E-flite Extra 300 3D 1.3m Assembly

[@gregmcgee4430]

Ok, I was crying on that tail feather!!!!

[@haydenshores9943]

Thanks man you helped me get back into it after a few years appreciate it gonna be the plane i get

[@sams0748]

Really nice collection all my favourites

[@hondarobin]

very nice good job i like this

[@BALAZSER1]

Thank you very much

[@haydenshores9943]

Hey a question it sais 4 minute run time but how long would i get off a 4s 2300 mah going somewhat conservative on the throttle

[@BALAZSER1]

I don't know it depends on the wind and how heavy on the throttle you are.....

[@ClaudeFrancois-f2t]

what do i you have the servo arm set at for aileron, rudder and elevator?

[@BALAZSER1]

It's factory settings

[@ClaudeFrancois-f2t]

@@BALAZSER1 i compared to throw to what they should be in manual and they dont match. i measured the angle it recommended for high rate and low rate the rudder and aileron do not extend as far as what manual recommends

[@BALAZSER1]

​@@ClaudeFrancois-f2tYou might have to call them😢

[@ClaudeFrancois-f2t]

@@BALAZSER1 need help when I do range test ar631 receiver after 25 feet signal lost and then comes back and everything moves slowly aileron rudder etc I loved the antenna still no luck on range test when near plane 10 feet all perfect

[@BALAZSER1]

​@@ClaudeFrancois-f2twww.rcgroups.com/forums/showthread.php?2933500-Spektrum-signal-loss

[@kellysweetman6070]

Thanks for the video. I've got a few planes from eflite. (P-47, J3 Cub) both went together very well and they fly great. I'll be ordering the Extra next week. I'm sure it's going to be a great addition to my smaller foamie collection.

[@BALAZSER1]

Awesome!! They are great planes!! I hope you enjoyed!!!!

[@corsairusawc]

I like your area, its nice and organized

[@BALAZSER1]

Thank’s!! My table is, but my hanger is a nightmare, everything has been moved everywhere, because my neighborhood had a flood a wile back😪. I’ll get it all back in place sooner or later 🤪

[@Channel-tr1hx]

finally a foam airplane with removable / clean replacement of the stabilisers. seems well put together

[@BALAZSER1]

It's amazing for the price!!!

[@noamholland5020]

If I want to change the receiver is it possible? for the extra 300

[@BALAZSER1]

You can, but, I would just use the one it comes with.

[@noamholland5020]

@@BALAZSER1 ok thank you sooooo much

[@gisall8205]

Great video. Question. Does that Aileron " Y " Harness come with the kit. Horizon will Nickel and Dime their customers to death every chance they get.

[@goode426]

Thank you for for your time and very helpful video. I bought recently but a newer model (red Swiss watch) beautiful plane(:

[@BALAZSER1]

Your very welcome, I was hoping it would help someone👍👍. Somebody complained that the video was too long, but that's how long it took me to put it together lol🙂. That's awesome you got one, congrats on getting a awesome airplane !!!👍👍🤗😎. Do you have any video of it on KZbin of it?

[@goode426]

@@BALAZSER1 No, I have not ever made a video that would be a whole new class for me lol!

[@BALAZSER1]

goode426 It’s not hard, I bet you could do it easy👍👍. I hope your flight goes well, and you have many fun flights with your new plane😃👍👍

[@dwproductions5172]

Very helpful video. I would recommend a stand so you can flip the model over and we can see what you are doing on the bottom of the plane, mainly when you were installing the elevator/rudder links.

[@BALAZSER1]

I don't know why, but youtube flagged your comment as spam?? I approved it : ) Thank you for the comment, next time I do a assembly video, I'll try to do better. Thanks for watching, and I subscribed to your channel!!

[@dwproductions5172]

@@BALAZSER1 That is odd. Maybe I'm a trouble maker and just don't know it. Just watched your CG video, good stuff buddy!

[@BALAZSER1]

DW Productions Yeah it was, that rarely happens🤔. Thanks bro, it has been raining here, I needed to get the CG down anyway, and it's not the kind of thing they go over in the manual!!! Thanks for checking it out🙂🙂👍👍

[@strykerf27q1983]

I cant believe how fast you put this plane together. I had major issues with screws lining up and had to glue half my elevator on and I had to tear a wing out after I missed the screw holes and the screws got stuck in the foam in those recessed holes took me about 10 hours Lol. Flys Great stable but very responsive tons of power but like people are saying it doesnt prop hang as well as my ultimate 2. or maybe i just have to get used to it.

[@BALAZSER1]

strykerf27q1983 I had a little problem lining up some holes as you can see in the video, but wow, nothing like what you had!! It will prop hang, but you have to find the sweet spot, and that's not so easy lol!! If you want it to prop hang more easily, you have to add some tail weight slowly until you get it to your liking. I'm still experimenting with tail weight myself : ) I happy you got it together, it sucks that it took 10 hours, but sounds like you got it flying great!!!

[@strykerf27q1983]

Thanks man and yeah it took less then 10 Hours more like 3 but still just as bad it felt like 10 hours thanks for the info on the tail weight. I'm really liking this plain I'm running my f 27 batteries which are 2200 4 cell timer set to 7 minutes cuz im not sure but I'm going to get some 3200mah. You must be getting 10 minutes with those?

[@BALAZSER1]

Ok cool!! Yeah, always feels like a long time when your ready to fly right away lol!! When I use my 2200 4s, I only fly for 4 minutes, because I flew for 5, and puffed a battery lol!! On the 3200 4s, I still only have flown for 4 to 5 minutes, but when I test how long it can fly on the 3200, I'll let you know!! The 2200, is way lighter, so you can throw the plane around more, but the 3200, balances the CG of the plane out more, so it' give, and take!! : )

[@gregmcgee4430]

Glad you dry fit that rudder. Not hating but good advice.

[@strykerf27q1983]

Great video I can't wait to order mine and after watching this I can see horizon put the heavy hinges on the rudder where there needed and probably used lighter ones probably the same kind as like in the stryker for the elevator with are plenty strong. Im not sure why guys where having issues but thanks for helping me decide that this planes for me.

[@BALAZSER1]

Thank's!! Someone complained about it being to long, but I just told them that's how long it took me lol!! I think its plenty strong too! I don't know why people are having issues either, but I haven't had any!! Your very welcome, and I don't think you will regret buying it, I know I don't!! Let me know how it goes!! : )

[@strykerf27q1983]

Thanks yeah I'll let you know.😀

[@BALAZSER1]

Cool👍

[@sternslaptop]

How tight did you make the wing bolts? I just built mine and was wondering how hard to crank them

[@BALAZSER1]

Only till it stops, If you go any farther it will strip.

[@revedicare1230]

Bonjour Dans quel sens doit on monter l'hélice ? Mer pour apporter votre réponse

[@BALAZSER1]

Thank you for checking it out!! I wish I knew what you were saying lol!!!

[@kimmvydareny8771]

@@BALAZSER1 He said, "In which direction should the propeller be mounted. Thank you for your answer".

[@Thebankfisher]

Does this have that stupid slide in battery tray?

[@BALAZSER1]

No, just straps!!

[@Thebankfisher]

@@BALAZSER1 I had one for a few months since that comment ..it was my favorite plane until I crashed it ....I got to comfortable just stick mashing lol they fly really good though

[@BALAZSER1]

@@Thebankfisher Dang!! Sorry to hear that you crashed it!! I'm sure I will fubar mine a some piont!! I came close the other day, clipped a powerline exploding the prop lol!! Don't know how but still managed to dead stick land. Sucks I wasn't shooting video : (

[@firstjayjay]

just got mine home and started putting it togeher following your vid. The glue, was the included in yours? or is that something everyone is expected to have lying around?

[@BALAZSER1]

john rosenskjold Glue not included lol!! Any RC hobby shop should have the glue. I use Zap-A-Gap Medium CA+, and Zap Zip Kicker CA Accelerator to make it cure super fast.

[@firstjayjay]

4:00 i spent about the same time fiddling with that damn screw

[@BALAZSER1]

john rosenskjold Lmao!! That screw was getting on my nerves lol....

[@jasonsitz3056]

I was trying my best to see how you put the tail will in because mine went through the styrofoam can you take a picture of the back tell Will and how it was assembled please I washed your whole video and your cameras on your forehead and you can't see what your eyes are seeing

[@connecticutgunner9333]

Would have been much better if you explained things as you went along.

[@BALAZSER1]

Yeah!! My bad!! Next time, I will!!

[@budmartin8297]

Thanks for calling this an assembly. You can't build an ARF, you can only assemble it.

[@BALAZSER1]

No worries, I'm glad you liked it👍

[@HighlanderJC]

video way too long

[@BALAZSER1]

Sorry , that's how long it took me to build it, was just trying to help others who might get the Extra 300. I have other videos you might like on my channel that are not long👍👍 I'm not on KZbin to try to make money off of it, all just for fun! Here is a short video! 1:30 seconds funkzbin.info/www/bejne/eILCi3x6oaaBqJo