Easy E-Bike DIY ⚡️🚲⚡️ Waching Machine Motor + Bike

[@hellohun7331]

If the modern world came to an end, these guys wouldn't know it.

[@uK8cvPAq]

@Psychedelic Mind I honestly think people like this have the best chance of surviving climate change.

[@jtreg]

Brilliant guys

[@Trikipum]

They are the kings when the apocalypse comes...

[@JAYZWORKSHOP]

hello hun ha ha yeah true, I just built a 250w ebike from a cheap kit on my channel.

[@robertthompson959]

These guys lived in Ukraine and had a TV/Radio Repair Shop. They started their channel during the war in Ukraine. So basically the modern world had come to an end for them. I think they must have been making money from their channel because they have done a ton of videos (unfortunately most are in Russian).

[@intothecalm420]

Russian welding glasses: turn head, close eyes!

[@fraaggl]

protection for baby, russian eyes immune to welding..

[@minhvotran1115]

@@fraaggl in Vietnam , there are a lot people that do the same as this guy lol

[@fraaggl]

​@@minhvotran1115 i look at a vietnamese guy on youtube who weld bare foot and without glasses so you are right !!

[@droidking614]

they're ukranian...

[@carlyoung123]

Like AVE would say time to engage safety squints.

[@FenrirRagnulf]

"looks like a seat for haters" lmao

[@oofig]

I had to replay that to make sure I heard right

[@FenrirRagnulf]

@@oofig Dude, shit had me dying, lmao.

[@MaximumEfficiency]

timestamp?

[@royborrill2711]

No, for batty boys

[@peterzingler6221]

Pushes 400amps through small wire... "why is it hot"

[@oofig]

I don't think it's that many amps... Maybe 100 amps

[@johnnymotors2023]

Guys wtf 😂 400 Amps ? 100 amps? 😂😂🤣🤣🤣 That motor has maximum 600W not 88000W or 22000W 😂😂😂 A house has a fuse of about 40A to 60A. This motor having maximum of 600W uses 2.6A to maximum 3A not 100A. Because is 220V x 2.6A which gives about 572W. So as long as they have above 2.6A then they can have a good torque on the motor to push the person on the bike.

[@girlsdrinkfeck]

@@johnnymotors2023 thats still a thin wire for 20a

[@johnnymotors2023]

@@girlsdrinkfeck well yeah if you pass lots of Volts or Amps through it. But if it was 10A at 12V it would be fine or 5V at 20A but more than 100W is not that good for a long period of time.

[@mashedpotatoes5323]

@@johnnymotors2023 it's not the voltage that heats up the wire it's the amps

[@Litepaw]

You should make a washing machine using e-bike parts as a challenge 😃

[@tilakjain8343]

😝😝

[@raptordon7696]

“The tire got 30 patches” (Turn it around “Made in USSR“

[@79tazman]

USSR folded in 1991 it just shows how old that tube is. No wonder why it has 30 patches one foe each year LOL!!

[@MaximumEfficiency]

lol

[@sam-n7nevada370]

Russia : Never mind

[@norby93]

At what minute?

[@raptordon7696]

@@norby93 7:11

[@Drexfam2023]

These guys basically live in a workshop. They are Einsteins of the Ukraine.

[@ww07ff]

I love your invisible welding mask!

[@mushroomsamba82]

2:05 safety squints engaged!

[@Justin-lf1fs]

Yeah I had my safety glasses on while watching

[@Shwarmageddon]

0:53 this guy just stared at the weld and absolutely torched his corneas

[@johnnymotors2023]

Nah he closed the eyes 😂 I weld with normal sticks and they are a pain in the ass with that mask so sometimes I just close the eyes right before I touch the metal if I spot-weld.

[@snootdingo9365]

Say "Hello itchy corneas!".

[@JesusisJesus]

Johnny Motors Good luck with that, you hero. There’s light in the UV range that will still cook your retinas. Use a mask!

[@johnnymotors2023]

@@JesusisJesus I don't look into the light the whole time, just till I touch the stick to the metal 😂

[@JesusisJesus]

Johnny Motors Enjoy the sunburn. UV passes through many things.

[@ordnaelshideout]

As an Italian, I loved that sudden "mamma mia!" ❤

[@cianuro6210]

Allora non so l'unico italiano che guarda sto canale

[@ordnaelshideout]

@@cianuro6210 siamo minimo noi 2 😂

[@tysonty5989]

Siamo gli unici che vedono cose di qualità

[@alesschim2004]

@@cianuro6210 eh no

[@Sassenhaim]

All made famous by an Japanese Italian plumber 🤣😎

[@AtlasReburdened]

Gotta love those universal motors. If you're powering it straight from the battery you should be able to PWM power to the motor to get throttle, just make sure the FETs are logic level and flyback diodes are good, and you can use the signal from the accelerator you already have.

[@matsushibaexperiments3201]

What! " WATCHING MACHINE "😂😂😝😝😝😝😝

[@huibvanderveur3015]

"it has a nuclear speed now "

[@LeonidAndronov]

вам бы ещё переводчика, который разбирается в электротехнике)

[@BagheeraTube]

Yes please 300 volts sounds awesome 😁

[@ovanai6277]

Yes i agree😅😅

[@IndoorGeek]

"Recently, the washing machine has gone crazy!" I'm not sure about that.

[@ColAngus]

KREOSAN Motorcycle Company " I can feel the thrust now"

[@lukepotosky7710]

0:15 His neighbors must love him!

[@alichank]

7:45 for a second i tough you're talking about Half-Life 2. Yes in this game combine is a type of soldiers

[@nickgalena1]

i see you use security shoes - also for welding - nice !

[@johnniederhofer5472]

put the battery in the front to prevent wheely pops. use solid inner tubes for the wheels purrrrfect

[@snowdaysrule]

My lord that bicycle tube had 31 patches on it. 31!

[@reggiep75]

5:54 - I was laughing pretty good at this part! You fellas are total steampunk tech gangstahs.. NEVER CHANGE!!! #NUCLEARSPEED #THRUST #DEMONICPOWER

[@scellyyt]

I love how resourceful you guys are

[@ss-sq1hn]

3:36 it sounds just like a washing machine.

[@major7004]

Well, no shit.

[@JohnyStone888]

"Now it feels normal." * Drives away on rusty bike propelled by washing maschine motor with extension cord *

[@musicwiz40]

What in the third world country did I just watch?

[@hassanila]

0:05 Exynos Processor 0:13 Snapdragon 865

[@m0w0ss]

How about 855+

[@khalilaputrirahmawati2276]

Haha

[@LeoPlus]

Ахахаахаххах

[@sebbes333]

*@KREOSAN English* ----> to *@WeldingDude* eg: 7:35 Make him use welding glasses, so he don't get blind in like 3 years from now. Or at least take some regular glass & black it with fire. The danger is from UV- & IR-lights, that we can't see. those "protective" see-through glasses does NOTHING to stop the dangerous lights.

[@garystinten9339]

Or use wish.com and get cheap welding glasses

[@vuaeco]

Forget about the bike. This guy's problem solving skill is second to none!

[@markthomas4992]

That’s not a battery - it’s a BOMB lol 😂

[@n0fluxgiven486]

Love these videos! I have an old rusty cycle like that at our village house, I'm thinking to somehow power it with a drill motor or something. Your videos are a great inspiration for ideas.

[@orionx8295]

Use any Motor from a Scrap Car...Heater Blower Motor.....The Starter is good...and Powerful..and They only Require 12 Volts to Run....I Made one with an old Blower Motor and it will go 35 to 40 Kph....And I use Li Ion Batteries in Blocks to Power it....And an old Drill Switch as a Throttle.

[@jayakar1970]

@@orionx8295 dude starter motors are good for short use only. They'll burn out after long periods of use

[@Chip1189]

This literally just when through my head like 5 minutes before I seen it in my suggestions

[@ianphilip6281]

Ear defenders and safety glasses for grinding. As for welding.. Not so much. "Nah mate.. I'll blink, I'll be a'ight." hahahaha

[@tox1cfuse347]

The guy doing all the work looks like Pete Buttigieg

[@TheElectricTides]

YOU GUYS ARE AWESOME!!!!! MUCH LOVE FROM OVER HERE IN CALIFORNIA!!!!! NEVER STOP CREATING AND INSPIRING!!!!! THANK YOU FOR ALL YOUR VIDEOS =)!!!!!!!!

[@wengoweng3530]

when the Dead scrap turns to life nice👍👍👍 new subs here guys.

[@JAYZWORKSHOP]

I just built a 250w ebike from a cheap kit on my channel,

[@sofyan3]

Mammamia.. I'm amazed by their craftmanship.. So dark and gothical.. Worse than indian at work.. Keep it up..

[@aayush7645]

Sir you could have used a tire jack to increase the width of the frame near the rear wheel. Would have saved a lot of time and stretched the frame without breaking it but lovely video

[@gursisingh1940]

The amount of diy in just this one video is mind blowing ahahaha

[@SkywereProductions]

USSR Tire, nice

[@yatckov]

This guy lives in Ukraine occupied by Russia. Therefore, he lives in the USSR. And he has no future

[@townsville69]

@2:16 Futuristic ? Yeah Mad Max future. You will ride eternal, shiny and chrome.

[@Purpsmcgee]

"Cuts bike frame" alright let's see how fast we can make this bad mamma jamma 😂

[@snootdingo9365]

This is "EASY" in the Ukraine, but in the States, I'm afraid this is forbidden alchemy. Well done!

[@KennedoMaker]

Another great upload!

[@scratchdog2216]

You folks make the coolest stuff. Thanx for the post.

[@BagheeraTube]

Awesome! Been waiting for this

[@MakarovFox]

next build a ultra long extencion cord

[@TheMaxthesis]

Bra jobbat grabbar! Schysst hoj!

[@CoolDudeClem]

Easy E-bike DIY ... *starts cutting and welding*

[@michaelprice3031]

That's so sketchy! I love it!

[@jamest.5001]

That motor would probably handle 400vdc for about 30 minute burst, maybe add a fan to help cool the brushes! Don't forget, as volts go up so does the current, meaning double volts, 4x the wattage,

[@camshaftshaft2711]

Love your channel guys 👍😎✌️ especially Pripyat adventures 😎😎😎! Keep it up 👍

[@alexandernaydenov7400]

Welds pedal crank to axle - "It will serve you forever now" Yeaaa, Eastern style ftw!

[@freedom341]

putin wants to know ur location

[@steviebboy69]

I like the bike, at first I thought you would need a big loooonnng extension cord to power it. Those washing machine motors do crazy RPM's.

[@tahanlaoboy]

Nicely done

[@bomblifenewzealand]

So he ended up connecting the battery directly to the motor? No inverter and it went faster?

[@abyssmanur3965]

It looks like a universal motor which can run on ac or dc but I think you need a min of 50v to get any real power if running DC.

[@joshzimmermen7686]

Welding without eye protection lmao

[@electricvehicles1772]

Nice guys keep going making this videos😂😂👌👍👍👍

[@phil85813]

"this all looks reliable"

[@abyssmanur3965]

I like the rim as a pulley idea!

[@rich_edwards79]

"If my calculations are correct, when this baby hits 88 miles per hour... you're gonna see some serious shit."

[@bwc1976]

I want to see them put a flux capacitor into a Lada!

[@nicksgarage8295]

the gearing is way too low, you make the gearing steeper, will go much faster...

[@crownfam882]

Hahahaa you guys are great.you look like a young Vladimir Putin.nice creation🍻👍

[@jamess1787]

RIP AUSSIE50. First to do the washing machine on KZbin.

[@daspec]

Put a LARGER pulley on the motor shaft. The one you have is too small. It has to be at least 5 cm in diameter.

[@skarekr0w3]

Your neighbors must love you! Futuristic, I just don't know if the world s ready for this....

[@79tazman]

That bike tube is an antique the damn thing has tons of patches on it and it has made in the USSR on it LMFAO!!! The USSR have not been around since 1991

[@79tazman]

It has nuclear speed now LMAO!!

[@user-blaster_2012]

WAY TO GO!!!......now ride it to Pripyat.

[@Mrugendraa]

CREATIVE + IN SANE = KREOSAN...!!! 🤪😎 I LOVE YOUR IDEAS...! Next time use super Capacitors/ high ampere for your EV ...! we want to see what happens 🙃 !!!

[@HDSInvention]

Great work

[@franks9621]

Meth/Mith Busters ha ha!

[@CarlJohnson-wk3rv]

Next video: how I built my own Tesla

[@macanalista]

Does somebody know why not using the inverter used on the other bicycle (the 12v DC to 220v AC)?

[@defowler2005]

Because the the AC motor already an AC motor.

[@Good-Enuff-Garage]

are these available for sale, are you accepting pre orders?!

[@olle6727]

What was that about artillery?

[@Sacred_Samurai]

I would love a DIY vehicle. This is the type of videos that I like. Is it possible to put 2 washing machine motors to make the bicycle faster?

[@bwc1976]

"It has a nuclear speed now!" "Demonic power"

[@danielsepulveda9768]

This is far better than "Jackass"... At least you get to learn something!

[@BenHelweg]

I love this channel

[@alexandrossotiropoulos5621]

This would be a good project for a motorcycle

[@mattheweburns]

So awesome guys! The idea about the throttle seems similar to the Excelerator pedal on new cars these days… Although I prefer something more direct as well. Thanks for the videos, cheers!

[@karolkowalski3842]

welding without mask xDD

[@homes24]

эти птицы так раздражают!

[@0_Ka-Bar_0]

Slavic science!

[@RaptorProducts1991]

0:03 USSR scientists' first attempts to build the atomic bomb (1943, colorized)

[@billis9999999999]

Try placing a pure sine single-phase transformer with a power supply of more than 1000 watts on the bike and have it on the frame. Then you plug the washing machine motor cable into the pure sine transformer. after you do it the motor will work at 15000 revolutions. To adjust the revolutions from the motor you will need a speed controller for 12 volts or for 24 volts. If necessary, try placing a gear on the motor shaft and a different gear on the rear wheel shaft. Install a chain from the washer motor to the rear wheel sprocket.

[@AL-PAKA]

Wrong

[@drsamuelk]

What voltage and amps is the motor running on? Did you use a regular household inverter.

[@jerrystone1]

the leagacy lives on!

[@frankstocker5475]

The 30 patches have a little bit of tube.

[@l1u1c1k]

I’m glad he he chose the batterie model 😂😂

[@eduardoherrera4894]

i come to this chanel every time i want to know how everything amazing

[@savneetsinghrairai6823]

Oh no😂🤣🤣🤣🤣🤣washing machine💣💣💣💥💥💥💥💥☻☻☻😜😂😂

[@Biffo1262]

We been more extension leads so I can reach the shops!

[@ketas]

wired bike is just priceless

[@madisondukes7789]

I know how it seems like the least of the problems but damn I never see a welding shield 😂😂 dude must have cyborg eyes 😂😂