DUT-E 485 Fuel Level Sensor Installation

[@trevorrasekaba6723]

Good day! I wanted to know the specific size of the hole saw used to drill for the sensor

[@TechnotonEN]

Good day! Hole diameter 39 mm.

[@kamalakannansubramaniam3727]

Very nice presenting the explanations.

[@mr.write1433]

Does it have a normally closed contacts or open ? is it applicable for gen set specially for the external pump

[@tumusiimebrighton6529]

Hey am to install a DUT E is the orange wire always brown wire always connected to the ground or it is some times change the colour code

[@TechnotonEN]

Hello, our technical specialists will help you with the connection, write to [e-mail]

[@AlexSBedini]

Hi I am installing the DUT E AF tomorow, can I ask if calibration through SK DUT E kit is necessary for this FLS to work properly?

[@ojwekegeorge7576]

On tractors is it possible to use CAN BUS to read fuel?

[@TechnotonEN]

If there is fuel data in the CAN bus of the tractor, it is possible.

[@atsplsalesbelgaum993]

what if we drain below 5 ltr? do we get results?

[@TechnotonEN]

Hi. Thank you for the question. Yes, you'll detect that. DUT-E sensor's measurement step is 0.1mm. That means, if you have 1,000 liter fuel tank, which is 700 mm high - the sensor detects ~0.15L fuel change. But accuracy hugely depends on fuel tank shape and precision of calibration. Please, contact us for further information jv-technoton.com/contacts/

[@alsavage1]

The DUT-E Operation Manual says that the probe is to be installed (in most cases: shortend/cut) to no less than 20mm above the bottom of the tank, (page 29). That means the effective measurement range does not include that bottom 20mm, and they actually specify 20-30mm. Depending upon your tank volume and shape, it's may or may not show any above-empty reading for your last 5L capacity.

[@Stunningmotionsdigitalagency]

What is the price of this digital sensor. We are looking fuel monitoring device in Pakistan having features like sms alerts, report generate over consumption and when engine stops.

[@adnanmusic5931]

Which is diferences between analog and digital sensors and which sensor is better for usage

[@JesusParrafull]

Hello Adnan, there are a big difference between the analog sensor and the digital sensor, the analog sensor provide the information in voltage (so you need a device with an analog input to read this information) and the digital sensors provide the information through the interface RS--232 or RS-485... Here is the operation manual, hope it helps you!.. www.jv-technoton.com/data/dc/DUT-E_SK_DUT-E_operation_manual.pdf

[@adnanmajeed6178]

Digital is the best

[@samramusic8541]

Why?

[@nicholasanjiri4782]

can fuel level sensors fitted in petrol station tanks? Or its only meant for small tanks like those on vehicles.

[@latemakgroupe846]

Yes it can fit in petrol station tanks

[@amazingsite2581]

Could you upload the FUEL LEVEL SENSOR INSTALLATION GUIDE specially DUT-E S7? I have received the sensor but there is no installation guide yet

[@TechnotonEN]

Hello. You can download the manual for the sensor in our document center: docs.jv-technoton.com

[@murugesan494]

Hello Lenon, I hope you are fine, I need to know, have you appointed any dealer for your product in India (especially in south India), please update.

[@tonydavis4576]

You probably dont care but if you're bored like me during the covid times then you can watch pretty much all the new movies and series on InstaFlixxer. I've been streaming with my gf for the last couple of weeks xD

[@jaxxanthony5350]

@Tony Davis yea, I have been using InstaFlixxer for since november myself =)

[@mouniroldmhb3056]

How can you sent me all the system to Algeria please

[@TechnotonEN]

Hello, please write to us at [e-mail]

[@jameskazimoto6823]

how do i connect to the actross benz

[@vyryx]

salut cum fac sa scot motorina fara sa stie acest senzor?

[@ivo.sinapov]

Hello, Why the fuel level in mm. at the last filling goes more than the cut length ?

[@aanpilogov]

do you mean readings of 530.4mm at 18:50?

[@gopichandkunamaneni5790]

What is the drill size?

[@TechnotonEN]

Hello, the hole will be 39mm in diameter.

[@rinaldopastelli7749]

On barges is it possible?

[@TechnotonEN]

Hello. Yes, this is possible, but we recommend that you take a closer look at the fuel flow meters. You can get more detailed advice by writing to [e-mail]

[@Ahmedi1234]

Very good but mistake you made you didn't show us how to set leve,s and ather,s by diagonals or computer??

[@TechnotonEN]

Thank you for your comment. Have you purchased our sensor? You can write to us in support at [e-mail], you will be advised on this issue.

[@ghanshyambhaiakhani8299]

Fual leave installation charges?

[@TechnotonEN]

Hello. Please send your request to [e-mail]

[@rock4us2]

Is it the same as the DUT -E 232 fuel level sensor?

[@TechnotonEN]

DUT-E 232 is designed to work with RS-232 interface, and DUT-E 485 with RS-485 interface. That is the main difference. They are quite similar. The Manual can be helpful if you need in-depth comparison: www.jv-technoton.com/data/dc/DUT-E_SK_DUT-E_operation_manual.pdf

[@rock4us2]

Thanks Technoton EN for your reply. We are trying to configure the RS-232 sensors in pair to work with a Mix Telematics Fleet Manager Communicator goo.gl/uBRZXS unit but we are failing.

[@TechnotonEN]

Lennon Emmanuel I have forwarded this information to our support team. Please leave us a contact email so our specialists can get in touch with you.

[@rock4us2]

Technoton EN i will inbox you my email adress

[@rock4us2]

i cannot find the inbox option Technoton EN my email is [e-mail]

[@adnanmajeed6178]

Hi, Same procedure for RS- 232 ?

[@sergeyp1280]

Yes, the procedure is the same for RS-232 and for other interfaces.

[@upparahalsomashekar8247]

@@sergeyp1280 where it is available?

[@sergeyp1280]

@@upparahalsomashekar8247 Please write your inquiry or questions to [e-mail] and you will be provided with all required information.

[@galihwibisono9785]

How to check the data?

[@TechnotonEN]

DUT-E is used in GPS tracking as additional fuel sensor or as a replacement of standard built-in (factory) fuel level sensor. Information on compatibility of fuel level sensors DUT-E and tracking device: www.jv-technoton.com/compatibility/

[@kalaiselvan2404]

How much price sir

[@TechnotonEN]

Hello, please tell me your e-mail. Our manager will send you all the information you need.

[@sghauri2]

I LOVE U GUYZ WELDONE

[@deepeshenterprisesvivekmis4597]

Nice

[@himanshudipanshu4330]

Rs

[@TechnotonEN]

Hello, the price depends on the model characteristics. Email us at [e-mail]

[@mirjaafrozbaig7961]

Sir paric

[@TechnotonEN]

Hello, thank you for your interest in our product. The price depends on the model characteristics. Please, email us at [e-mail] for product consultation

[@decencydecorum]

too much background noise causing headache

[@mouniroldmhb3056]

How can you sent me all te system to Algeria please ?

[@TechnotonEN]

Hello. Please send your request to [e-mail]