EASY DEWALT CHUCK REPLACEMENT WITH NO SET SCREW.

[@nasa7886]

Absolute perfect and easy to follow video. Just saved me from buying a new drill. Did it in ten mins. I couldn’t insert the Allan key as the chuck was totally broken and would not hold anything. I held it as tight as possible in a vice and cracked open the shaft with a spanner. Hey presto it came off easily. Thank you for uploading 🫡

[@pettchucos2769]

Hello I'm from Brazil, it was very easy to remove the chuck with your explanations, thanks for sharing your knowledge. The model I exchanged was the DCD 796.

[@David-dz8jb]

I was a little sceptical about the prising off the Chuck but low and behold it came off fairly easily and I got the shaft unscrewed as pictured there are more complicated ways shown on ytube but yours is by far the quickest I’m just waiting for a replacement Chuck to arrive now. You have saved me from getting a new drill. Thanks

[@DoItWithDave]

Nice work! Thanks for watching!

[@DaveLeemans]

I had a chuck that was screwed from day one. This worked even smoother than your video shown. Thanks for the video.

[@DoItWithDave]

I'm glad you found this video helpful. Thanks for watching!

[@davidkelly7716]

Thanks so much - like the other folks I had exactly same problem with my DeWalt DCD795. You method worked a treat and have saved me an expensive repair or a new one - there's nothing wrong with the drill itself, thank you Sir. Great video.

[@DoItWithDave]

Thanks for watching!

[@rickyrickharris4908]

David Kelly iv got the dcd795 also. Iv got a bit stuck in chuck and chuck is stripped. Jw its will wrk the same way with out 795 as shown in this video?? And a question for both of you guys, can ether of you give me a link to the chuck i need th purchase? Agin iv got the 795. Thanks fellas

[@davidkelly7716]

@@rickyrickharris4908 Hi Ricky sorry for delay. So I'm in the UK and I managed to get this De Walt DT7012-QZ chuck which has worked brilliantly and was super easy to install onto my drill. it's a lot heavier than the original chuck so it kinda behaves like it's in hammer mode most of time, even drilling timber but it's fine. Works great - hope this helps

[@LaserLes-c9o]

Watched other methods, which look violent or complicated. Tried this way and had the new chuck on in 20 Minutes ! PERFECT !

[@DoItWithDave]

@@LaserLes-c9o I'm glad you found this video helpful. Thanks for watching!

[@setzutokugawa2588]

Este método también se puede con el dcd805 ​@@DoItWithDave

[@kerrypickton5968]

Best video ever , followed instructions and worked perfectly, had to wet sand the shaft and light machine oil to reinsert for spring to reseat

[@chrisscott8829]

I read a lot of more complicated methods of dismantling the unit but thought I would give this a go although I was not confident that prising off the chuck would work but it all worked perfectly exactly as shown in video - replaced the chuck and the drill works like new....Thanks

[@dekurvajo]

Ok, this is looks doable. You gave a huge favor to DeWalt. In think they are too ignorant or arrogant to admit that this kind of design held back a lot of people to buying these "screwed" models. By watching your method i might change my mind and buy one of these.

[@msk3905]

I used my DCD 980 to mix thinset and sure enough chuck froze up so need to replace it, i watched countless videos on how to replace and hope this works. Going to get the same chuck you used, this exactly why i come to You Tube even with the annoying commercials! Thanks

[@persona250]

GENIUS thank you i managed to remove one today using this method

[@doctorlefthandthread]

Excellent video I haven't seen this method of removing it before. I have repair videos on KZbin too. I have never tried one of these chuck repairs before. Liked and subscribed well done my man.

[@matthewalexander8723]

Thank you sir… perfect instructional video.. been frustrated with my DCD791 for way too long.. did just as you instructed ( had to add some Blaster to loosen it up was getting nowhere ) and wham she came right off… Thank you once again… can’t thank you enough 👍

[@DoItWithDave]

I'm glad you found this video helpful. Thanks for watching!

[@kellyman75]

Best video I seen on this drill. This method works great. I was done in under 10 mins. Thx for the upload!

[@DoItWithDave]

I'm glad you found this video helpful. Thanks for watching!

[@johnrutherford4042]

Excellent tutorial and great to follow well done sir

[@WilliamRoberts-w5l]

Thank you so much. Your explanation together with the demonstration have proved invaluable. 6:51

[@DoItWithDave]

I'm glad you found this video helpful. Thanks for watching!

[@juanjosesalazar7752]

Amigo ha encontrado el santo grial para el reemplazo de ese mandril , gracias por su video👏👏👏

[@joaquinsuarez6090]

Great, thanks. What to do if teeth are all the way open and don't close to grab the 55 torks or large allen wrench to losen chuck? Please advise anybody.

[@Mardy-old-Bstard]

You are an absolute star. Just done it with mine. Like a new drill now. Thank you.

[@DoItWithDave]

Thanks for watching!

[@douglasslack4291]

Thank for this video , I did exactly as shown and the chuck came away very easily. Great job

[@DoItWithDave]

I'm glad you found this video helpful. Thanks for watching!

[@douglasslack4291]

@@DoItWithDave thank you Dave for posting a useful video , there are so many on you tube that have no idea really what they are doing but just stumble along , but yours was very sensible and informative. Thank you

[@garysmith594]

Worked a treat ! Saw the full dismantle videos before I found this and didn’t fancy trying that. Hoped this would work for me and it did, Not only that it was easier than I thought it would be, Thanks

[@DoItWithDave]

I'm glad you found this video helpful. Thank you for your comment and thank you for watching!

[@emiltegler1043]

Was able to just do this with the 791 ! This model has the chuck more sunken in so the outside is a little damaged after i was done. But since there was a small drill bit actually stuck in my chuck I think this was my only option. Thanks for this video!

[@DoItWithDave]

I'm glad you found this video helpful. Thanks for watching!

[@AndyMaclocklab]

Works a treat 👍 Had to use a bit of heat to get mine to come undone but saved me hours of stripping that drill down good as new now

[@reconbbs360]

Wish I found this video prior to dismantling my DCD797 to attempt to replace the chuck. Didn't go so well to say the least. LOL. Ended up upgrading to the DCD805. At least I have the Rohm chuck still as a spare.

[@alialavi8758]

Me too, Thank for this video , I did exactly as shown and the chuck came away very easily. Great job

[@DoItWithDave]

Thanks for watching!

[@manordafbedandbreakfast6102]

Saved my Bacon. worked well for me despite having what I thought was no pin. the pin head snapped off allowing me to change the chuck. I am happy with that!

[@jeffmills9964]

Although I was sceptical this method worked extremely well for me the chuck prised off very easily without any damage to the surrounding housing -maybe I was lucky for once-. The method for removing the chuck from the spindle also worked well I used an old Vileda mop metal handle cut in half for extra leverage on the allen key and Spanner which I thought would split due to the thinness of the tubular steel used in its construction but didn't. Excellent Instructions thank you very much.

[@DoItWithDave]

Thanks for watching!

[@kyleabbott2021]

Thanks for the info. I ran into an issue reassembling though where the drill was stuck in hammer mode. Turns out the bearing and gear under than metal cap with 3 screws are press fitted to the shaft, so you have to press them back on otherwise it’ll just hammer.

[@geoffsmalley5409]

I have the same problem, and took the three screws and plates off, but I can't see how to press it back in, I've tapped it with a hammer gently, To no avail

[@geoffsmalley5409]

How do you press it back?

[@Dave-rn1rm]

Looks easy. Will try it when new part arrives.

[@diegojcr4657]

Great video, the best method I've seen. He recently purchased the DeWalt DCD800, which came with the chuck with some annoying movement. This model has the same problem, it does not have a fixing screw. Will the Rohm chuck you used work on the dcd800? Thank you so much. Greetings!

[@titankh846]

Thank you! It worked! will be buying the new chuck as advised! Thanks again!

[@shashichauhan5858]

Helpful towards the similar issue l have,I will try this, thanks

[@evapendaki2530]

Thanks for the advice Unfortunatly I bought a rubish dewalt DCD 796. it will be the third chuck in three years

[@Omar-cr8js]

Hello, your video is brilliant, I have followed the steps, I have used your method because I couldn't remove the t20 torx screw inside, I just want to know what should I do as next step on putting everything back together regarding I have the t20 screw. My drill is DCD795. Any advice please?

[@Omar-cr8js]

Also the torx screw bit when removing actually snapped off the little bit. Do I actually need this part for my drill when I'm going to put together

[@crawz83]

Currently trying to figure out chuck removal on a DWD520, it appears to have no set screw and freely spins so hitting an allan key is pointless. I wonder if it will pull out too?

[@DoItWithDave]

You could give it a shot. Maybe pry up a bit and see if it starts to pull up without having to use too much force. No set screw I'd think it'd be the same set up. There's always a complete disassemble and reassemble process. I hope this helps.

[@johnmac5141]

Excellent video, just done mine now 👍

[@DoItWithDave]

Nice! Thanks for watching!

[@geoffsmalley5409]

I did this to my drill just to test it to see if I could get it out as you did, I did get it out quite easily, but when I put it back it only operates on hammer whatever setting that you put it on, can't understand this any ideas

[@DoItWithDave]

I ran into that issue a bit later after doing this. I used a c-clap placed on top of the chuck and on the back of the drill (ferring strip on housing) to seat the double D fitting. I hope this helps. Thanks for watching!

[@joshuaculbertsn10]

Thank you I just changed my one and it’s works great

[@dlm3027]

I couldn't see the part number on that Rohm chuck to look it up. What is it so I can order one? Thanks.

[@DoItWithDave]

There's an Amazon link to it and the part number in the description.

[@jorgerocha7499]

Buenas tardes amigo tengo un taladro dewalt mod dcd 7781 se puede quitar el portabrocas higual como ese que tu se lo quitaste espero tu tespuesta y gracias por compartir tus videos muy claros y bien explicados y me gusto tu video y tenga su like gracias

[@greg42864]

Thanks! This was pretty easy.

[@DoItWithDave]

Thanks for watching!

[@DiligentDave1966]

I love your channel name. I just subscribed, by the way.

[@timjones6637]

What is the purpose for the big bolt looking at the tip of chuck for??

[@DoItWithDave]

I think you're referring to the "Set Screw". It's used to hold the chuck in place.

[@timjones6637]

@@DoItWithDave lol, I know what set screw is.. I’m sorry. What I mean at the near of chuck tip it look like 3/4 nut … assume it just a style??

[@DoItWithDave]

@@timjones6637 if you're referring to the new Chuck in the video I believe it can be used to loosen and tighten the chuck to the shaft instead of using an Allen key?

[@dekurvajo]

@@DoItWithDave i think so too.

[@brunoblanc9883]

J'ai une perceuse scheppach, rien à voir avoir la qualité de votre matériel. Mais j'ai un problème idem au votre et comme je ne trouve pas de tuto sur la perceuse 20 pro scheppach, je vais essayer votre méthode. Merci pour la démonstration 🎉

[@mariajuliauslenghi8122]

Helo, of de Argentina, sory for my english. In my dewalt dcd 985 the chuck broken but it is closed. I dont see screw in. Do you know if it has screw, to remove only lever, (minute 2/3.Thanks you so much

[@DoItWithDave]

So based on the blown out images it looks like it does have a set screw. The link below will show it. Look at 21. www.ereplacementparts.com/dewalt-dcd985m2-type-20v-hammerdrill-parts-c-1009_9661_566974.html I hope this helps.

[@mariajuliauslenghi8122]

thank!! 21

[@DanielDaniel-lq1cf]

Do you think it could work also on 996 model?! Great video!!

[@DoItWithDave]

If you don't have a set screw it may. If you do try this definitely don't force it. It should come up slowly but surely. I hope this helps.

[@Crysalis02010]

Did you ever try this? I have TWO DCD996 with bad chucks. Contemplating trying this vs complete disassembly.

[@hermesrodolfoescobarvelasq1237]

Thanks so much. I'm from Guatemala central américa, your video help me. Excuseme, because mi English is not very good.

[@DoItWithDave]

@@hermesrodolfoescobarvelasq1237 thanks for watching! I'm glad you found this video helpful.

[@jsimm4587]

Im gonna squeeze my chuck tightening sleeve in the vice and make it bite at least I think I can . I took channel locks and put them in the vise ti squeeze harder and turned the drill to get my bit out si I think you can crush the sleeve and get it to work . I didn't smash it with that method but it won't tighten on a bit but a hex insert it will but slips . I think this will work .

[@pohlr1]

Got the chuck but since chuck won't tighten at all I may have to replace the shaft as well

[@DoItWithDave]

Idk if you've tried tapping the teeth in the chuck and spinning it a bit to try to get them to tighten. It may be possible to get a big pair of channel locks to hold the bottom of the chuck while you untighten the shaft.

[@rickyrickharris4908]

Ive got a bit stuck in mine and used channel locks to losen chuck well it started spining alright but bit didn't loosen at all now iv got a free spinning chuck with a bit stuck in it lol. So at least i can get the chhuck off ill find a way to loosen it once its off

[@rickyrickharris4908]

Is your drill newer than mine, mine is dcd795

[@DoItWithDave]

Not sure. Got mine in 2017 as part of a package deal.

[@joaquinsuarez6090]

I found an easier way to remove chuck: I put a vicegrip on bottom of chuck and hitted down with a hammer a few times and came off within a couple minutes.

[@juanjoseamador7614]

There's nothing more annoying than having to hand-screw something together kzbin.infoUgkx1McjgiqTNcTjrhvRvJWcrk5bzTeQW-Wn except for the pain in your wrist that is. This addition to my tool kit is great and I can get a lot done without all the pain and annoyance. The battery last's a long time and I have yet to run out of power when doing a small project (granted I am saying small project because I'm no construction worker). The only thing that I wish it had was an LED or pair of LEDs to indicate when it was charging and whether or not the charge was complete (or full).

[@shamoolkhanhorrorchannel5712]

Gr8 and easy way. Thanks

[@benberza9664]

Thank you great video

[@moegir]

It worked perfect for me

[@Leo-gt1bx]

Mine just gave up a week out of warranty really annoyed. Used adjustables a few times and now my chuck is distorted.

[@rafaelqds]

You saved me!!! tnks a Lot!

[@14super]

perfect! fast and easy thanks!

[@shamoolkhanhorrorchannel5712]

Amazing trick

[@scrashnet]

This is THE BEST technique, BY FAR!!!

[@nereomedinapena9664]

Fabuloso gracias amigo eres grandioso

[@jessperez477]

So I noticed that the chuck just came out with prying so I used a large vice grip pliers to grip the chuck and I waked the pliers with a Mallet, gave it 10 good hits and it flew off. Took me literally 1 minute.

[@DoItWithDave]

Good show! Thanks for comment. I helps the community greatly.

[@jessperez477]

@@DoItWithDave also the front of the chuck has a hex bolt that you can put a 5/8 size socket on and really grip it well with a ratchet. So you don’t have to use a Allen key, mine was stuck open so there was no way for me to put an Allen anyways. But a crescent wrench and a 5/6 socket made quick work of it.

[@danialtun5431]

Some people replacement chuck is all open to change

[@markm0000]

Thanks 😊

[@mauriciopallero6947]

Gracias🇺🇾

[@Robcatist]

The other fault with these exact drills is they get stuck on hammer action the internals on these are so cheap nowadays.

[@DoItWithDave]

I know it's pretty frustrating. Silver lining I got a 7 piece kit with hard box on wheels for $499 around 4 years ago and it paid for itself many times over. Thanks for watching.

[@twofortyrida]

Mine is stuck on hammer mode now lol

[@MrLonstar]

Watch this video, it shows what you need to do to fix hammer only mode. kzbin.info/www/bejne/m6CVeHp7bqx_gqs

[@geoffsmalley5409]

So is mine

[@twofortyrida]

@@MrLonstar I appreciate it

[@YouCantSeeMeENT]

Has anyone tried this on a dcb999

[@BarlitosC]

Can buy a Bauer hammer drill for $40 & have the $18 battery adapter. Think the drill is total loss for $34 chuck + time and not a hammer drill… not happy 🤷🏻‍♂️

[@johnjkizer6399]

Actually after looking at most of the videos here on KZbin regarding removal of chuck on these DCD drills, your doing it wrong, the way your doing it, it removes the stem which you do not want to remove, it’s done exactly the same way as they chucks with the set screw, if no set screw just simply tighten with a large Allen wrench and hit with a hammer, once loose just unscrew and screw on new chuck

[@DoItWithDave]

Why don't you want to remove the stem?

[@johnjkizer6399]

@@DoItWithDave if your only replacing the chuck, the. Chuck is the only thing that should be separated from the drill itself and when your buying a replacement chuck you will only get a chuck, no stem, so basically your doing more work than needed. Peace

[@DoItWithDave]

@@johnjkizer6399 okay I understand now. Simply removing the chuck with Allen key and hammer is definitely the best way to go about it. I my case I literally spent an hour using the preferred method to no resolve. Even tried a heat gun. I only showed it this way because of that and was hoping to help anyone else that was having the same issue. Thanks for your post. More information definitely helps anyone trying to replace their drill chuck.

[@037ln3]

muy mal montaje del chuck, golpeando se daña el taladro

[@joaquinsuarez6090]

Enseña un mejor metodo!