Easy CNC with SINUMERIK Operate Part 1 ShopMill setup and programming

[@ammaskp5063]

Very good morning sir 🙏🌺 well done sir 🙏🌺

[@ammaskp5063]

Super 🙏 good sir🙏

[@maheshpatil480]

Good sir,please make videos on shaping gear teeths and on hobbing process

[@Avalerin80]

do you have sinumeric 4,7 before choosing machine and which you choose video? and later this ?:p can't figure out which machine is this..i have demo only..maybe that's why

[@alexanderkudinov1025]

This video has been made on Sinutrain 4.5

[@raghurao6797]

Hi sir please make video on how to create custom screen in CNC system

[@alexanderkudinov1025]

Send to me the e-mail and I send to you instruction

[@raghurao6797]

@@alexanderkudinov1025 send me your email address

[@swapnilkotrange3359]

Thank you for detailing

[@Avalerin80]

you use sinutrain? if yes which machine i should set on start up?

[@alexanderkudinov1025]

milling machine, if you want use the milling technology

[@lfnvrnds9069]

Mr. Kudinov do you have a lot of experience with the 828d control? If so any chance I could speak with you directly?

[@alexanderkudinov1025]

LFNVRNDS hi, I have some, how can I help you?

[@lfnvrnds9069]

Brand new control and terrible support. Looking for I believe simple questions answered like proper way to home tool changer to start loading tools and some simple questions on writing a new program at the machine. If you think you can help me out with some simple start up questions, can we get a direct link conversation going?

[@craigaseddon]

Does anyone know how to run an NC program without the axes juddering in milling, it's not the NC program as we can run the program on a hurco without any problems. There must be some settings on the control to allow maximum through put.?

[@alexanderkudinov1025]

it might be a problem with mechanical parts of the table or Kv,Kp factors. Or the problem in the program, could you show the head of the program?

[@Parfen_Rogojin]

I cannot realize, is that low-digitized sound a part of Siemens policy? It's slightly strange for such serious company.

[@alexanderkudinov1025]

Excuse me, but this is not Siemens channel, and the quality of the sound is my fault, I am not an expert. If you want I can provide to you a link where you can listen the original video. Should I?

[@Parfen_Rogojin]

Yes, please. I haven't found.

[@alexanderkudinov1025]

here you are - www.industry.usa.siemens.com/topics/us/en/cnc4you/Pages/Webinars.aspx

[@Parfen_Rogojin]

These seem a little better. Thank!

[@littlestworkshop]

Much better!

[@nerwusek19]

Hello , can you tell me how to deactivate spindle positioning on Sinumerik 808D turning ? I can activate it by using SPOS comand and its working until I move chuck by hand or by use M3 or M4 spindle rotation, there is alarm that spindle position is lost.Is there any comand to deactivate SPOS? Spindle position icon in degrees is on screen under Z and X position.Only way to deactivate SPOS is to send both Z and X to home position, and than when I came back to JOG there is no SPOS icon on screen any more...

[@alexanderkudinov1025]

what if to use M19 instead of SPOS?

[@nerwusek19]

@@alexanderkudinov1025 I did tried M19 friend...and no result.That was my first thought, maybe there is kind of comand like SPOS=OFF or similar

[@alexanderkudinov1025]

@@nerwusek19 I will check the Docu and let you know, tell me what do you want to reach?

[@nerwusek19]

@@alexanderkudinov1025 I want mount simple drilling spindle bt30 with drill bit 15mm with 1kw induction motor and mount servo spindle motor 7.Kw with servodrive and braking resistor.Original spindle motor is 7.5Kw induction motor.Mestake I cant deactivate SPOS untill I will turn off all system completely , and turn on again, homing is not helping, so its impossible to run program with drilling without restarting all system...:(

[@alexanderkudinov1025]

@@nerwusek19 what about encoders? Do you have one on the mechanical system?

[@Avalerin80]

23:59 you called it top of the Part..i have HA not ZA :/ Language differences ?

[@alexanderkudinov1025]

No, it should be ZA

[@Avalerin80]

Why i Have HA not ZA ? its diffrent ?:(

[@alexanderkudinov1025]

What do you mean said HA and ZA?

[@Mr1bassman1]

Please move the cursor slower, it is really difficult to follow

[@danielpatrick7992]

Very irritating sound quality :(