Easiest Bike Crank Bearing Removal

Рет қаралды 79,461

Mechanic Vance

Күн бұрын

Пікірлер: 32

@AntVandura 2 ай бұрын

I'm a former Army mechanic and totally forgot about the old hammer trick. Thank you.

@mechanicvance2480 2 ай бұрын

Yeah, sometimes the inertial impacting device is needed….they never let us do that in the Air Force 😉, must be the country in me haha.

@AntVandura 2 ай бұрын

@mechanicvance2480 Thanks for reminding me of its technical name. For the record, the Army allowed us (when no one was looking). 😆

@fabioaloise Жыл бұрын

Hi. Nice video! Please I have some questions that you might help me with. I have a Schwinn Santis and the bottom bracket looks a lot like this one. 1. Is this bike in the video also a Schwinn bike? If so would you know if this uses the same bottom bracket of a Schwinn Santis? 2. What is the internal diameter of the bottom bracket housing on the frame of the bike on the video (where you screw in the bottom bracket itself)? 3. I believe the Santis also uses a non sealed bottom bracket. If so, I would like to replace mine with a sealed one. Please which Shimano sealed bottom bracket part would you recommend? 4. Do you have the link to the tool kit that you mentioned from Amazon? Thank you very much for your time and support! Fabio

@dalebenton3354 Жыл бұрын

Thats the next repair to do on my E bike,Got to take the whole crank out,Replace the ball bearnings and the chain,Also check through the whole bike,Getting it cleaned up,Be fully service repaired,Just replaced the both innertubes and tires on it,Glad no longer putting up with any more punchers

@bestmoments7993 11 ай бұрын

How did you replace the paddal I need help with that

@nodafy 10 ай бұрын

Be careful with E bikes, they can get quite fiddly with the motor

@dynoshane2651 4 ай бұрын

Does that last big bearing nut always turn anti clockwise ro loosen? I'm having major drama with it slipping off the teeth.

@sandraramroop5864 5 ай бұрын

Helped so much thanks

@krakqs5385 18 күн бұрын

What to do if bearing is loose and is falling out? How can i tighten it? Its almost as if bearing became too small od something, this ring that tightens on doesnt really help

@mechanicvance2480 15 күн бұрын

If its the bearing that came with the bike then its probably worn out or missing some ball bearings. Take it out and look at it really close. I would replace it either way, if your questioning it and your that far in why chance it. Hope that helps.

@jesserenee6948 9 күн бұрын

Thank you!!!!!

@mechanicvance2480 8 күн бұрын

@@jesserenee6948 glad to help, if you have to do this I would buy the kit….even today.

@markwelllynn92 8 ай бұрын

I have a plain walmart schwinn ranger, the bearings were ate up in nothing left. How do I know what size to get, the model # calls for a 12 bearing but I can't seem to find one.

@johnperez4537 10 ай бұрын

Belize ya I try to make that gaged to remove crank arm

@mohamedakhbi3580 7 ай бұрын

Thanks

@TheFlaminFire888 2 жыл бұрын

Was it easy replace all the items back into place? Do new bearings slide right in easily or do they need to be pressed in?

@mechanicvance2480 2 жыл бұрын

Everything just goes back in the order you take them out, no pressing required. The crank arms are pressed on by the crank arm bolt when you tighten it, after a ride around the block they will probably be due another tightening.

@antonio40125 2 жыл бұрын

Wat is name of wrench to remove outer ring ?

@nunyatd Жыл бұрын

@@mechanicvance2480 not if it's done correctly. You also have to make sure you use bike bearing grease in the casing where bearings are held. Put back together tight and it will work fine. That's what I have always done. Buddy forgot to mention this.

@Outty68 Жыл бұрын

Great video. Where did you find bearings to replace the old ones?

@nunyatd Жыл бұрын

I have always took the bearing out of old mountain bikes people have thrown away. 99% of the time bearings and casing are in perfect condition I don't no what this guy does😁