xs1hh 4 жыл бұрын
Do you have any advice on where I can find T-slot bolts for accessories like rod holder , (mainly)Bimini top brackets, etc, I haven’t had any luck , I even called Duracraft....thanks for any help.
@slab4x477
@slab4x477 4 жыл бұрын
I wish I did.. I haven't been able to find any either. It would be nice to be able to actually my rails
@ericrhinehart5434
@ericrhinehart5434 3 жыл бұрын
Easy, go on any site that sells t-slot bolts for machinists, etc. in fact amazon will sell them ...in many cases regular bolts can be used also.
@slab4x477
@slab4x477 3 жыл бұрын
@@ericrhinehart5434 I dont think mine is a T slot. Swivl-eze make a sliding seat bracket. My slot is kinda like what the actual seat bracket would fit into. If that make sense
@gavinbullock6521
@gavinbullock6521 3 жыл бұрын
I’m having a problem with water coming in the boat Bc of the motor, would a jack plate help? It won’t get on plain right now
@tylermelloy4
@tylermelloy4 3 жыл бұрын
Yes, you need to lift motor 5 inches with a jack plate and you’ll be good to go
@slab4x477
@slab4x477 3 жыл бұрын
Yes, you need to lift it some. I highly recommend Vance
@ASMRWandering
@ASMRWandering 2 жыл бұрын
Where did you find those transom support brackets?
@slab4x477
@slab4x477 2 жыл бұрын
I went to my local Lowe's and got some flat aluminum and made them. Thanks for watching!
@backwatermcfly7930
@backwatermcfly7930 3 жыл бұрын
How’s it run on the river can you get in shallower water?
@slab4x477
@slab4x477 3 жыл бұрын
It has ran great for me. No problems yet! I had all intentions of making more fishing videos after this.. I even had unedited footage with some nice Redbreast fishing. Just got busy doing some side work and never did. Thanks for the comment and I'll be back at in the spring with more content.
@Spikexphil
@Spikexphil 3 жыл бұрын
Is that the 1 inch clamping board on there? Hows it hold up?
@slab4x477
@slab4x477 3 жыл бұрын
It's one that I made out of synthetic deck board material. Haven't had any trouble with it yet.
@Spikexphil
@Spikexphil 3 жыл бұрын
@@slab4x477 Gotcha, the one from VM is the same material I was curious. Getting the 5"setback for my merc 9.9 2 stroke.
@jorgeperez4930
@jorgeperez4930 Жыл бұрын
Buenas que tal, y mejoro el rendimiento el motor, cuanto?
@tangerineRIDES13
@tangerineRIDES13 4 жыл бұрын
Skeet a big rooster down the gechee river Yee Yee!!!
@slab4x477
@slab4x477 4 жыл бұрын
She's ready!
@mrGW
@mrGW 3 жыл бұрын
Never seen goldplated nuts like that before😍🤔
@slab4x477
@slab4x477 3 жыл бұрын
They came with the plate from Vance. They are locking nuts
@kodybaker9635
@kodybaker9635 4 жыл бұрын
Do you have a link to that jack plate
@slab4x477
@slab4x477 4 жыл бұрын
www.vancemfg.com/7inch-setback-mini-jack-plate-p/jpl2710sb.htm
@indianapublicland7429
@indianapublicland7429 Жыл бұрын
did you gain any speed being able to raise it up?
@tonysimons7218
@tonysimons7218 7 ай бұрын
Would have been easier to move the seat over to the right a bit .
@slab4x477
@slab4x477 7 ай бұрын
Yep, but I have been in boats like that and do not like off centered seats.
@tonysimons7218
@tonysimons7218 7 ай бұрын
@@slab4x477 I turn sideways when driving anyway and out my feet on the rail . More leg room.
@danielthrasher2332
@danielthrasher2332 2 ай бұрын
Should had changed that wood on your transom before you put that jack plate on kill two birds with one stone🤠
NEW JON BOAT JACK PLATE 🤔🤔🤔”Vance Manufacturing "
24:54
Hollis Farms
Рет қаралды 62 М.
5 Jack Plate Facts You Should Know
6:01
T-H Marine Supplies
Рет қаралды 89 М.
SISTER EXPOSED MY MAGIC @Whoispelagheya
00:45
MasomkaMagic
Рет қаралды 19 МЛН
бабл ти гель для душа // Eva mash
01:00
EVA mash
Рет қаралды 3,8 МЛН
Bass Boat Jack Plate Replacement Walk-though (18ft Fiberglass Boat)
15:48
Jenkins Bass Fishing
Рет қаралды 64 М.
Jack Plates Low to High @ontheflyjackplates875| Budget boat build Ep.9
14:41
FWB As the Screw Turns Episode Three "Jackplate Testing"
13:55
Rocky's Roads
Рет қаралды 41 М.
How to Mount Hydraulic Jack Plate on Your Boat
4:39
Florida Sportsman
Рет қаралды 13 М.
Hydro Turf Installation
11:33
Sportswoman Courtney
Рет қаралды 179 М.
Youtube's Best DIY Jack Plate for Small Outboards Jon Boat - OOW Outdoors
26:41
I Finally Purchased A Jackplate!!!
7:04
ThatBoatGuy
Рет қаралды 829 М.
Super Simple Jon Boat Floor
12:48
Anthony Jones
Рет қаралды 622 М.
SISTER EXPOSED MY MAGIC @Whoispelagheya
00:45
MasomkaMagic
Рет қаралды 19 МЛН